Aluminium Oxide 9µ thru 100µ ULTRALAP-MicroFinishing Film
Aluminium Oxide 9µ thru 100µ ULTRALAP-MicroFinishing Film
Aluminium Oxide 9µ thru 100µ ULTRALAP-MicroFinishing Film
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Material Safety Data Sheet<br />
Supfina Grieshaber GmbH & Co. KG<br />
Greulingstrasse 33<br />
42859 Remscheid, Germany<br />
Tel.: +49(0)2191-3713-0<br />
Fax: +49(0)2191-3713-657<br />
Informing department: Technical Sales Department<br />
Emergency information: see above<br />
Data sheet for BAFF<br />
<strong>Aluminium</strong> <strong>Oxide</strong> <strong>9µ</strong> <strong>thru</strong> <strong>100µ</strong><br />
<strong>ULTRALAP</strong>-<strong>MicroFinishing</strong> <strong>Film</strong><br />
Generic Description: Precision Coated Al203 Abrasive on Mylar Polyester <strong>Film</strong> w/Q-<br />
Back Anti-Slip backing.<br />
1. General Information<br />
Chemical Name & Synonyms: Precision Graded <strong>Aluminium</strong> <strong>Oxide</strong> Grain and Epoxy Resin<br />
coated on Polyester <strong>Film</strong> with Q-Back anti-Slip backing.<br />
Chemical Family: Proprietary blend of AI203and Resin coated onto<br />
polyester substrate<br />
DOT Shipping Name: Coated Abrasive (Sandpaper)<br />
DOT Hazard Classification: Not Regulated<br />
Trade Names and Synonyms: UMFF Ultralap Micro Finishing <strong>Film</strong>.<br />
Generic Composition: 1. Al203 Abrasive Grain<br />
2. Proprietary Resin<br />
3. Polyester <strong>Film</strong><br />
2. Hazardous Ingredients<br />
None<br />
- 1 -
Material Safety Data Sheet<br />
3. Physical Date<br />
Boiling Point: N/A<br />
Vapor Pressure: N/A<br />
Vapor Density: N/A<br />
Solubility in Water : N/A<br />
Appearance and Odor: White Al203 Coating on Polyester <strong>Film</strong>, Trace Epoxy<br />
Odor.<br />
4. Fire and Explosion Data<br />
Flash Point: > 300 Degrees F.<br />
Flammable Limits: LEL-Not Determined<br />
UEL-Note Determined<br />
Extinguishing Media: Water, CO2, or Foam<br />
Special Firefighting Procedures: None Required<br />
Unusual Fire and Explosion Harzards: None<br />
Auto Ignition Temperature: Not Determined<br />
5. Health Hazard Data<br />
TLV: Not Applicable<br />
Effects of Overexposure: None Determined<br />
Chronic Hazards: None Determined<br />
OSHA Exposure Limits: 20 mpcf (5mg/m 3 ) Respirable Dust ( 8 Hr. TWA)<br />
TLV-10mg/m 3 Total Dust<br />
Note: <strong>ULTRALAP</strong>-Micro Finishing <strong>Film</strong> may produce dust<br />
when used.<br />
Exposure Analysis Method : NIOSH Manual of Analytical Methods<br />
6. Reactivity Data<br />
Stable Material; Upon ignition will decomposes into oxides of carbon (CO, CO2, etc.)<br />
7. Special Protection<br />
None Required<br />
8. Special Precautions<br />
As with any coated abrasive product, always practice safe and hygienic habits such as<br />
washing with soap and water after use. Product is abrasive; do not rub or contact with<br />
hands or face.<br />
Do not take internally. Avoid direct contact with open flame. Store in a cool dry place with<br />
With a temperature of between 45 degrees F. and 85 degrees F.; and, a relative humidity<br />
between 0% and 30%<br />
The given particulars are based on our present knowledge and experiences.<br />
However, a legally binding guarantee of certain cannot derived from our statements.<br />
- 2 -<br />
Issue 01.03.2008
Change language