HiRel Space Guide (Rev. A)

TI Space ProductsComponents for Extreme EnvironmentsAmplifiers and LinearClocksData ConvertersDSPInterfaceLogicMemoryPowerwww.ti.com/space2H 2013

Space Products GuideOverview/Table of ContentsTI-HiRel Space ProductsTo support the demanding nature of space applications TI andNational have combined product lines to create a strong andunited offering for space applications. Customers can expect nodisruption of service as a result of this merger and that TI/Nationalproducts will continue to be available. By combining our portfolioswe provide a complete signal chain solution for space.National customers can be assured:• No Obsolescence• No Part Number Changes• No Requalification• Continued new product developmentPotential applications:• Commercial and defensespace-based systems• Data processing• Flight critical control systems• Gas chromatographs• Particle detectors• Photometers• Space-based imaging and surveillance• Spectrometers• Wave analyzersFor more information onTI-HiRel space products, seewww.ti.com/space.Radiation Data is available atwww.ti.com/radiation.Radiation EffectsHigh-energy protons, electrons and charged particles in naturalspace environments can strongly affect the operation of electroniccircuits used in space applications.Radiation is energy in transit, taking the form of high-speedparticles and electromagnetic waves. We encounter electromagneticwaves every day. They make up our visible light, radio andtelevision waves, ultraviolet (UV) light and microwaves with alarge spectrum of energies. These examples of electromagneticwaves do not cause ionizations of atoms because they do notcarry enough energy to separate molecules or remove electronsfrom atoms.Ionizing radiation is radiation with enough energy so that duringan interaction with an atom, it can remove tightly bound electronsfrom their orbits, causing the atom to become charged or ionized.Examples are gamma rays, protons and neutrons.Table of Contents2-3 OverviewFeatured Products4 Power6 DSP7 Memory7 Data Converters11 Precision Amplifier11 Analog Front End12 Interface13 Clocks14 Low Dose Rate Tested Analog ProductsSelection Tables14 Low Dose Rate Tested Analog Products15 Power Management17 Amplifiers and Linear20 Data Converteres20 Interface21 Clocks/Buffers21 Memory21 Logic21 Digital Signal Processor22-23 Radiation Tolerant Die Products24 ResourcesThe most common radiation requirement in the aerospace designcommunity is total ionizing dose (TID), also known as total dose.Total dose irradiation is primarily caused by electrons and protonsthat penetrate into the silicon and can result in device degradationand/or device failure.Charge buildup affects the current-voltage characteristics of transistorsused in semiconductor circuits. Proper operation of a transistorrelies on the ability to switch it from a low-conductance (off)state to a high-conductance (on) state as the gate voltage passesthrough a threshold. Extended exposure to radiation can shiftthe threshold voltages making the transistors easier or harder toswitch. Radiation may also increase the leakage current, causingthe on and off states of the transistors to become less distinguishable.Either effect can ultimately cause circuit failure.HiRel performs total dose testing on space-qualified, QML Class-Vnew product releases in order to determine how much radiationour devices can absorb before device degradation occurs. The testresults for select devices are available at www.ti.com/radiation.2 | Space Products Guide 2013 Texas Instruments

