Heat SiPHon ® - Poolheatpumps.com

36 to 46% CO2 REDUCTION vs. GAS
FOSSIL FUEL POWER PLANT
BURNS 2.5 BTU’s
to get 1 BTU of 236 mg
ELECTRICITY
CARBON
DIOXIDE
NUCLEAR &
HYDRO-ELECTRIC
POWER PLANTS =
ZERO CO2 100% REDUCTION
HEAT SIPHON® Lasts a Lifetime
Heat SiPHon ®
Outlives Gas Heaters
NO CORROSION
Almost all gas pool heaters have a sheet metal cabinet
and a copper heat exchanger with cast iron water connections.
Usually they are assembled with galvanized steel
screws. Since gas heaters are so expensive to run, the gas
heater manufacturers all try to keep the cost of the heater
as low as possible. But metal cabinets rust and copper heat
exchangers corrode.
Heat Siphon ® 's electrically isolated Pure Titanium Heat
Exchanger, PVC cabinet and stainless steel hardware, make
it corrosion proof. Its sealed refrigeration system, weatherproof
PVC control box and totally enclosed fan motor are all
designed for years of trouble free service.
NO FLAMES
Another shortcoming of gas heaters is heat exchanger
scaling or soot deposits which drastically cut down heat
transfer efficiency. The pool water flows through small flow
channels in a gas heater and the hot combustion gas heats
the outer tube surface. The flow rate in a gas heater is critical
since too low water flow will cause boiling inside the tubes
and eventually a hard scaling deposit will block the tube and
overheat it. On the other hand, very high water flow can cause
sweating or condensation on the outside of the tube which
can lead to combustion chamber rusting or soot deposits.
Heat Siphon® uses no flame so heat transfer occurs
almost 2000°F lower in temperature than combustion
gas. Since the pool water flows on the OUTSIDE of the
Titanium tubes, heat exchanger scaling and blockage are
eliminated.
With Heat Siphon® there's no pilot light to blow out, no
flue gases, no dangerous hot surfaces, no scaling, no gas piping
to run, no unsightly gas tanks and no high fuel cost.
ONE HEAT SIPHON® couLD easily last
longER than three gAS pool heaters!!
HEAT SIPHON uses
1 BTU in ELECTRICTY
to MOVE
5 or 6 BTU’s of HEAT
from the AIR
to your POOL
NO WASTE
SET IT &
FORGET IT
SIMPLE USER FRIENDLY INTERFACE -
Digital: 2-Button “UP”/“DOWN”
Analog Models: ONE Knob
WEATHER-PROOF CONTROL Box -
Keeps Electrical Controls Dry
Clean and Easily Accessible
ALL STAINLESS STEEL HARDWARE -
Cabinet Screws, Fan Acorn Nuts
LIFETIME SOLID PVC CabINET -
Weather Resistant UV Stable
Flame Retardant Plastic
BuILT-In SERVICE PORTS -
Easy 2 screw service access door for
quick system refrigerant pressure check
GAS HEATERS
BURN 6.25 BTU’s
to get 5 BTU’s
in your pool
367 mg
CARBON
DIOXIDE
80% Efficient
20%
WASTE
HEAT
Heat SiPHon ®
Quality Features:
ALL Z-Series DIGITAL MODELS ARE WIRELESS READY
Heat SIPHon ® Z-Series Models:
Digial Interface provides the gateway to Wireless Controllers
R410A SCROLL COMPRESSOR - All Heat Siphons mde after January
1, 2010 now use R410A SCROLL compressors. Unlike conventional R22 heat
pump compressors which used a piston and two check valves to compress
refrigerant to make heat, the SCROLL compressor has a fixed scroll and an
orbiting scroll that rotate around each other to continuously and QUIETLY
compress refrigerant with NO VALVES. Advantages: SCROLL Heat
Siphons will have a higher heat output at low air temperatures, where
piston compressors heat output falls off. ABOUT 12% MORE HEAT FOR YOUR POOL
WHEN YOU NEED IT!! LESS WEAR PARTS MEANS MORE RELIABILITY.
WIRELESS
FAMI LY
SAFE - LIFETIME TITANIum HEAT EXCHANgER
Electrically Isolated from pool - NO BYPASS Req'd
Accepts FULL PUMP FLOW up to 80 GPM with only
1.5 psi pressure drop - LOWEST PUMP WORK
SIMPLE DuAL PVC PLUMBING CONNECTIONS -
1.5” Sch 40 Slip ID or
2” Male Pipe Thread OD
NO METAL HEAT SINKS BuILT-In CONDENSATION DRAIN -
1/2” Nylon Barb Fitting for 3/4" clear vinyl tubing
FOOTBALL
PVC Coated
Fan Grill
& Evaporator
Screen
Standard 3/4”
Electrical
Conduit
Fitting
EASY POWER HOOK-UP -
wires inside ready
for wire nuts
GO GREEN with HEAT SIPHON - NOW ALL Models use R410A green refrigerant
According to the US Dept of Energy (DOE), the average
US Coal Fired Electric Power Plant has a 38% conversion
efficiency. So a fossil fuel power plant will burn 2.5
BTUs of coal and generate 236mg of CO2 to get 1 BTU
of electricity. BUT with Heat Siphon - it only takes 1 BTU
of electricity to MOVE 5 to 6 BTUs of heat from the air
to your pool .
A GAS POOL HEATER must burn 6.25 to 7.5 BTUs of
natural gas to get the same 5 to 6 BTUs of heat for your
pool which creates 367 mg to 440 mg of CO2 or 36 to
46% MORE emissions than Heat Siphon!!
For MORE INFORMATON about Heat Siphon's smaller CARBON Footprint go to WWW.HEATSIPHON.COM and click on this