Silentblocs and Bushes

Silentblocs and BushesRenault, HyundaiPulling Device for silentblocs with Hydraulic Cylinder 17 tSuitable for Renault Laguna II rear sub frame.This tool enables the quick and safe removal and replacement of silentblocs onthe rear sub-frame. Even severely corroded silentblocs can be pressed out andreplaced within a few minutes by using this tool. Using the fixing unit ensures anaccurate alignment of the silentbloc into the prescribed correct position.Specification: KL-1210-30 Pulling device for silentblocs with hydr. cyl.Part No. Description Qty.KL-0040-2500 Hydraulic cylinder 17t 1KL-0039-1003 Retainer adaptor for hydr. cyl. with O-ring 1KL-1210-300 Pulling device without hydr. cyl. 1Scope of Delivery: KL-1210-300 Pulling device f. silentbl. without hydr. cyl.Part No. Description Qty.KL-0039-1002 Retainer adaptor for clamp nut and pressure spindle with O-ring 1KL-0039-1912 Pull Spindle M12, with Nut 1KL-1210-301 Fixing unit 1KL-1210-302 Sleeve set 1Scope of Delivery: KL-1210-301 Fixing unitArtikel-Nr Beschreibung MengeKL-1210-3011 Mounting rod 1KL-1210-3012 Fixing rod 2KL-1210-3013 Socket pin Ø14,5 / Ø12 mm 1KL-1210-3014 Adjusting washer 15x21x1 1KL-0040-2511 Cylinder bolt M8 x 16 4KL-0205-2018 Circlip ring A14 1Scope of Delivery: KL-1210-302 Sleeve SetPart No. Description Qty.KL-1210-3021 Support sleeve long, Ø 88 mm 1KL-1210-3022 Press piece Ø 76 mm 1KL-1210-3023 Support sleeve Ø 88 mm 1KL-1210-30KL-1210-300KL-1210-301KL-1210-302KL-1210-30Pulling Device for Silentblocs, with Hydraulic Cylinder 17 t(German Utility Model)KL-1810-01Suitable for Hyundai Tucson front axle carrier.The pulling device KL-1810-01 used in conjunction with a hydraulic pump suchas the KL-0215-35 M25 ,enables the removal and replacement of the silentblocs(separately available as Hyundai Original-spare part no. 624862E000) on thefront axle carrier. The replacement of silentblocs can be carried out directly onthe vehicle within a few minutes without having to remove or replace the frontaxle carrier. Even very tight-fitting or severely corroded silentblocs are not anissue by using the 17 t hydraulic cylinder KL-0040-2500.Advantages: Quick - Substantial time savings of up to 3 hours Removal of front axle carrier not necessary. Hammers, chisels etc. are not required.KL-1810-01KL-1810-010KL-1810-011Technical Data:Weight:11 kgScope of Delivery: KL-1810-01 Pulling Device f. silentblocs, with hydr. cyl.Part No. Description Qty.KL-1810-011 Pulling device for silentblocs without hydraulic cylinder 1KL-0040-2500 Hydraulic cylinder 17t 1Scope of Delivery: KL-1810-011 Pulling Device f. Silent. without Hydr. Cyl.Part No. Description Qty.KL-1810-010 Pulling device for silentblocs, without hydr. cyl. and without ad. 1KL-0039-1003 Retainer adaptor for hydraulic cylinder with O-ring 1Scope of Delivery: KL-1810-010 Pulling device for silentblocwithout hydr. cyl., without adaptorPart No. Description Qty.KL-1810-0101 Press piece 1KL-1810-0102 Support sleeve 1KL-1810-0103 Clamping housing 1KL-1810-0104 Screw 1KL-1810-0105 Mandrel 1KL-1810-0106 Support ring 1KL-0039-1686 Press-/Support sleeve, short, Ø 86 mm 1KL-0039-1914 Pull spindle M14, with nut 1Copyright KLANN-Spezial-Werkzeugbau-GmbH, Germany - 6.E1(179)4-57