PercoTop 2K Acryl Soft Touch - Movac Group Limited

Technical Data Sheet
PercoTop ® 2K Acryl Soft Touch
2K MS Topcoat
Description
PercoTop 2K Acryl Soft Touch is a 2K polyurethane topcoat with soft feeling.
Composition based on acrylic resins.
Products
PercoTop ® 2K Soft Touch
CS952
CS010-CS095
CS702
CS703
CS600
CS602
PercoTop ® 2K MS Topcoat
PercoTop ® 2K Soft Touch Binder
PercoTop ® Tints
PercoTop ® Activator Fast
PercoTop ® Activator LR Fast
PercoTop ® Thinner Standard
PercoTop ® Thinner 2K
Colours
Industrial and standard colour registers.
Properties
High quality paint system for all coating jobs.
Highly chemical and weather-resistant surface.
A good scratch resistance for soft feel coating.
Substrates
Cured, solvent resistant, well preserved and scuff sanded OEM or old finish.
Primed surface.
Effective November 2010
PCTST – 1 - EN
1/5

Technical Data Sheet
PercoTop ® 2K Acryl Soft Touch
2K MS Topcoat
Surface preparation
Substrates must be free from all contaminants.
Sand surface:
a. dry with orbital sander and dust exhaust P320 - P500;
b. wet with sandpaper P600 - P800.
Degrease before recoating.
VOC value ready for use (EU Directive 1999/13/EC)
RAL 9010: 515. g/l 4:1 by volume with CS702 + 15 % CS600.
RAL 9005: 520 g/l 4:1 by volume with CS702 + 15 % CS600.
Product preparation
Thinner
Mixing ratio
CS600
CS602
Pot life at 20°C CS702/CS703
Volume
Weight
PercoTop ® 2K Soft Touch 4 4
CS702/CS703 1 1
3-4 hours
Recommended dry
film thickness
50-60 µ
Effective November 2010
PCTST – 1 - EN
2/5

Technical Data Sheet
PercoTop ® 2K Acryl Soft Touch
2K MS Topcoat
Application
Gravity feed
Suction feed
(High pressure spraying)
HVLP
(Low pressure spraying)
Airless
Airmix
Pressure pot
Membrane
pump
(High pressure spraying)
Electrostatic
Applicationvis
cosity
Thinner Spray
nozzle
Pressure Number of
coats
DIN 4 at 20°C
(s) (%) (mm) (bar)
22-25 CS702 15-20 1.4 4.0-5.0 2
CS703
22-25 CS702
CS703
30-35 CS702
CS703
22-25 CS702
CS703
15-20 1.4 2.0-2.5 2
5-10 0.23-0.28
2.0-3.0 air
Ca 100
material
15-20 1.2 2.5-3.5 air 2
1.0-2.0
material
According to the advice of the DuPont Technical Representative.
2
Effective November 2010
PCTST – 1 - EN
3/5

Technical Data Sheet
PercoTop ® 2K Acryl Soft Touch
2K MS Topcoat
Drying
Air drying at 20°C
Dust dry
Dry to handle
Dry
40 µ dry film thickness
30 min
6 hours
24-30 hours
Forced drying
Drying time
Drying temperature
Remarks
Flash time: 20 minutes.
Depending on film thickness.
35 minutes
60°C object temperature
Add CS215 to the basic paint to accelerate the drying of the product following
recommendations from the DuPont Technical Representative.
Product data
Package viscosity White: 125 ± 10 s DIN 4
Black: 100 ± 10 s DIN 4
Flash point 24°C
Solids Density Theoretical coverage Theoretical material
consumption
(at 50 µ) (at 50 µ)
Weight (%) (kg/l) (m 2 /kg) (g/m 2 )
+/- 1 +/- 0.01
White
Packaged 55.5 1.14 - -
Mixed 51.7 1.09 7.27 137.6
Black
Packaged 48.4 1.01 - -
Mixed 47.1 1.00 7.84 127.6
Effective November 2010
PCTST – 1 - EN
4/5

Technical Data Sheet
PercoTop ® 2K Acryl Soft Touch
2K MS Topcoat
Remarks
For structuring, brushing, elastifying, drying, anti-cratering: different
additives can be added. See separate info sheet and contact your DuPont
representative.
Stir mixing pastes and binders thoroughly each time before use.
Stir the mixture well after the weigh-out of the components.
Before application a colour comparison is recommended.
Storage conditions Material has to be stored at a temperature between 5°C and 35°C.
Shelf life
at 5°C to 35°C
Refer to the label on the original can.
Safety
Consult the Safety Data Sheet prior to use.
Observe the precautionary notices displayed on the container.
Information
The information provided herein corresponds to our knowledge on the subject at the date of its publication.
This information may be subject to revision as new knowledge and experience becomes available. The
data provided fall within the normal range of product properties and relate only to the specific material
designated; these data may not be valid for such material used in combination with any other materials or
additives or in any process, unless expressly indicated otherwise. The data provided should not be used to
establish specification limits or used alone as the basis of design; they are not intended to substitute for
any testing you may need to conduct to determine for yourself the suitability of a specific material for your
particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont
makes no warranties and assumes no liability in connection with any use of this information. Nothing in
this publication is to be considered as a license to operate under or a recommendation to infringe any
patent rights.
This Technical Data Sheet supersedes all previous issues.
Copyright © 2011 DuPont. All rights reserved. The DuPont Oval Logo, DuPont, The miracles of
science and all products denoted with ® or are registered trademarks or trademarks of E. I. du Pont
de Nemours and Company or its affiliates
Effective November 2010
PCTST – 1 - EN
5/5