Testing Machines and Systems for Metals
Testing Machines and Systems for Metals
Testing Machines and Systems for Metals
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Portal system<br />
The portal system is based on the<br />
same three-axis principle as the<br />
light portal system, but is designed<br />
<strong>for</strong> a considerably greater specimen<br />
weight. It is supplied in two designs:<br />
with electro-mechanical drive <strong>and</strong><br />
shelf magazine<br />
with pneumatic drive <strong>and</strong> belt<br />
magazine.<br />
Specimen h<strong>and</strong>ling systems<br />
Data technology<br />
In all systems, specimen data<br />
<strong>and</strong> test results are printed out<br />
<strong>and</strong> stored, or transmitted via an<br />
interface or a local PC network to<br />
a higher-order computer system,<br />
<strong>for</strong> the production of certificates<br />
<strong>and</strong> <strong>for</strong> production control.<br />
Automated hardness<br />
testing<br />
Application<br />
For automatic hardness tests,<br />
a hardness testing device <strong>for</strong><br />
Rockwell HR15T, HR30T, HR45T,<br />
HRF, HRB, HRC is coupled with<br />
automatic specimen h<strong>and</strong>ling of<br />
the X-linear system.<br />
Characteristic, feature Clip on X-Linear Polar Light portal Portal<br />
system system system system system<br />
No. of storage places<br />
(St<strong>and</strong>ard)<br />
50 – 100 60 – 120 100 – 400 200 – 400 140 – 240<br />
Specimen types/ round <strong>and</strong> inherently rigid round <strong>and</strong> round <strong>and</strong> round <strong>and</strong><br />
features flat specimen, round <strong>and</strong> flat flat specimen flat specimen flat specimen<br />
wires, foils specimen from weight weight weight<br />
Specimen dimensions<br />
appr. 0.2 mm thick to 20 kg to 1 kg to 10 kg<br />
Shoulder or strip width up to 50 mm up to 35 mm up to 70 mm up to 40 mm up to 70 mm<br />
Shoulder or wire diameter up to 16 mm up to 22 mm up to 60 mm up to 18 mm up to 40 mm<br />
Thickness (st<strong>and</strong>ard) up to 5 mm up to 6/12 mm up to 60 mm up to 10 mm up to 60 mm<br />
Total length up to 350 mm up to 260 mm up to 500 mm up to 260 mm up to 500 mm<br />
(variabel) 1)2) (variabel 2) via (variabel via (variabel via (variabel via<br />
magazine inserts) magazine inserts) magazine inserts) mag. limit stops)<br />
Cross section measurement<br />
Thickness or diameter thickn. o. inq.. ✓ ✓ ✓ ✓<br />
Width - ✓ ✓ ✓ with centering5) No. of measur. levels/spec. 1 1/3 1/3 1/3 1/3<br />
Specimen disposal back to the back to the to various to various to various<br />
storage place3) storage place4) bins4) bins4) bins4) (hardness testing)<br />
Specimen identification<br />
(with Barcode)<br />
Optinal tests<br />
✓ ✓ ✓ ✓ ✓<br />
Roughness - - ✓ ✓ ✓<br />
Hardness 6) - - ✓ ✓ ✓<br />
Layer thickness - - ✓ ✓ ✓<br />
1) Through variation of the grip spacing L<br />
2) Drive-in height fixed through fixed grip, i. e. axial alignment in the magazine placement<br />
3) Not suitable <strong>for</strong> foils (not rigid). For specimens with large de<strong>for</strong>mations, only 1 part of the broken specimen is replaced in the magazine in each case<br />
4) Requires additional time expenditure. Alternative: additional disposal grippers <strong>and</strong> e. g. good/bad switch points<br />
5) In parallel length or to total length<br />
6) HR15T, HR30T, HR45T, HRB with automatic range changing, e. g. dependent on the specimen thickness previously<br />
25