Test 20 Type SMK

Test 20 Type SMK Connection Thread M 16 x 2
TEST
STA
STA
Test hose
with swivel nut
Test coupling
Protective cap
Fast Coupling for:
• Monitoring and control of pressure
• Venting
• Sampling Fluids
Advantages:
• Test system at working pressure
• Connection is leakproof before ball check is open
• Simple connection to measurement,
control and switching devices
• Self locking metal protective cap
• Minimizes introduction of contamination
into hydraulic systems
Working Pressure:
• Max. working pressure 9000 PSI (630 bar)
For SMK style G, K and S the recommended working
pressure of fitting manufacturer should be noted
• Connection under pressure up to 5800 PSI (400 bar)
max.
Materials:
• Metal parts: Steel, Stainless Steel on request
• Ball: Stainless Steel
• Seals:
Standard
V = FPM-VITON Temperature range
Optional
P = NBR-BUNA Temperature range
E = EPDM Ethylene Propylene (for Brake Fluid)
Temperature range
– 4˚F to +392˚F
(– 20˚ C to + 200˚C)
– 4˚F to +195˚F
(– 20˚ C to + 90˚ C)
– 40˚F to +302˚F
(– 40˚ C to + 150˚ C)
• Hose: Polyamide Temperature range –31˚F to +212˚F
(–35˚ C to +100˚ C)
Media:
• Suitable for hydraulic oils and other mineral based fluids
(Check compatibility of seal material)
• For use with other liquid media, low viscosity media or
gaseous media please consult STAUFF details
• SMK20 - 1/4" NPT - VD-ETG version available for severe
shock / vibration applications
STAUFF
T2
The complete STAUFF-TEST-20-Type-SMK range is also
available with hexagonal protection cap made of steel or
plastic protection cap

Test 20 Type SMK Connection Thread M 16 x 2
Test Coupling with Protective Cap SMK
h Hex Order No. (Add C6F for Standard Finish)
Thread
G mm mm
Seal Type
FPM (VITON)
in in NBR (BUNA) (Standard) (see below)
M8 x 1
37 17
1.46 0.67
SMK 20 – M8 x 1 – PA SMK 20 – M8 x 1 – VA O-Ring Type A
STAUFF
M10 x 1
1.46 0.67
37 17
SMK 20 – M10 x 1 – PA SMK 20 – M10 x 1 – VA O-Ring Type A
M 16
1.46 0.75
M12 x 1,5
1.46 0.67
37 17
SMK 20 – M12 x 1.5 – PC SMK 20 – M12 x 1.5 – VC O-Ring Type C
M14 x 1,5
37 19
SMK 20 – M14 x 1.5 – PB SMK 20 – M14 x 1.5 – VB Metal joint Type B
M16 x 1,5
37 22
1.46 0.87
SMK 20 – M16 x 1.5 – PB SMK 20 – M16 x 1.5 – VB Metal joint Type B
Hex
G 1 / 8
1.54 0.67
39 17
SMK 20 – G 1 / 8 – PC SMK 20 – G 1 / 8 – VC O-Ring Type C
G 1 / 4
1.46 0.75
37 19
SMK 20 – G 1 / 4 – PB SMK 20 – G 1 / 4 – VB Metal joint Type B
G 1 / 4
37 19
1.46 0.75
SMK 20 – G 1 / 4 – PC SMK 20 – G 1 / 4 – VC O-Ring Type C
G
G 3 / 8
1.46 0.87
37 22
SMK 20 – G 3 / 8 – PB SMK 20 – G 3 / 8 – VB Metal joint Type B
R 1 / 8 taper
1.46 0.67
37 17
SMK 20 – R 1 / 8 K-PD SMK 20 – R 1 / 8 K-VD Taper Type D
R 1 / 4 taper
1.42 0.67
36 17
SMK 20 – R 1 / 4 K-PD SMK 20 – R 1 / 4 K-VD Taper Type D
1 /8 NPT
1.42 0.67
36 17
SMK 20 – 1 / 8 NPT-PD SMK 20 – 1 / 8 NPT-VD Taper Type D
1 /4 NPT
35 17
1.38 0.67
SMK 20 – 1 / 4 NPT-PD SMK 20 – 1 / 4 NPT-VD Taper Type D
5 /16 – 24 UNF
1.50 0.67
38 17
SMK 20 – 5 / 16 UNF-PE SMK 20 – 5 / 16 UNF-VE O-Ring Type E
7
17 10
/16 – 20 UNF 38 17
1.50 0.67
0.67" 0.4"
1 /2 – 20 UNF 38 17
1.50 0.67
SMK 20 – 7 / 16 UNF-PE
SMK 20 – 1 / 2 UNF-PE
SMK 20 – 7 / 16 UNF-VE
SMK 20 – 1 / 2 UNF-VE
O-Ring Type E
O-Ring Type E
9 /16 – 18 UNF 37 19
1.46 0.75
SMK 20 – 9 / 16 UNF-PE SMK 20 – 9 / 16 UNF-VE O-Ring Type E
3 /4 – 16 UNF
37 19
1.46 0.75
— SMK 20 – 3 / 4 UNF-VE O-Ring Type E
To order hexagonal protection cap, add “SK” to part number. To order Plastic Protection cap, add “KK” to part number.
