Lighting - Custom Bikes by Mike

Taillights & License Plate Kits‘Radius’ Side Mount Brake Caliperand Taillight/License Plate Mountsby Paul Yaffe OriginalsContoured to conform to the wheel and brake rotor on theright-side of your bike for a totally custom look. Chrome billetaluminum caliper mount and license plate frame have hi-Intensity LED taillights. Smooth design features hiddenmounting hardware and special channels milled into thebracket to hide wiring. For use with 18" wheelsONLY and RevTech ® or PM 4-piston calipers and7"-wide x 4"-tall license plates. . . . . . . . . . .$789.9947642 For Softail ® models from 1986 thru 1999(right-side mount)47644 For FXR models 1984 thru 1994 (rightsidemount)47643 For custom rigid frames with 111/2" rearrotors (right-side mount)Universal Taillight/License Plate MountSimilar to the kits above but without the integral caliper mount. Mountsto the left-side on most models and clears the 70-tooth belt pulley.47645 Complete kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$789.9947647 Billet clamp for 1"-diameter frame tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$132.9947648 Billet clamp for 11/8"-diameter frame tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$132.99Note: Installation of these accessories may be in violation of FMVSS Standard #108476424764447642ApparelBike Kits& TrailersSeats& BagsFootControlsHandControlsLightingElectrical‘The Answer’ LED OvalTaillight byPaul Yaffe OriginalsFeatures raw aluminum billet bezelthat is designed for a flawless flushmount installation. Can be lit withthe outer ring, center ring or bothat the same time! This permits manyturn signal and brake light combinations.Works with hard saddlebags,fenders and other custom applications.Made in USA. Sold each.47691 Large Answer LED lamp(measures approximately8" x 5") . . . . . . . . . . . .$299.9947697 Small Answer LED lamp(measures approximately4.75" x 3.5") . . . . . . . .$286.99Note: Bolts must be trimmed foryour application.‘Soon-2B-Copied’ Sidemount License Plate Frameby Paul Yaffe OriginalsSketched on a cocktail napkin during a plane ride home from the Indyshow, Paul Yaffe came up with the most radical sidemount design he hadever conceived. It’s filled with dozens of super bright LED’s and even hasthe exclusive strobing brake light for safety. Works with all PYO verticalsidemount brackets. Machined from 6061-T6 billet aluminum and thenflawlessly chrome-plated. Mounting brackets sold separately. . . . . . . .$407.99600041 Sidemount license plate frameUniversal Flat SurfaceMount by Paul YaffeOriginalsOriginally designed for the PYO‘Phantom’ frame because therewasn’t anywhere to install oneof our traditional sidemountbrackets on such an exoticframe. Requires two 1/4" x 20holes to be drilled and tappedand will work with any of ourvertical sidemounts. Machinedfrom 6061-T6 billet aluminumand chrome-plated. Mountinghardware included. . . . . . .$96.99600042 Flat surface mountLaydown Tubing Mountsbracketby Paul Yaffe OriginalsAn addition to the sidemount bracket collection, this laydown configurationfits 1" or 11/8"-diameter tubing. Created for use on the swingarm sectionof hardtail or Softail ® models, this “drill-and-mount” bracket reallyrakes the plate holders to almost parallel to the tube it’s mounted on.Works great with ‘Soncy’ sidemount or with any Paul Yaffe vertical plateholders. Requires drilling and tapping of two 1/4" x 20 holes. Machinedfrom 6061-T6 billet aluminum and then chrome-plated for quality.600043 For 1" tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$96.99600044 For 11/8" tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$96.99For the Dealer Nearest You, Call: 800-729-33325.23ExhaustIntakeEngineGasketsTranny& ClutchDrivelineWheels,Tires& BrakesFramesForks& ShocksSheetmetalGeneralCrossReference