Space Products GuideOverviewRadiation EffectsAlthough TID is typically the first step indetermining the radiation tolerance of adevice to be used in the space industry,single event effects, or SEE, rank as thenext concern for space system designers.The first “must have” is that thedevice must be free of single event latchup(SEL). SEL can lead to severe disruptionor even catastrophic device failurein the system. Once a devices latches, itcan sometimes be recovered by poweringdown the system and/or performinga system reset. If left unchecked, theincreased supply current demand canlead to device burnout. One approachto making a device SEL free, is to use asemiconductor process that is inherentlySEL free. TI’s complementary bipolar(BiCOM) processes are manufacturedusing “silicon over insulator,” deep-trenchisolated wafer construction techniquesthat result in devices that are inherentlyimmune to latch-up.Once a device has been checked to beSEL free, the device will need to be ratedas to it’s single event upset or “SEU”tolerance. As charged particles passthrough the silicon, they deposit enoughenergy to cause logical errors to occur indigital devices. This so called bit flipping,i.e. a “1” to “0” state, or “0” to “1” state,can propagate into multiple bit errors, or“MBU’s” and the logic error propagatesthrough the system. Often a system mayhang-up from these unexpected logicstate changes, and may require a devicereset, or restart. Unlike the SEL, SEU’scan often be tolerated to some extent,and are classified as errors in time. Theactual SEU rate, or so called Soft ErrorRate (SER) is determined by deviceexposure to heavy ion’s at various energylevels ( LET ) over time, and determiningthe number of errors that occur. This datacan be used to generate a Weibull distributionof the error rate.Radiation Test MethodTo assure reliable performance underthe aforementioned environmentalconditions, the HiRel space productline is thoroughly tested for radiationperformance as part of the qualificationprocess. The flow diagram shownhere illustrates the HiRel radiation testprocedure.The devices are electrically tested beforeirradiation, with parametrics recordedand datalogged for later comparison.Devices are electrically biased in specializedfixtures within the radiation chamberand exposed to a predeterminedradiation level. They are then electricallyPWMControllerH.S. Op-AmpH.S. Op-AmpPrecisionOp-AmpPowerFETHigh SpeedDACHigh SpeedADCMUXRadiation test methodIncrementDosePoint ofLoadPowerFPGASRAMtested after irradiation to determineif degradation or device failure hasoccurred. If no measurable degradationhas occurred, the devices are irradiatedagain at a higher dose level and testedonce more. This process repeats untilthe devices fail or reach the maximumpredetermined radiation level.NoClockingDSPLow SpeedADCStartPre-radmeasurementsRecord DataIrradiate sample underbias conditionsSpaceLogicSERDESMotorControllerRecord DataDevice FailureEndYesSwitchRepeaterDriverPowerFETs orBITsTI Space SolutionsTI has radiation-tolerant, hermetically packaged devices released for each one of thered blocks shown in the block diagram.Texas Instruments Space Products Guide 2013 | 3

Featured ProductsPower Management1.5-7 V IN , 3A Ultra Low Dropout RegulatorTPS7H1101-SPThe TPS7H1x01 is an ultra low dropout (LDO) linear regulator that uses a PMOS passelement configuration. The TPS7H1x01 operates under wide range of input voltage,from 1.5 V to 7 V which enables 6-V IN to 5-V OUT or 1.5-V IN to 1.2-V OUT voltage conversionwhile offering excellent PSRR.The TPS7H1x01 is ideally suited for high reliability applications. It features a veryprecise and programmable fold back current limit implementation with a very wideadjustment range. This product is pending qualification to both QML class V and hightemperature standards to address the specific requirements of both environments.To support complex requirements of FPGAs or DSPs, TPS7H1x01 provides programmableSoftStart and PowerGood output for easy power sequencing. TPS7H1x01 isavailable in a thermally enhanced16-pin ceramic flatpack package.Key Features• Wide V IN Range: 1.5 V-7 V• Stable with ceramic output capacitor• ±2% accuracy• Programmable SoftStart• PowerGood output• Low dropout voltage:200 mV at 3 A (25°C)61 mV at 1 A (25°C)• Current sharing capable to support upto 6 A• Excellent thermal performance• 5962-1320201VXC pendingVINRpgPG CompSS LDO1FBPCL CSRd RdCcompRdOptionalRtRbCoutVoutRLoadRadiation Performance• TID = 100 kRAD (Si)• ELDRS free to 100 kRAD(Si) at10 mRAD/sec. exposure rate• Single event latchup (SEL) immune atLET ≤ 85 MeV-cm 2 /mg• SEB and SEGR immune atLET ≤ 85 MeV-cm 2 /mgCssVINCS PCLCompSS LDO2FB PGRpgCcompRtCoutRbTPS7H1101-SP Functional diagramGet more information: www.ti.com/product/TPS7H1101-SP4 | Space Products Guide 2013 Texas Instruments