Other port connections and seals on request.
h
Port Connections and Seals
Type A Type B Type C Type D Type E (ISO 6149)
TEST
d 2
d 1
G
30°
0.5
2.5
t 1
t 2
d 1
G
90°
t 1
t 2 a
d 1
G
90°
t 1
t 2 a
G
90°
t 1
t 2
d 1
G
12°
1,6
a
t 1
t 2
mm
mm
mm
G d 1 t 1 t 2 a
mm
mm
mm
mm
G d 1 t 1 t 2 a
mm
mm
mm
mm
G t 1 t 2
mm
mm
G d 1 d 2 t 1 t 2 a
mm
mm
mm
mm
mm
G d 1 t 1 t 2
5 /16 – 24 UNF
M8 x 1
M10 x 1
`M10 x1.25
9,5
11,5
11,5
in
0.37
0.45
0.45
in in
in in in in
in in in in
11 15,5
20 12 18,5 1,5
18 12 18,5 1,5
M14 x 1,5
M12 x 1,5
0.43 0.61
0.79 0.47 0.73 0.06
0.71 0.47 0.73 0.06
12 16,5
22 12 18,5 1,5
15 8 13 1,0
M16 x 1,5
G 1 / 8
0.47 0.65
0.87 0.47 0.73 0.06
0.59 0.31 0.51 0.04
12 16,5
19 12 18,5 1,5
19 12 18,5 1,5
G 1 / 4
G 1 / 4
0.47 0.65
0.75 0.47 0.73 0.06
0.75 0.47 0.73 0.06
23 12 18,5 2
G 3 / 8
0.91 0.47 0.73 0.08
T3
R 1 / 8 taper
R 1 / 4 taper
1 /8 NPT
1 /4 NPT
5,5
8,5
6,9
10
in
0.22
0.33
0.27
0.39
9,5
in
0.37
13,5
0.53
11,6
0.46
16,4
0.65
in
9,1
in in in in
17 10 12 1,9
0.36 0.67 0.39 0.47 0.07
12,4 21 11,5 14 2,4
7 /16 – 20 UNF
0.49 0.83 0.45 0.55 0.09
14 23 11,5 14 2,4
1 /2 – 20 UNF
0.55 0.91 0.45 0.55 0.09
15,6 25 12,7 15,5 2,5
9 /16 – 18 UNF
0.61 0.98 0.50 0.61 0.10
20,6 30,5 14,3 17,5 2,5
3 /4 – 16 UNF
0.81 1.20 0.56 0.69 0.10

Test 20 Type SMK Connection Thread M 16 x 2
Test Coupling SMK (Compression Ring Fittings acc. to DIN 2353) - Metric Tubing
ød
SW 1
SW 2
STAUFF
SW17
h
SW17
SW2
STAUFF
I 2 35
1.38"
SW17
STAUFF
Ød
l 3 35
1.38"
SW17
STAUFF
37
1.45"
l 3
TEST
Type G
Test coupling complete
with straight fitting
Type K
ød
Test coupling for 24˚
cone fittings
Ød
Type S Test coupling for compression
ring assembly
l 2 l 3 h SW 1 SW 2 Order No.* (Add C6F for Standard Finish)
Series PN Pipe
mm mm mm mm mm
Ød in in in in in Type G Type K Type S
L
S
6
15,5 20 49 24 14
0.61 0.79 1.93 0.94 0.55
SMK 20 – 6 L–VG SMK 20 – 6 L–VK SMK 20 – 6–VS
8
15,5 20 49 24 17
0.61 0.79 1.93 0.94 0.67
SMK 20 – 8 L–VG SMK 20 – 8 L–VK SMK 20 – 8–VS
