IN100 7900 Mortise Lock Door Manufacturers Template

.2349 METAL DOOR1.2502.7504.563SECTION A-AC L OF BEVELC L OF BEVEL2.750 TYP. BACKSETFROM C L OF BEVEL55HINGEEDGE5HINGEEDGE5.750 2.750HINGEEDGE1.000 THRU2X #12-24 TAPPED HOLE92X.375 THRU3.8751.250THIS SIDE ONLYOPTION ASEE TABLEC L OF POCKETC3.250L OF STRIKE3.6254.000.3756.500MIN.7.250±.005+.0318.000 - .00010.5009.1257.0004.62510WIREACCESS.750THIS SIDE ONLY.500THIS SIDE ONLYOPTION BSEE TABLE6 C L OF LEVERS2.4691.7971.125 THRU2X .625AA38" (REF) AFF(36" (REF) AFFFOR ADA)2X.250 THRU4.563±.031MORTISE POCKETFROM C L OF BEVELOUTSIDEFINISHEDFLOOR+.0311.250 - .000BEVEL SIDE1.250 MIN. CUTOUTIN REINFORCEMENT2X .422INSIDEOUTSIDEINSIDEL.H. DOORR.H. DOORNOTES:1. DRAWING IS NOT TO SCALE.2. PREPARATION DETAILS ARE IN SUPPLEMENT TO ANSI/BHMA A156.115AND/OR A115W.3. REFERENCE STRIKE TEMPLATE FOR DETAILS TO PREPARE FRAME.3.3505O/S TRIM53.250AUTHORIZED PREFIXESC24.5.6.7.8.9.10.11.12.13.FOR ELECTROLYNX APPLICATIONS, REFER TO MCKINNEY TRANSFER DEVICECATALOG.VERTICAL CENTERLINE IS REFERENCED FROM THE CENTERLINE OF THE BEVEL.(INDUSTRY STANDARD BEVEL IS 1/8 INCH IN 2 INCHES.)CONSULT THE AUTHORITY HAVING JURISDICTION (AHJ) TO VERIFY THERECOMMENDED MOUNTING HEIGHT ABOVE THE FINISHED FLOOR (AFF).LIMITATIONS IN THE DOOR CONSTRUCTION PROCESS MAY REQUIRE SOMEHOLES TO BE FIELD-LOCATED USING THE PHYSICAL PART AS A TEMPLATE.STANDARD TOLERANCE OF ± .015 APPLIES TO ALL DOOR PREPARATIONREQUIREMENTS, UNLESS OTHERWISE SPECIFIED.DOOR REINFORCEMENT IS RECOMMENDED TO IMPROVE (SURFACEMOUNTED) FASTENER HOLDING POWER AND CRUSH RESISTANCE (WHENTHRU-BOLTING IS EMPLOYED). CONSTRUCTION TECHNIQUES SHOULD REFLECTINDUSTRY BEST PRACTICES (I.E. WDMA, SDI) AND AUTHORIZED METHODSWHERE LABEL SERVICE (I.E. UL, W-H) IS IN EFFECT.WIRE RACEWAY AREAS SHOULD BE FREE OF OBSTRUCTIONS & SHARP EDGESTO PROTECT WIRES FROM CUTS & ABRASIONS.CAREFULLY NOTE WHICH FEATURES ARE OPTIONAL, (WHETHER THE FEATUREAPPLIES TO BOTH SIDES OF THE DOOR AND/OR IF A DEPTH APPLIES.)MAXIMUM PRODUCT DIMENSIONS ARE SHOWN FOR THE PURPOSE OFVERIFYING FITMENT WITH DOOR FRAME STOPS, DOOR STILE SIZE &LIGHT/LOUVER KITS.IF OPTIONAL LEVERS OR ROSES ARE USED REFERENCE THE RELATED PRODUCTDIMENSIONS TO VERIFY THE FITMENT REQUIREMENTS.11.3006.450O/S LEVEROUTSIDE L.H.TRIM SHOWN 12 13C L OF STRIKEI/S TRIMC L OF LOCKBODYC L OF LEVERS 6INSIDE L.H.TRIM SHOWN 12 1311.250I/S LEVERBACKSET DEFINITIONBACKSETTOP OF DOORVERTICAL C LOPTIONS TABLEOPTION DESCRIPTIONUSED FOR FUNCTIONS79276 79277 79278 79279A CYLINDER X - X -B THUMB TURN X X - -C L OFBEVELDOOR HANDINGL.H. INSIDE R.H.L.H.R.B.DOOR MANUFACTURERS TEMPLATE:INCEPTA SERIES TRIMMETAL DOOR7900 MORTISE LOCKSHEET 1 OF 2OUTSIDEINSIDEOUTSIDER.H.R.BSargent Manufacturing Company100 Sargent Drive New Haven, CT 06511RELEASE DATE01-NOV-11TEMPLATE NO.4697 A

