Instructions - Door Closer Service Company
Instructions - Door Closer Service Company
Instructions - Door Closer Service Company
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
4580 CAM DISC HANDING<br />
LOOKING AT THE EDGE OF THE DOOR, DETERMINE ON WHICH<br />
SIDE THE HANDLE OR OTHER OPERATOR IS TO BE INSTALLED.<br />
ON THIS SIDE<br />
ON THIS SIDE<br />
THE CAM DISC MUST BE<br />
HANDED AS SHOWN.<br />
THE CAM DISC MUST BE<br />
HANDED AS SHOWN.<br />
INSTRUCTIONS FOR CHANGING HAND OF 4580 CAM DISC<br />
STEP 1<br />
STEP 2<br />
STEP 3<br />
STEP 4<br />
REMOVE THE<br />
RETAINER CLIP<br />
SNAP THE RETAINER CLIP<br />
INTO THE GROOVE ON THE<br />
CAM PIVOT PIN.<br />
DO NOT REMOVE<br />
THE DRIVER PIECE<br />
PULL THE CAM PIVOT PIN OUT<br />
OF THE CAM DISC AS SHOWN.<br />
TURN THE CAM OVER AND PUSH<br />
THE CAM PIVOT PIN THRU THE<br />
CAM AND INTO THE CAM DISC<br />
AS SHOWN.<br />
ADAMS RITE MANUFACTURING COMPANY<br />
260 SANTA FE STREET, POMONA CA 91767<br />
4591 PADDLE OPERATOR<br />
80-0180-4591 REV. A ECN 10103 10/30/02 MCM 1 OF 2
STEP 1<br />
[ 31,75 ]<br />
Ø1.25<br />
+0,79<br />
STEP 2<br />
STEP 3<br />
[ 8.33 ] -0<br />
+1/32<br />
C L<br />
Ø.328 -0<br />
2 HOLES<br />
SET<br />
SCREWS<br />
INSTALLATION<br />
STEP 4<br />
REMOVE THE DOGGING<br />
SCREW WHEN USED IN<br />
PULL CONFIGURATION<br />
DRIVER EARS<br />
ESCUTCHEON<br />
ASSEMBLY<br />
CYLINDER C<br />
76.20<br />
3.000<br />
4580<br />
CAM DISC<br />
BINDER<br />
POST<br />
43.64<br />
1.718<br />
SEM SCREW<br />
LABEL<br />
LATCH<br />
CUTOUT<br />
5/16-24 NUT<br />
PIVOT PIN<br />
PADDLE ASSEMBLY<br />
SET SCREW<br />
DRIVE PLATE<br />
1. PREPARE STILE AS SHOWN.<br />
BACKSET OF<br />
DEADLATCH<br />
2. INSERT BINDER POST THRU Ø.328 HOLE IN STILE.<br />
3. SECURE BINDER POST WITH 5/16-24 NUT.<br />
1. INSTALL 4700 SERIES DEADLATCH PER<br />
MOUNTING INSTRUCTIONS.<br />
2. INSTALL 4580 CAM DISC ASSEMBLY AND<br />
SECURE WITH SET SCREW. (SEE REVERSE<br />
FOR CAM DISC HANDING)<br />
1. INSTALL ESCUTCHEON ASSEMBLY.<br />
2. USING 10-32 SEM SCREWS, SECURE<br />
ESCUTCHEON ASS'Y. TO BINDER POST.<br />
IMPORTANT<br />
TIGHTEN THESE SCREWS SECURELY.<br />
INSTRUCTIONS FOR CHANGING HAND<br />
1. INSTALL PADDLE ASS'Y. ALIGN DRIVE EARS<br />
ON PADDLE WITH SLOT IN DRIVER PLATE.<br />
2. INSTALL PIVOT PIN.<br />
3. INSTALL PIVOT PIN SET SCREW. TIGHTEN SET<br />
SCREW FLUSH WITH BOTTOM OF ESCUTCHEON.<br />
DRIVER SCREW<br />
TOP<br />
1. FIND DESIRED CONFIGURATION.<br />
2. REMOVE KEEPERS TO SEE LOCATION OF SPRINGS<br />
& DRIVER PLATE.<br />
DRIVER<br />
PLATE<br />
3. REVERSE SPRINGS & DRIVER PLATE IF NECESSARY.<br />
DRIVER<br />
SCREW<br />
DRIVER<br />
SCREW<br />
4. REMOVE DRIVER SCREW IF NECESSARY AND PLACE<br />
IN DESIRED LOCATION.<br />
5. REPLACE KEEPERS.<br />
OUTSIDE<br />
PULL TO LEFT<br />
RH<br />
PUSH TO LEFT<br />
RHR<br />
PULL TO RIGHT<br />
LH<br />
PUSH TO RIGHT<br />
LHR<br />
6. CONFIGURE CAM DISC. (SEE REVERSE)<br />
SPRING<br />
KEEPER<br />
INSIDE<br />
ADAMS RITE MANUFACTURING COMPANY<br />
260 SANTA FE STREET,<br />
POMONA CA 91767<br />
4591 PADDLE OPERATOR<br />
80-0180-4591 REV. A ECN 10103 10/30/02 MCM 2 OF 2
Change language