315
10
16,5 22 49 24 19
0.65 0.87 1.93 0.94 0.75
SMK 20 – 10 L–VG SMK 20 – 10 L–VK SMK 20 – 10–VS
12
17,5 22 50,5 27 22
0.69 0.87 1.99 1.06 0.87
SMK 20 – 12 L–VG SMK 20 – 12 L–VK SMK 20 – 12–VS
15
21 25 52 30 27
0.83 0.98 2.05 1.18 1.06
SMK 20 – 15 L–VG SMK 20 – 15 L–VK SMK 20 – 15–VS
18
19,5 28 53 32 32
0.77 1.10 2.09 1.26 1.26
SMK 20 – 18 L–VG SMK 20 – 18 L–VK SMK 20 – 18–VS
22
20,5 30 55 36 36
0.81 1.18 2.17 1.42 1.42
SMK 20 – 22 L–VG SMK 20 – 22 L–VK SMK 20 – 22–VS
160
28
25 32 57,5 41 41
0.98 1.26 2.26 1.61 1.61
SMK 20 – 28 L–VG SMK 20 – 28 L–VK SMK 20 – 28–VS
35
30 42 60 46 50
1.18 1.65 2.36 1.81 1.97
SMK 20 – 35 L–VG SMK 20 – 35 L–VK SMK 20 – 35–VS
42
31 45 64,5 55 60
1.22 1.77 2.54 2.17 2.36
SMK 20 – 42 L–VG SMK 20 – 42 L–VK SMK 20 – 42–VS
6
14,5 20 49 24 17
0.57 0.79 1.93 0.94 0.67
SMK 20 – 6 S–VG SMK 20 – 6 S–VK SMK 20 – 6–VS
8
16,5 20 49 24 19
0.65 0.79 1.93 0.94 0.75
SMK 20 – 8 S–VG SMK 20 – 8 S–VK SMK 20 – 8–VS
630 10
16,5 22 49 24 22
0.65 0.87 1.93 0.94 0.87
SMK 20 – 10 S–VG SMK 20 – 10 S–VK SMK 20 – 10–VS
12
17,5 22 49 24 24
0.69 0.87 1.93 0.94 0.94
SMK 20 – 12 S–VG SMK 20 – 12 S–VK SMK 20 – 12–VS
14
19,5 22 50,5 27 27
0.77 0.87 1.99 1.06 1.06
SMK 20 – 14 S–VG SMK 20 – 14 S–VK SMK 20 – 14–VS
16
18 28 52 30 30
0.71 1.10 2.05 1.18 1.18
SMK 20 – 16 S–VG SMK 20 – 16 S–VK SMK 20 – 16–VS
400
20
24 30 55 36 36
0.94 1.18 2.17 1.42 1.42
SMK 20 – 20 S–VG SMK 20 – 20 S–VK SMK 20 – 20–VS
25
26 36 57,5 41 46
1.02 1.42 2.26 1.61 1.81
SMK 20 – 25 S–VG SMK 20 – 25 S–VK SMK 20 – 25–VS
30
30 41 60 46 50
1.18 1.61 2.36 1.81 1.97
SMK 20 – 30 S–VG SMK 20 – 30 S–VK SMK 20 – 30–VS
315 38
34 48 64,5 55 60
1.34 1.89 2.54 2.17 2.36
SMK 20 – 38 S–VG SMK 20 – 38 S–VK SMK 20 – 38–VS
* For EPDM seals replace “V” with “E”
T4

Test 20 Type SMK Connection Thread M 16 x 2
Test Coupling SMK – JIC Connection (to SAE-J514)
STAUFF
STAUFF
STAUFF
SW2
H
SW 17
H
SW17
H
SW1
SW1
G
SW
G
Type 1 Type 2
Pipe JIC H Type Order No.