Featured ProductsPower Management3- 6.3 V IN , 6A Point-of-Load RegulatorTPS50601-SPThe TPS50601-SP is an integrated FET Point-of-Load regulator. 3 V–6.3 V Input, 6 Asynchronous POL stepdown SWIFT DC-DC Converter that has been designed andqualified for harsh environments such as down hole drilling, geological explorationand space. This product is qualified to both QML Class V and High Temp standards toaddress the specific requirements of both environments.Efficiency (p.u.)CssR RTVINCinC2SIMPLIFIED SCHEMATICR3C1PVINVINTPS50601BOOTENPHPWRGDSYNCVSENSESS/TRRTCOMP GNDThermalPadSimplified schematicCbootLoCoEfficiency vs. Load Current V IN=5 VVOUT1.000.950.900.850.800.750.700.650.600.550.500.450.400.350.300.250.200.150.100.050.000.00 1.00 2.00 3.00 4.00 5.00 6.00IL-Load Current-AV O=3.3 VR1R2V O=1.2 VKey Features• 6 A output current• Peak efficiency: 95% (V out = 3.3 V)• Single-supply operation above 3 V IN• Split power-rail 1.6 V to 6.3 V PV IN• Min output voltage to 0.8 V• Integrated high-side and low-sidepower MOSFETs• External sync capability from 100 kHzto 1 MHz• Supported by TI’s SwitcherProdesign software tool• Parallel operation 180° out of Φ withsync pin (Ideal for driving power railswith up to 12 A requirements)• Adjustable switching frequency100-kHz to 1-MHz adjustable internaloscillatorAllows designers to select desiredexternal capacitor and inductorcomponent sizesEliminates “Spurious Noise” in theoperating bandwidth of interest• Dynamic bias feature – Improves loadtransient response with smaller outputcapacitances• Thermally enhanced 20-pin HKHceramic dual flat-pack package –saves valuable PCB space• Orderable as 5962-1022101VSC,100kRad RHA certification (pending)Radiation Performance:• TID = 100 kRAD (Si)• Single Event Latchup (SEL) immuneat LET ≤ 85MeV-cm 2 /mg• ELDRS Free• Visit www.ti.com/radiation for detailedrad reportsVery efficient DC-DC conversion at 95% at 1 amp.Get more information: www.ti.com/product/TPS50601-SPSmall form factor reference designavailable.Texas Instruments Space Products Guide 2013 | 5

Featured ProductsPower ManagementPrecision Micropower Shunt Voltage ReferenceLM4050QML-SP1.2 V and 3.3 V IN In QualificationLM4050QML-SPR SV RV SI Q+ I LI LI QTypical application circuitKey Features• Radiation performanceLow dose rate qualified to100 kRAD (Si)Single-event latchup-free up to120 MeV-cm 2 /mg• Fixed reverse breakdown voltages of2.5 V and 5.0 V• Voltage tolerance ± 0.1%• Tempco 17 ppm/˚C• 60 µA to 15 mA operating current range• SET free with 60 µF capacitor• QML-V RHA qualified, SMD5962R09235• Applications• For use in space-critical applications,such as satellite control systems andinstrumentation• Power supply for micropower dataconvertersGet more information: www.ti.com/product/LM4050QML-SPDSP32/64-Bit, 250Mhz Floating-Point DSPSMV320C6727B-SPThe SM320C6727B is the next generation of Texas Instruments’ C67x generation ofhigh-performance 32-/64-bit floating-point digital signal processor.The C67x+ CPU is an enhanced version of the C67x CPU used on the C671x DSPs.It is compatible with the C67x CPU but offers significant improvements in speed,code density, and floating-point performance per clock cycle. At 300 MHz, the CPUis capable of a maximum performance of 2400 MIPS/1800 MFLOPS by executing upto eight instructions (six of which are floating-point instructions) in parallel each cycle.The CPU natively supports 32-bit fixed-point, 32-bit single-precision floating-point, and64-bit double-precision floating-point arithmetic.256KBytesSRAM384KROM32-BitEMIFHPIInstructionCache32 KBytesC67x+DSPCoreMemory ControllerSwitchMAX MAXControldMAXConfigDMASPI 0I 2 C 0I 2 C 1McASP 0McASP 1McASP 2SPI 1RTI TimerRHA Certification PendingKey Features• New C67x+ DSP Core250 MHz; 1500 MFLOPS• Memory256 KB of SRAM and 32 KB ofI-CacheDSP/BIOS/DSPLIB/FastRTS Libraryincluded in the device• Peripherals32-bit HPI for Connecting to HostsdMAX Support for 1D, 2D, 3DTransfers as well as Multi-TapMemory DelayThree McASPsTwo I 2 C, two SPIs, 133 MHz/32-bitEMIF• Temperature Range: -55˚C to +115˚C,-55˚C to +125˚C• Available in 256-pin Ceramic QFPPackage• VelociTI Advanced Very Long InstructionWord (VLIW) ’C67x CPU Core• 5962R1023101VXC, RHA certificationpending• Orderable as SMV32OC6727BHFHWRadiation Performance:• TID = 100kRad(Si)• SEL Immune to LET = 117 MeV-cm 2 /mg• Visit www.ti.com/radiation for detailedrad reportsApplications:SMV320C6727B block diagram• SatelliteGet more information: www.ti.com/product/SMV320C6727B-SP• Radar and Guidance Systems• Geological Exploration6 | Space Products Guide 2013 Texas Instruments

