Power and Performance - Tsubaki Europe

More documents

Recommendations

Info

TSUBAKI Supplemental ProductsCam Clutches Back StopsTSUBAKI Cam Clutch - Mining Line UpMG SeriesA proven field performer used on the intermediate shaft or pulley head on small dischargeconveyors and transfer conveyor chutes.This rugged model comes in either grease or oil filled configurations to suit your needs withseries of different sealing and operating conditions.Typical applications are small discharge conveyors and gearbox backstoppingTorque Arms for Cam ClutchesTorque arms stop the rotation of the outer race. A variety of torque arms are available for BSand other series of Cam Clutches. Please consult your local Tsubakimoto representative tofind a appropriate torque arm for your application.Special Design Versions AvailableBS220TA ~ BS450TABR SeriesThis unique product incorporates a very special design to lift off and no contact with the Innerand Outer race is possible when in the over running operation. This is due to centrifugal forceand is the reason why this type of Cam Clutch is known as a Lift Off Type.Suitable for “Overrunning high-speed inner race/low speed engaged outer race” or“Backstopping-high speed inner race overrunning”Typical applications are dewatering pumps and filtration pumpsDouble Camcage model(BS160WHSBS350WHS)(BS160WBS350W)BS-HS series MA modelBS SeriesA proven field performer for low speed high torque applications. TSUBAKI has developed aCam Clutch that has Instantaneous Hold Back, Low Noise, Easier Maintenance, Longest Lifeand Compactness.This product is ideally situated on the head shaft pulley to prevent any roll back of theconveyor if power failure or system failure occurs.Typical applications are Incline and Decline conveyor assembliesA Double Cam Cage is a standard specification in BS425HS andBS450HS.If the conveyor needs higher torque capacity in Cam Clutch sizesBS85 to BS350 and BS160HS to BS350HS, this can be achieved byadding another cam cage to the design to provide the requiredbackstop holding capacity. Please contact your local Tsubakimotorepresentative for more details.The special flanges mounted on both sides the MA type Cam Clutchallow for easy replacement of previous units. Also, to reduce costs,this Cam Clutch as been designed to be used with the previoustorque arm as is.BS-HS SeriesSafety CoversThe next generation in Cam Clutch design that takes the best of all our designs and suits theapplications with higher speeds then suited to our BS series and require greater loads. Ournew design incorporates a Cam Cage with a full compliment of cams and bearing supportedraces to give optimum load capacities and running performance.With a design that often allows for one size down selection compared to our BS series, this unit isthe leading edge product.Typical applications are the new super conveyor systems with large loads and high speeds.Cam CageSafety covers for Cam Clutches are available. These safety covers protect the unit whilepreventing hands, clothes, etc, from getting entangled in the rotating portion of the CamClutch. The safety cover shown here is for the BS Cam Clutch.CAM CLUTCHES BACK STOPS4950
TSUBAKI Supplemental ProductsTSUBAKI POWER CYLINDERSWhat are Power Cylinders ?There are three categories of linear actuators: the hydraulic cylinder, the pneumaticcylinder, and the electro mechanical cylinder which is a POWER CYLINDER.Following is a spec and cost comparison table for those three cylinders.* One financial unit is equal to 1TSUBAKI Power Cylinder Pneumatic Cylinder Hydraulic CylinderTypeThrust loadStrokeSpeedCylinder costSystem costElectricity expenseCO2 emissionLPTB1000HSL Bore size 200mm Bore size 50mm1,000kg 1,000kg 1,000kg300mm 300mm 300mm120mm/sec 120mm/sec 120mm/sec0.4 0.12.5 1.51*18 618 6This is depending on the conditions of operation and the applications.Power Cylinder T SeriesThrust force: 2.45kN { 250kgf } ~ 313kN { 32000kgf }Power CylindersTSUBAKI Power Cylinders are a completelyself-contained, motorized linear actuator unitwhich comes in a variety of types withdifferent speeds. Their compact size andease of installation make them ideallysuited to a variety of mining applications.These units require little maintenance, theyare mainly used outdoors where there is arequirement for linear motion, such as flopgates, opening and closing of roof and doors,coal sampling units and trouser, leg chutes,and clam shell for Reclaimer Tunnels,TSUBAKI Power Cylinders consists of anenclosed electric motor fitted with a DCbrake rated 150% load capacity, overtravel protection and load limiting frictiondiscs. It uses a gear set, ball screw and nutto extend and retract the rod end.As a standard for tropical applications wecan have the unit painted with a rubberizedpaint and all non load bearings screws andfasteners supplied in stainless steel.Applications for Power Cylinders arecommonly found in mines, power stations,ports and any application where a selfcontained linear actuator with no leakyreservoir, hoses, tube fittings etc areneeded to operate this unit.As well as being extremely sturdy, thePower Cylinder has either Trunnion orClevis mounting arrangements, and can befitted with stroke limit switches, rotaryencoder, potentiometer, bellows and otheraccessories. See pg.53-54 for more details.TSUBAKI Power Cylinders lend themselvesto convenient operation from remotelocations such as from another building.This is a large thrust type Power Cylinder which can be used with AC power source.The Power Cylinder T series can be used across a wide range of applications such asmining, steel, cement, injection molding machines, liquid crystal and semiconductor device.This Power Cylinder can be used outdoors. (IP55) (Higher ratings avaliable upon request)Two Easy-to Select typesThe T series has two types of safety mechanisms which are different from each other. The TBtype incorporates a slipping clutch and electric Shock Relay. The TC type is equipped with athrust detection limit switch, for press stopping.Wide VariationA wide range of models are available as standard according to application, thrust and speed.Thrust force can be selected from a range of 2.45kN { 250kgf } to313kN { 32000kgf } and speed can be selected in a range from10mm/sec to 120mm/sec.Reliable OperationAll models adopt a highly efficient ball screw, silent gear, and highlyreliable brake motor. All series incorporate a highly reliable safety devicewhich is effective against overload.Abundance of OptionsThe stroke adjusting limit switch includes the external and built-in type,and the stroke sensor includes the potentiometer, the rotary encoder,or both.Endrod DamperThese are an optional unit designed to take vibration away from cylinders.POWER CYLINDERS5152
Page 3 and 4: TSUBAKI PROFILETSUBAKI TechnologyTe
Page 6: TSUBAKI PROFILETSUBAKIGlobal Networ
Page 13 and 14: TSUBAKI Surface MiningStack Reclaim
Page 15 and 16: TSUBAKI Surface MiningRS ® Roller
Page 17 and 18: When desired material deposits are
Page 19 and 20: TSUBAKI Underground MiningTSUBAKI S
Page 21 and 22: TSUBAKI Underground MiningONE -TOUC
Page 23 and 24: TSUBAKI Supplemental ProductsSprock
Page 25: TSUBAKI Supplemental ProductsTSUBAK
Page 29 and 30: Contacts UsIndex Table of Appicatio

Power and Performance - Tsubaki Europe

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?