H L I
Size Size G SW SW
(Add C6F for
SW
inch UNF mm inch 1 2 Standard Finish) mm inch mm mm
G
l
L
Order No.
(Add C6F for
Standard Finish)
1 /4 " – 4 7 /16 " – 20 52 2.0 17 17 1 SMK20-JIC 1 / 4 -VK 61 2.4 24 43 14 SMK20-JIC 1 / 4 -VG
5 /16 " – 5 1 /2 " – 20 53 2.0 17 17 1 SMK20-JIC 5 / 16 -VK 61 2.4 24 43 14 SMK20-JIC 5 / 16 -VG
3 /8 " – 6 9 /16 " – 18 55 2.1 19 17 1 SMK20-JIC 3 / 8 -VK 61 2.4 24 43.2 14.1 SMK20-JIC 3 / 8 -VG
1 /2 " – 8 3 /4 " – 16 56 2.2 22 19 1 SMK20-JIC 1 / 2 -VK 67 2.6 30 48.4 16.7 SMK20-JIC 1 / 2 -VG
5 /8 " – 10 7 /8 " – 14 59 2.3 27 22 1 SMK20-JIC 5 / 8 -VK 67 2.6 30 53.6 19.3 SMK20-JIC 5 / 8 -VG
3 /4 " – 12 1– 1 / 16 " – 12 70 2.7 32 2 SMK20-JIC 3 / 4 -VK 73 2.8 36 58.8 21.9 SMK20-JIC 3 / 4 -VG
1" – 16 1– 5 / 16 " – 12 69 2.7 38 2 SMK20-JIC1-VK 78 3.0 41 61.2 23.1 SMK20-JIC1-VG
1 1 / 4 " – 20 1– 5 / 8 " – 12 72 2.8 50 2 SMK20-JIC1 1 / 4 -VK 83 3.3 46 65.6 24.3 SMK20-JIC1 1 / 4 -VG
1 1 / 2 " – 24 1– 7 / 8 " – 12 75 2.9 60 2 SMK20-JIC1 1 / 2 -VK 92 3.6 55 72 27.5 SMK20-JIC1 1 / 2 -VG
l
TEST
Test Coupling SSK/SMK – ORFS Connection
M16
M15
hex 1
H
hex 1
H
hex 2
L
hex 2
L
Order Number Type Thread G H L Hex 1 Hex 2
(Add C6F for
Standard Finish)
mm in mm in mm in mm in
SSK20-04-ORFS-V 2 9 /16 " – 18 UNF 75 2.9 36 1.40 22 0.87 22 0.87
SSK20-06-ORFS-V 2 11 /16 " – 16 UNF 75 2.9 36 1.40 27 1.06 27 1.06
SSK20-08-ORFS-V 2 13 /16 " – 16 UNF 75 2.9 36 1.40 30 1.20 30 1.20
SMK20-04-ORFS-V 1 9 /16 " – 18 UNF 54 2.1 19 0.75 17 0.67 17 0.67
SMK20-06-ORFS-V 1 11 /16 " – 16 UNF 54 2.1 19 0.75 19 0.75 21 0.80
SMK20-08-ORFS-V 1 13 /16 " – 16 UNF 54 2.1 19 0.75 22 0.87 24 0.87
* For EPDM seals replace “V” with “E”
Thread G
Type 1 Type 2
T5
Thread G

STA
Test 20 Connection Thread M 16 x 2
Test Hose SMS (for gaseous media Specify Type SGS)
TEST
Max. working
pressure 9000 PSI
(630 bar)
Test hose:
Nominal bore 0.08"
(2 mm)
Minimum bending
radius 0.75"
(20 mm)
Nominal bore 0.16"
4 mm also available
Pressure/t˚ factor:
to 0˚C 122 %
at 30˚C 110 %
at 50˚C 100 %
at 80˚C 86 %
at 100˚C 77 %
Hose construction:
Hose-core and
-cover PA
Reinforcement:
Synthetic fibre
Bursting pressure:
27,000 PSI (1900 bar)
Length L (1) (± .25")
in
mm
Stauff-Test 20/20 Stauff-Test 15/20 Stauff-Test 10/20 Stauff-Test 12/20 (2) Stauff-Test 20/N 1 / 4
(3)
STAUFF-TEST 20 STAUFF-TEST 20 STAUFF-TEST 20 STAUFF-TEST 20 STAUFF-TEST 20
STA
STA
STA
STA
Ø5
Ø5
Ø5
Ø5
Ø5
L
L
L
L
L
STA
STA
STA
STA
S12.65 x 1.5
1/4" NPT
M 16
M 16 x 1.5
STAUFF-TEST 20 STAUFF-TEST 15 STAUFF-TEST 10 STAUFF-TEST 12 GAUGE ADAPTOR
Order No.
