DH100ACDCI Ionization Air Duct Smoke Detector - System Sensor ...

Figure 7. System wiring diagram for 4-wire duct smoke detectors:
CAUTION
Do not loop wire under terminals when wiring detectors. Break wire runs to provide system supervision of connections.
POWER INPUTS ACCEPT
24 VDC, 24 VAC 50-60 HZ,
120 VAC 50-60 HZ, OR
220/240 VAC 50-60 HZ.
CONNECT POWER SOURCE
TO APPROPRIATE TERMINALS
OF EACH DETECTOR.
AVAILABLE POWER INPUTS
9 10 A B C
24V
120
VAC
220/240
VAC
AVAILABLE POWER INPUTS
9 10 A B C
24V
120
VAC
220/240
VAC
CONNECT POWER SOURCE
TO APPROPRIATE TERMINALS
OF EACH DETECTOR. SEE
SPECIFICATIONS FOR
ADDITIONAL POWER SUPPLY
INFORMATION.
AUX. CONTACT RATINGS
10A @ 30 VDC RESISTIVE
10A @ 250 VAC
100mA MINIMUM @ 5 VDC
1/4 HP @ 240 VAC
1/8 HP @ 120 VAC
NOT INTENDED FOR
CONNECTION TO CONTROL
PANELS.
TROUBLE CONTACT RATING
2.0 A @ 30 VDC resistive
2.0 A @ 125 VAC resistive
N.C.
ALARM AUXILIARY CONTACTS
FOR FAN SHUTDOWN, ETC.
16 6 17 7 18 8
C.
N.O.
N.O.
ALARM AUXILIARY CONTACTS SHOWN IN
STANDBY. CONTACTS TRANSFER DURING
ALARM AS INDICATED BY THE ARROWS.
C.
SUPERVISORY TROUBLE CONTACTS
N.C.
N.C.
ALARM AUXILIARY CONTACTS
FOR FAN SHUTDOWN, ETC.
16 6 17 7 18 8
C.
N.O.
N.O.
ALARM AUXILIARY CONTACTS SHOWN IN
STANDBY. CONTACTS TRANSFER DURING
ALARM AS INDICATED BY THE ARROWS.
C.
SUPERVISORY TROUBLE CONTACTS
14 3 14
3
N.C.
FOR WIRING OF AUXILIARY
DEVICES, REFER TO
MANUFACTURER'S
INSTALLATION INSTRUCTIONS
OR CONTACT MANUFACTURER.
NOTE: THE SUPERVISORY RELAY NOW
PROVIDES A "FORM C" CONTACT FOR
CUSTOMIZED APPLICATIONS.
FOR STANDARD APPLICATIONS, ONLY
THE "NO" CONTACT IS USED
TROUBLE CONTACTS CLOSED IN ALARM AND STANDBY.
CONTACTS OPEN WHILE DETECTOR PCB OR POWER IS
REMOVED OR WHEN TAMPER FEATURE TIMES OUT. OPEN
CONTACTS SIGNAL TROUBLE CONDITION TO PANEL.
TROUBLE CONTACTS CLOSED IN ALARM AND STANDBY.
CONTACTS OPEN WHILE DETECTOR PCB OR POWER IS
REMOVED OR WHEN TAMPER FEATURE TIMES OUT. OPEN
CONTACTS SIGNAL TROUBLE CONDITION TO PANEL.
+
5
5
ALARM
INITIATION
LOOP
–
ALARM
INITIATION
CONTACTS
4
CONTACTS SHOWN
OPEN IN STANDBY.
CONTACTS CLOSE
IN ALARM.
ALARM
INITIATION
CONTACTS
4
CONTACTS SHOWN
OPEN IN STANDBY.
CONTACTS CLOSE
IN ALARM.
UL LISTED 4-WIRE
CONTROL PANEL
FIRST DETECTOR IN THE LOOP
DH100ACDCI
LAST DETECTOR IN THE LOOP
DH100ACDCI
EOL RESISTOR
SPECIFIED BY
PANEL MANUFACTURER
H0182-00
Figure 8. Wiring diagram for DH100ACDCI to APA451:
Figure 9. Wiring diagram for DH100ACDCI to
RTS451KEY:
DH100ACDCI
Alarm Signal 15
Aux. Power + 19
Sup. N. O. 14
APA451
2 Alarm
3 Power
DH100ACDCI
Alarm Signal
Aux. Power +
Sup. N. O.
15
19
14
1
RTS451/RTS451KEY
*
(Red LED) Alarm
For RTS451KEY
only without a
control panel.
*
Sup. COM
NOTE:
Aux. Power –
3
20 1
Common
Wiring diagram shown is for DH100ACDCI 4-wire duct
smoke detector system equipped without a control panel.
Sup. COM
Aux. Power –
Reset
3
20
2
6
2
3
(Green LED)
Power
NOTE:
A trouble condition is indicated when the green LED
is not illuminated.
Test
11
4
5
Figure 10. Multiple fan shutdown (interconnect):
1 6
12 16
FAN
CONTROL
H0155-01
A B C
DETECTOR 1
SYSTEM
CONTROL
POWER OR
THERMOSTAT
1 6
12 16
FAN
CONTROL
A B C
DETECTOR 2
SYSTEM
CONTROL
POWER OR
THERMOSTAT
OUT TO
10 DETECTORS
MAXIMUM
1 6
12 16
FAN
CONTROL
A B C
DETECTOR 10
SYSTEM
CONTROL
POWER OR
THERMOSTAT
Important Interconnect Notes
• When using the interconnect feature, all interconnected
units must be powered with the
same, independent supply.
• Polarity must be maintained throughout the
interconnect wiring. Connect terminal 12 on unit
1 to terminal 12 on unit 2 and so on. Similarly,
connect terminal 1 on unit 1 to terminal 1 on
unit 2 and so on.
• Up to 10 units may be interconnected.
D100-68-00 6 I56-1684-06R