Metric Catalogue - SEF meccanotecnica

More documents

Recommendations

Info

Process For Successful Deep Hole Drilling:Series 2XDCE Technical Information1. Start by producing a 1.5 x diameter to 3 x diameter pilot holeusing a coolant or non-coolant pilot drill. Typically this tool willhave a point angle the same as or greater than the deep holedrill. Run this drill at 100% of the final drill speed and 1/2 theDrill shouldnot makecontact hereDrill shouldmake contactherenormal IPM.2. Retract and tool change to the final deep hole(2XDCE MA Ford ® Series) drill.3. Rapid to clearance plane and enter the pilot hole at 25% (don’t exceed 400 to 500 RPM) of the final speedand 25 - 50 mm/min. This will help with true position by eliminating drill whip. Once into the hole, turn on thecoolant and advance to the material start. At this point, you can add a dwell to clear any chips that have beenleft from the previous drill and let the spindle get to full speed. Increase the speed and feed to final drillingparameters.4. Drill one shot to the final hole depth or through.5. Should you experience any squeaking you may need to retract the drill and increase your feed. Chip packing isoccurring and will need to be addressed.6. Once through the material, it may be necessary to reduce the RPM to eliminate breakage of the drill due to drillwhip. Then retract to the clearance plane.Machine RequirementsHigh Pressure Pump System (70 Bar)Machine runout of 0.008mm Max.Due to the conditions of equipment, tool holders,and conditions beyond MA Ford ® ’s control, yourresults may vary.Should your application require more in depthdiscussion or a special tool, please contactM.A. Ford ® ’s Application Engineering Departmentat +44(0) 1332 267960.Safety NoteAlways wear the appropriate personal protective equipmentsuch as safety glasses and protective clothing when usingsolid carbide or HSS cutting tools. Machines should be fullyguarded. Technical data provided should be consideredadvisory only as variations may be necessary depending onthe particular application.84www.maford.com email: sales@mafordeurope.com Tel:+44(0) 1332 267960 Fax:+44(0) 1332 267969
Series 2XDCE Recommended cutting dataWorkpiece materialSPEEDVc-M/MinDiameter3 4 5 6 7 8 9 10 12FEED MM/REVLow Carbon Steel
Page 1:
High Performance ToolsMetric Catalo
Page 4 and 5:
Series 113A ,177, 178, 179, 180 & 2
Page 6 and 7:
Series 177Tool No.EDPD1 (Tol h10)D2
Page 8 and 9:
Series 177STool No.EDPD1(Tol h10)D2
Page 10 and 11:
Series 277BLAZETool No. D1 (Tol h10
Page 12 and 13:
Series 178RTool No. EDP D1 (Tol h10
Page 14 and 15:
Series 180RBLAZEL2D2D1L1RTool No. E
Page 16 and 17:
Features / Caractéristique134 Seri
Page 18 and 19:
Series 134Tool No. EDP D1 D2 L1 L2P
Page 21 and 22:
P76Series 135N3Tool No. EDP D1 Tol
Page 23 and 24:
P76Series 135N5Tool No. EDP D1 Tol
Page 25 and 26:
P76P76Series 135B-N3Tool No.EDP D1
Page 27 and 28:
P77Tool No.UncoatedEDPSeries 138Too
Page 29 and 30:
P77P77Series 138BTool No. EDP D1 To
Page 31 and 32:
Contents Vue d’EnsembleSeries1561
Page 33 and 34:
DM Series 156Z2P7912°Tool No.EDPAL
Page 35 and 36: DM Series 157Z MultiP7945°ALtima
Page 37 and 38: Material cross reference chartTOOL
Page 39 and 40: ContentsVue d’EnsembleTechnical I
Page 41 and 42: P822XDSSMMetric No. EDP D1 (Tol h7)
Page 43 and 44: P822XDSSMMetric No. EDP D1 (Tol h7)
Page 45 and 46: P822XDCSMMetric No. EDP D1 (Tol h7)
Page 47 and 48: P822XDSRMMetric No. EDP D1 (Tol h7)
Page 49 and 50: P822XDSRMMetric No. EDP D1 (Tol h7)
Page 51 and 52: P822XDCRMMetric No. EDP D1 (Tol h7)
Page 53 and 54: P822XDCLMMetric No. EDP D1 (Tol h7)
Page 55 and 56: P822XDCLMMetric No. EDP D1 (Tol h7)
Page 57 and 58: P842XDCEMMetric No. EDP D1 h7 D2 h6
Page 59 and 60: 200AP86BLAZE45-65RcTool No. EDP D L
Page 61 and 62: 200AP86BLAZE45-65RcTool No. EDP D L
Page 63 and 64: 205BP86BLAZEL 2L 1Tool No. EDP D L1
Page 65 and 66: 205BP86BLAZEL 2L 1Tool No. EDP D L1
Page 67 and 68: P87207L 2L 1Tool No. EDP D L1 L2207
Page 69 and 70: Series 229P87Tool No. EDP D1 Tol m7
Page 71 and 72: Technical SectionPageSeries 113A Re
Page 73 and 74: Series 177, 178 & 179 Recommended c
Page 75 and 76: Series 180 Recommended cutting data
Page 77 and 78: Series 277 Recommended cutting data
Page 79 and 80: Recommended cutting data - Al / Al-
Page 81 and 82: DM Series 156 Recommended cutting d
Page 84 and 85: Recommended speed - all drillsRecom
Page 88 and 89: Series 200A Recommended cutting dat
Page 90 and 91: Material cross reference chartUK Ge
Page 96 and 97: Optimised Cutting-High Performance
Page 98 and 99: M.A. FORD Quality PolicyUltimately
Page 100: SEF MECCANOTECNICASEDEVia degli Ore
show all

Metric Catalogue - SEF meccanotecnica

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?