12
24
36
48
60
72
96
120
305 SMS-20 – 305mm-B SMS-15/20 – 305mm-B SMS-10/20 – 305mm-B SMS-12/20 – 305mm-B SMS-20/N 1 / 4 – 305mm-B
610 SMS-20 – 610mm-B SMS-15/20 – 610mm-B SMS-10/20 – 610mm-B SMS-12/20 – 610mm-B SMS-20/N 1 / 4 – 610mm-B
915 SMS-20 – 915mm-B SMS-15/20 – 915mm-B SMS-10/20 – 915mm-B SMS-12/20 – 915mm-B SMS-20/N 1 / 4 – 915mm-B
1219 SMS-20 – 1219mm-B SMS-15/20 – 1219mm-B SMS-10/20 – 1219mm-B SMS-12/20 – 1219mm-B SMS-20/N 1 / 4 – 1219mm-B
1524 SMS-20 – 1524mm-B SMS-15/20 – 1524mm-B SMS-10/20 – 1524mm-B SMS-12/20 – 1524mm-B SMS-20/N 1 / 4 – 1524mm-B
1829 SMS-20 – 1829mm-B SMS-15/20 – 1829mm-B SMS-10/20 – 1829mm-B SMS-12/20 – 1829mm-B SMS-20/N 1 / 4 – 1829mm-B
2438 SMS-20 – 2438mm-B SMS-15/20 – 2438mm-B SMS-10/20 – 2438mm-B SMS-12/20 – 2438mm-B SMS-20/N 1 / 4 – 2438mm-B
3048 SMS-20 – 3048mm-B SMS-15/20 – 3048mm-B SMS-10/20 – 3048mm-B SMS-12/20 – 3048mm-B SMS-20/N 1 / 4 – 3048mm-B
Custom lengths available on request
(1) Bending protection and
1) other lengths on request
(2) Special thread: buttress thread S12,65 x 1,5 (3) Gauge adaptor G 1 / 4 ,
G 1 / 2 and 1 / 2 NPT on request
Transition Adaptor SAD
M16 x 2
h
M16 x 2
h
G
Order No.
h
(Add C6F for Standard Finish)
Type
in
mm
NBR (BUNA) FPM (VITON)
1.53
M16 x 1,5
39
A SAD 20/15-P SAD 20/15-V
plug in
1.45
37
B SAD 20/10-P SAD 20/10-V
S12 1) 1.53
39
A SAD 20/12-P SAD 20/12-V
1)
Special thread: buttress thread S12,65 x 1,5
G
Type A
Type B
T6

4.05
5.68
Test 20 Connection Thread M 16 x 2 / Swivel Run Tees
Bulkhead SSK (for gaseous medium use type SSKK)
STA
STA
h
Order No.
(Add C6F for Standard Finish)
G
mm
Type
NBR (BUNA) FPM (VITON)
in
(Standard)
M16 72 2.8
A SSK 20–P SSK 20–V
SW19
SW19
max. 12
(1/2")
h
SW19
SW19
max. 12
(1/2")
h
M16 x 1.5 1) 72 2.8
B SSK 20/08 S–P SSK 20/08 S–V
M18 x 1.5 1) 72 2.8
B SSK 20/12 L–P SSK 20/12 L–V
7/ 16 UNF
(– 4 JIC)
63
2.48
A N/A SSK20–J 7 / 16 UNF–MV
1) Compression ring assembly 8 S/12 L acc. to DIN 2353
G
Type A
Gauge Adaptor SMA
max. 12 (1/2")
G
SW
SW19
M16
h
G
Type B
Mounting hole
Ø 18 mm
(0.17")
Order No.