Featured ProductsMemoryMonolithic Asynchronous Rad Hard 16M SRAM with Embedded EDAC and ScrubSMV512K32-SPThe SMV512K32 is a high performance asynchronous CMOS SRAM organized as524,288 words by 32-bits. It is pin selectable between two modes: master or slave.The master device selection provides user defined autonomous EDAC scrubbingoptions. The slave device selection employs a scrub on demand feature that can beinitiated by a master device.WZE1ZE2GZDQ(31:0)Data ConvertersRead/WriteCircuitA7A8A9A10A11A12A13A14A15A16EDACRow DecoderSMV512K32-SP block diagramMemory Array512K x 32I/O CircuitColumn DecoderA0 A1 A2 A3 A4 A5 A6 A17 A18MBESCRUBZBUSYZGet more information: www.ti.com/product/SMV512K32-SPKey Features• Radiation performanceTID = >300 kRAD (Si)SER < 5e-17 upsets/bit-dayProton upset saturation crosssection < 3e-16cm 2 /bitLatch up immunity > LET = 110MeV-cm 2 /mg (T=398°K)• Functionally compatible with commercial512K x 32 asynchronous 16 MbSRAMs• 20ns read, 13.8ns write-throughmaximum access time• Built-in error detection and correction(EDAC)• Built-in scrub engine for autonomouscorrection (scrub frequency and delayis user defined)• Three state bidirectional data bus• Orderable as 5962-1123701VXC12-Bit 500-MSPS Analog-to-Digital ConverterADS5463-SPThe ADS5463-SP is a 12-bit, 500-MSPS analog-to-digital converter (ADC) that operatesfrom both a 5-V supply and 3.3-V supply, providing LVDS-compatible digital outputsfrom the 3.3-V supply. The input buffer isolates the internal switching of the onboardtrack and hold from disturbing the signal source while providing a high-impedance input.A INA INV REFCLKCLKA1ReferenceTH1TimingTH2+ +A2TH3– –ADC1 DAC1 ADC25OVR OVR DRY DRYDigital Error CorrectionD[12:0]AV DDDAC2DV DDA35 5GNDADC3Key Features• Radiation performanceTID = 150 kRAD (Si)• Single event latchup (SEL) immune atLET ≤ 86 MeV-cm 2 /mg• SNR > 64.5 dBFS at 450 MHzand 500 MSPS• 2.2-VPP differential input voltage• 2.2-W total power dissipation• On-chip analog buffer, track and holdand reference circuit• 84-pin ceramic ceramic quad Flatpackpackage (HFG)• QML-V RHA qualified, SMD5962R0720802VXC• Military temperature range–55°C to 125°CADS5463-SP functional block diagramGet more information: www.ti.com/product/ADS5463-SPApplications• Orbital communication• Orbital control systems• Spacecraft communicationsTexas Instruments Space Products Guide 2013 | 7

Featured ProductsData Converters12-bit 3.2 GSPS ADC /12-bit Dual 1.6 GSPS ADCADC12D1600QML-SPV IN I+V IN I–V IN Q+V IN Q–CLK+CLK–R termR termR termMUXT/HT/HClockManagementLVDSOutputs12 1212-bit 12ADC 1:2DeMUX 12 1212-bitADC121:2DeMUX1212Control/statusand other logicControlpinsADC12D1600QML-SP block diagramSPI1212DI(11:0)DId(11:0)DCLKIORIORQDCLKQDQd(11:0)DQ(11:0)Get more information: www.ti.com/product/ADC12D1600QML-SPQMLV, RHA in QualificationKey Features• Radiation performanceSEL and SEFI immune >120MeV-cm 2 /mgTID 100 kRAD (Si)• Full power bandwidth of 2.7 GHz• 9.2/8.9 ENOB• SNR: 58.3/56.6 dB• SFDR: 67/62 dBc• 1.71 W per channel at 1 GSPS fromsingle 1.9-V supply• Low-noise deMUX’d LVDS outputs• Guaranteed no missing codes• Space qualified• Temperature range: –55°C to +125°C• Orderable as ADC12D1600CCMLSApplications• Satellite communication system• Wideband communications• Data acquisition systems• RADAR/LIDAR• Software defined radio14-Bit, 155 MSPS A/D ConverterADC14155QML-SPNarrowband Satellite ReceiverLNAVCOPLLBPFBPFBPFBPFAmpAmpAmpAmpADC14155ADC14155ADC14155ADC14155FPGA/ASICKey Features• Radiation performanceTID of 100 kRAD (Si)Single-event latchup-free up to120 MeV-cm 2 /mg• Input bandwidth of 1.1-GHz forhigh IF sampling• SFDR of 80.3 dBFS• Power consumption of 967 mW at155 MSPS• Guaranteed no missing codes• Dual 1.8-V and 3.3-V operationRx – RF ModuleApplications• For use in satellite narrowbandreceiversADC14155QML-SP functional block diagramGet more information: www.ti.com/product/ADC14155QML-SP8 | Space Products Guide 2013 Texas Instruments

