catalog #81 (4 MB) - Forster Products

More documents

Recommendations

Info

Bench Rest ® Seater DiesRELOADINGBENCH REST ® SEATER DIESFeatures Innovative, caliber-specific Die Chamber (Fig. 6) holds thesupporting the entire outside diameter of the sized case ratherthan just the bullet and case neck. (Most competitor productssupport only the case rim.) Non-crimping style provides accuracy, consistency andperfect alignment. (Exception: 30-30 caliber die does crimp.) Seating stems supplied with our standard seaters match evenspecial bullet needs such as those encountered during theFig. 6 shows how both thebullet and the entire case areheld in perfect alignment whilethe bullet is seated.Fig. 6DieChamber(P-30)The secret to perfect alignment is holding the bullet, case andseating stem in the same close fitting chamber for the entireseating operation.Die withEntry Die ChamberDie Ready toSeat BulletBench Rest ® Seater DieFirst die of its kind on the market and is stillthe best straight line Seater Die available.Featurealignment while the bullet is seated.Ordering InformationBench Rest Seater Dies are available inmore than 70 calibers, either individuallyor as a set.Ordering information begins on page 32.Fig. 7 shows how thebullet is held in the sameclose fitting chamber forits entire length.Fig. 8 shows the positionof the sliding die chamber(P-30) after the bullet hasbeen seated.Fig. 7 Fig. 8DieChamber(P-30)Die with Bullet and CaseHeld in Perfect AlignmentDie withSeated BulletBench Rest ® Ultra MicrometerSeater DieFine adjustments for precise seatingmeasurements the very first time.Ordering Informationare available in more than 70 calibers,either individually or as a set.Ordering information begins on page 32.Our Customers SayYour dies work better at seating straight than any other make.West Monroe, LAFeaturesoriginal Bench Rest Seater Die plus an ultra accuratemicrometer for adjusting bullet seating depth.adjustable to .0005". Index marks at increments of .001" areclearly marked.and measured it, simply adjust the micrometer stem down tothe desired depth and the cartridge will be exactly the lengthyou need. Fine tuning of your rounds to bring them out closeto the lands of your rifling is simple.with seating accurate rounds.30 forsterproducts.com
Bench Rest ® Rifle Reloading Die ToolsRELOADINGCross Bolt Die Lock RingClamps around the entire die, resulting in a more precisemating of the lock ring threads to the die threads.DIE-G-10FeaturesEasy to use cross bolt connects the two ends of the ringinstead of a traditional screw design that tightens directlyinto the threads of the die, resulting in a more precisemating of the lock ring threads to the die threads.Provides a more reliable alignment with no canting, and nodamage to the die threads which remain undamaged.Standard equipment on all Forster Products high qualitySizing and Seater Dies.Tightening or loosening the steel cross bolt screw requiresOrder No.DIE-G-10DescriptionCross Bolt Die Lock Ring (single ring)Cross Bolt Die Lock Ring (pack of one dozen)Stuck Case RemoverThe easy way to remove the Decapping Rod andExpander Ball when a case is stuck in the Die.FeaturesDesigned for use with Forster Sizing Dies which feature theAssembly.threaded spindles.All components hardened for long life.Washer protects the top of your die.SC1000Product in UseOrder No.SC1000DescriptionStuck Case RemoverOversize “E-Z” Out Expander Balls forour Bench Rest® Sizing DiesOversize “E-Z” Out Expander Ballshown on Spindle (not included)Oversize “E-Z” OutExpander Ball6-40 internal thread.204" Bullet Dia. .224" Bullet Dia. .243" Bullet Dia.Order No. Order No. Order No.E-10-2040 E-10-2240 E-10-2430E-10-2045 E-10-2245 E-10-2435E-10-2050 E-10-2250 E-10-244010-32 internal thread.264" Bullet Dia. .284" Bullet Dia. .308" Bullet Dia.Order No. Order No. Order No.E-10-2640 E-10-2645 E-10-2650 E-10-3090Order No. is actual diameter. For example, Order No. E-10-2045 is anTipTo keep the inside of your Dies scratch-free, ensure the outside and inside of your cases are free of powder residue and other debris, casethat result from trimming and deburring, or a case that has not been deburred, are especially damaging to die interiors. These chips canbecome embedded in the die interior. The resulting brass against brass effect “galls” or wears away minute pieces of brass on the case,and gets worse with each use of the die.forsterproducts.com31
Page 1: Reloading & Gunsmithing ToolsStraig
Page 5 and 6: Case Trimmer!RELOADINGSTEP 2. Choos
Page 7 and 8: Case TrimmersRELOADINGOriginal and
Page 9 and 10: Case Trimmer Collets and PilotsRELO
Page 11 and 12: Case Trimmer Collet and Pilot Order
Page 13 and 14: Case Trimmer AccessoriesRELOADINGOu
Page 15 and 16: Case Trimmer AccessoriesRELOADINGPr
Page 17 and 18: Stand Alone Case Conditioning Acces
Page 19 and 20: Co-Ax ® PressRELOADINGFeaturesThe
Page 21 and 22: Co-Ax ® Press AccessoriesRELOADING
Page 23 and 24: Co-Ax ® Case and Cartridge Inspect
Page 25 and 26: Datum Dial Ammunition Measurement S
Page 27 and 28: Bench Rest ® Rifle Reloading DiesR
Page 29: Bench Rest ® Sizing DiesRELOADINGB
Page 33 and 34: Bench Rest ® Sizing and Seater Die
Page 35 and 36: Bullet PullersRELOADINGStandard and
Page 38 and 39: Headspace GagesGUNSMITHINGHeadspace
Page 40 and 41: Headspace GagesGUNSMITHINGTable 10.
Page 42 and 43: Headspace GagesGUNSMITHINGTable 11.
Page 44 and 45: ScrewsGUNSMITHINGTrigger Guard Scre
Page 46 and 47: ORDERING INFORMATIONWe recommend us
Page 48: PRSRT-STDU.S. POSTAGEPAIDPermit No.

catalog #81 (4 MB) - Forster Products

Create successful ePaper yourself

Delete template?

Save as template?