WOOD DOOR+.025.218 - .0001.2504.563SECTION A-A2.750C L OF BEVELC L OF BEVEL2.750 TYP. BACKSETFROM C L OF BEVEL55HINGEEDGE55HINGEEDGEHINGEEDGE.375 2.7501.000 THRU2X .125 1.0002X.375 THRU3.8751.250 .875THIS SIDE ONLYOPTION ASEE TABLEC L OF POCKETC L OF STRIKE.3752X R.5634.0003.2503.625+.0636.500 - .0007.250+.0318.000 - .00010.5009.1257.0004.625.750 .875THIS SIDE ONLY.500 .875THIS SIDE ONLYOPTION BSEE TABLE6 C L OF LEVERS2.4691.7971.125 THRU2X .625AA38" (REF) AFF(36" (REF) AFFFOR ADA)2X.250 THRU4.563±.031MORTISE POCKETFROM C L OF BEVELOUTSIDEFINISHEDFLOOR+.0311.250 - .000BEVEL SIDE+.0001.125 - .0632X .422INSIDEOUTSIDEINSIDEL.H. DOORR.H. DOORNOTES:1. DRAWING IS NOT TO SCALE.2. PREPARATION DETAILS ARE IN SUPPLEMENT TO ANSI/BHMA A156.115AND/OR A115W.3. REFERENCE STRIKE TEMPLATE FOR DETAILS TO PREPARE FRAME.4.5.6.7.8.9.10.11.12.13.FOR ELECTROLYNX APPLICATIONS, REFER TO MCKINNEY TRANSFER DEVICECATALOG.VERTICAL CENTERLINE IS REFERENCED FROM THE CENTERLINE OF THE BEVEL.(INDUSTRY STANDARD BEVEL IS 1/8 INCH IN 2 INCHES.)CONSULT THE AUTHORITY HAVING JURISDICTION (AHJ) TO VERIFY THERECOMMENDED MOUNTING HEIGHT ABOVE THE FINISHED FLOOR (AFF).LIMITATIONS IN THE DOOR CONSTRUCTION PROCESS MAY REQUIRE SOMEHOLES TO BE FIELD-LOCATED USING THE PHYSICAL PART AS A TEMPLATE.STANDARD TOLERANCE OF ± .015 APPLIES TO ALL DOOR PREPARATIONREQUIREMENTS, UNLESS OTHERWISE SPECIFIED.DOOR REINFORCEMENT IS RECOMMENDED TO IMPROVE (SURFACEMOUNTED) FASTENER HOLDING POWER AND CRUSH RESISTANCE (WHENTHRU-BOLTING IS EMPLOYED). CONSTRUCTION TECHNIQUES SHOULD REFLECTINDUSTRY BEST PRACTICES (I.E. WDMA, SDI) AND AUTHORIZED METHODSWHERE LABEL SERVICE (I.E. UL, W-H) IS IN EFFECT.WIRE RACEWAY AREAS SHOULD BE FREE OF OBSTRUCTIONS & SHARP EDGESTO PROTECT WIRES FROM CUTS & ABRASIONS.CAREFULLY NOTE WHICH FEATURES ARE OPTIONAL, (WHETHER THE FEATUREAPPLIES TO BOTH SIDES OF THE DOOR AND/OR IF A DEPTH APPLIES.)MAXIMUM PRODUCT DIMENSIONS ARE SHOWN FOR THE PURPOSE OFVERIFYING FITMENT WITH DOOR FRAME STOPS, DOOR STILE SIZE &LIGHT/LOUVER KITS.IF OPTIONAL LEVERS OR ROSES ARE USED REFERENCE THE RELATED PRODUCTDIMENSIONS TO VERIFY THE FITMENT REQUIREMENTS.11.3006.450O/S LEVER3.350OUTSIDE L.H.TRIM SHOWN 12 135O/S TRIMC L OF STRIKEI/S TRIMC L OF LOCKBODYC L OF LEVERS 653.250INSIDE L.H.TRIM SHOWN 12 1311.250I/S LEVERBACKSET DEFINITIONBACKSETTOP OF DOORVERTICAL C LC L OFBEVELAUTHORIZED PREFIXESC2OPTIONS TABLEOPTION DESCRIPTIONUSED FOR FUNCTIONS79276 79277 79278 79279A CYLINDER X - X -B THUMB TURN X X - -DOOR HANDINGL.H. INSIDE R.H.L.H.R.B.DOOR MANUFACTURERS TEMPLATE:INCEPTA SERIES TRIMWOOD DOOR7900 MORTISE LOCKSHEET 2 OF 2OUTSIDEINSIDEOUTSIDER.H.R.BSargent Manufacturing Company100 Sargent Drive New Haven, CT 06511RELEASE DATE01-NOV-11TEMPLATE NO.4697 A