City of Forest Park Starr Park Outdoor Pool Bid Specification for Pool ...

Recommendations

Info

c. Occupation Safety and Health Administration (OSHA) d. ASTM e. All national codes including Building, Plumbing, Electrical, Mechanical PART 2 – MATERIALS/EXECUTION 101 – RE-PLASTERING 1. Pool will be drained by owner. 2. The Contractor will perform a sound test of entire pool for any delaminated plaster. All delaminated areas will be marked. 3. If the recommended plaster for removal exceeds 250 square feet, the Contractor will supply a line item cost to demo and repair excess delaminated plaster. The line item cost will be based on a per square foot. 4. Once the Owner approves what will be removed, the following will be done: The area slated for removal will be saw cut then chiseled out and voided areas filled with plaster. 5. Saw cut out any cracks in the pool and apply deck-o-seal or equal epoxy material. 6. All fitting shall be removed. 7. Saw cut under and around main drains, returns and skimmers. 8. Scarify the pool surface and prep for adhesive. 9. Apply a dash coat with cement glue additive to insure plaster will adhere to old. 10. Apply white plaster mix (minimum 3/8” thick) and trowel to a smooth finish. Plaster mix will be a 3 to 5 ratio, Portland to pool mix marble. 11. Furnish and install threaded: floor inlets, wall returns and skimmer equalizers lines fittings with new fittings that are NSF approved and VGB compliant. 102.1 – REMOVAL & INSTALLATION OF WATER LINE TILE 1. Remove all water line tile. 2. Dispose off site. 3. Repair any sections behind tile that is delaminated. 4. Brown coat to level with Portland Cement. 5. Install new 6”x6” chemical resistant frost proof water line tile. Color chosen by Owner. 6. Install depth markers as required by Code.
7. Grout in new tile. 8. Saw cut the coping and install a bead of caulk. 9. Coping cut shall be made through the full thickness of the deck slab. 10. Cut shall be pressure washed and allowed to dry before caulk (vulchem 116 or equal) is applied. 11. Water line tile will be done before re-plastering of pool. 102.2 – EXPANSION JOINTS IN POOL 1. Remove all existing expansion joint tile. 2. Remove all of the backer rod and or filler material. 3. Furnish and install rod and tile with new tile 4”x4” that is chemical resistant, frost proof and is non-skid ceramic tile. Color – black. 102.3 – STAIR TRIM TILE 1. Furnish and replace stair trim tile with new tile that is chemical resistant, frost proof and non-skid tile – color to be chosen by Owner. 103 – MAIN DRAIN 1. Drain grates and frames must be VGB certified and comply with ANSI/ASME A112.19.8-2007 for use in swimming pool. 2. Remove existing main drain frame and grate. 3. Verify sumps meet VGB requirements. 4. Net opening in each floor outlet covering or grating shall be at least four times the area so that maximum velocity of the water passing the grate will not exceed one and one-half feet per second (1-1/2fps) 5. Saw cut out 18’x18’ section of pool floor. Install new 18’x18’ waterway (or equivalent) grates and frame. 104 – SKIMMERS 1. Skimmers shall comply with NSF International Standard 50 and VGB compliant. 2. Saw cut deck and remove existing skimmers and piping. 3. Remove existing skimmer throats.
Page 1: City of Forest Park Starr Park Outd
Page 5 and 6: E-Verify- All Vendors must submit a
Page 7 and 8: Contractor Affidavit under O.C.G.A.

City of Forest Park Starr Park Outdoor Pool Bid Specification for Pool ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?