h SW
(Add C6F for Standard Finish)
G
mm mm
NBR (BUNA) FPM (VITON)
in in
(Standard)
G 1 / 54 19 4
2.12 .75 SMA 20 – G 1 / 4 – P-OR SMA 20 – G 1 / 4 – V-OR
G 1 / 64 27 2 2.52 1.06 SMA 20 – G 1 / 2 – P-OR SMA 20 – G 1 / 2 – V-OR
1/ 4 NPT 54 19 2.12 .75 SMA 20 – 1 / 4 NPT–P SMA 20 – 1 / 4 NPT–V
1/ 2 NPT
64 27 2.52 1.06 SMA 20 – 1 / 2 NPT–P SMA 20 – 1 / 2 NPT–V
Snubber on request
TEST
Direct Gauge Adaptor SMD
G
SW
h
h SW
Order No.
(Add C6F for Standard Finish)
G
mm mm NBR (BUNA) FPM (VITON)
in in
(Standard)
G 1 / 41 19 4
1.61 .75 SMD 20 – G 1 / 4 – P-OR SMD 20 – G 1 / 4 – V-OR
G 1 / 51 27 2 2.0 1.06 SMD 20 – G 1 / 2 – P-OR SMD 20 – G 1 / 2 – V-OR
1/ 4 NPT 41 19 1.61 .75 SMD 20 – 1 / 4 NPT SMD 20 – 1 / 4 NPT
1/ 2 NPT 51 27 2.0 1.06 SMD 20 – 1 / 2 NPT SMD 20 – 1 / 2 NPT
7/ 16 – 20 UNF
41 19 1.61 .75 — SMD 20 – 7 / 16 UNF
Swivel Run Tees SGV
M16
Snubber on request
—
Order Code Without Test Point
Thread
Ød1
hex 2
37°
15 (0.59")
7/16-20UNF
l4 l1 hex 1
l3
l2
37°
Ød2
Thread
Thread
Ød1 Ød2 l1 l2 l3 l4 Hex1 Hex2
G mm mm mm mm mm mm mm mm
Order No.
in in in in in in in in
7 / 16 – 20 UNF
7.49 4.9 9 14 37 8 27 17
.29 .19 .35 .55 1.46 .31 1.06 .67
SGV 7 / 16 UNF – 04 – JIC 1 / 4 – F/M
9 / 16 – 18 UNF
11.1 8.1 10.5 14.1 37.6 8.5 27 19
.44 .32 .41 .56 1.48 .33 1.06 .75
SGV 7 / 16 UNF – 06 – JIC 3 / 8 – F/M
3 / 4 – 16 UNF
14.5 10.8 10.5 16.7 48.7 8.5 27 22
.57 .43 .41 .66 1.92 .33 1.06 .87
SGV 7 / 16 UNF – 08 – JIC 1 / 2 – F/M
1- 1 21.0 15.5 14 21.9 51.5 13.5 31.5 31.5
/ 16 – 12 UNF
.83 .61 .55 .86 2.03 .53 1.24 1.24
SGV 7 / 16 UNF – 12 – JIC 3 / 4 – F/M
27.5 21.3 15.3 23.3 57.0 14.8 38 38
1- 5 / 16 – 12 UNF
1.08 .84 .60 .92 2.24 .58 1.50 1.50
SGV 7 / 16 UNF – 16 – JIC 1 – F/M
Order Code Including Test Point
including SMK 20- 7 / 16 UNF-VE – C6F
including SKK20- 7 / 16 UNF-VE – C6F
SMK 20 – 04- JIC 1 / 4 – F/M-1137
SKK 20 – 04- JIC 1 / 4 – F/M-1137
SMK 20 – 06- JIC 3 / 8 – F/M-1137
SKK 20 – 06- JIC 3 / 8 – F/M-1137
SMK 20 – 08- JIC 1 / 2 – F/M-1137
SKK 20 – 08- JIC 1 / 2 – F/M-1137
Other threads available on request.
T7