Featured ProductsData Converters8-Channel, 50 kSPS to 1 MSPS, 12-Bit A/D ConverterADC128S102QML-SP12V2.2kV ZLM4050-5.0QMLVAVDADC128S102QML-SPIN0IN1SCLKIN2CSIN3DININ4IN5DOUTIN6IN7Key Features• Radiation performanceTID of 100 kRAD (Si)Single-event latchup-free up to120 MeV-cm 2 /mg• Only 2.3 mW of power consumption• SPI serialized outputs• 8 input channels• DNL -0.3 to 0.5 LSB typical• INL ± 0.6 LSB typical• QML-V RHA qualified, SMD• 962R0722701VZAApplications• Ideal for precision measurements intelemetry and control systemsTypical application diagramGet more information: www.ti.com/product/ADC128S102QML-SP12-Bit Micropower Rail-to-Rail Output D/A ConverterDAC121S101QML-SP+12V20 kΩV ZLM4050-5.0QMLDAC121S101QML-SPSYNC V OUT = 0V to 5VDINSCLKFunctional block diagramKey Features• Radiation performanceTID of 100 kRAD (Si)Single-event latchup-free up to120 MeV-cm 2 /mg• Only 0.64-mW of power• 3-wire, 20-MHz SPI digital interface• Supply range 2.7 V to 5.5 V• DNL -0.1 to 0.21 LSB• Setting time 12 µS• QML-V RHA qualified, SMD5962R0722601VZAApplications• For use in programmableprecision biasing in telemetry andcontrol systemGet more information: www.ti.com/product/DAC121S101QML-SPTexas Instruments Space Products Guide 2013 | 9

Featured ProductsData ConverterHigh-Performance, Low-Power, Dual Channel, 10-Bit 1 GSPS or Single 10-Bit 2 GSPS ADCADC10D1000QML-SPPower / Channel (w)5.04.54.03.53.02.52.01.51.1ADC10D1000QML-SP Power Consumption200 400 600 800 1000 1200 1400 1600 1800 2000 2200Sample Rate (MSPS)Competitor AKey Features• Radiation performanceTID of 100 kRAD (Si)Single-event latchup-free up to120 MeV-cm 2 /mg• Full power bandwidth of 2.8 GHz• 9 ENOB with FIN 248 MHz Fs and1 GHz sample rate• Single 1.9 V power supply• Lowest power in the industry at 1.45 Wper channel at 1 GSPS• Low noise 1:2 demuxed LVDSoutputs• Guaranteed no missing codesApplications• For use in satellite wideband softwaredefinedradios for communications,radar, and LIDARGet more information: www.ti.com/product/ADC10D1000QML-SPTexas Instruments Space Products Guide 2013 | 10

Featured ProductsPrecision AmplifierDual Channel, High-Precision, Rail-to-Rail Output OperationalLMP2012QML-SPVoltage Offset (µV)5.04.54.03.53.02.5Voltage Offset vs TemperatureTCVOS = 0.015 µV/°C2.0-55 -35 -15 5 25 45 65 85 105 125Temperature (C)Typical application diagramKey Features• TID of 50 kRAD (Si)• ELDRS qualified to 50 kRAD (Si)• Low SET cross section• Low supply current of 920 µA• Very low TCVos of 0.015 µV/ºC• Low input offset voltage of 60 µV overtime and temperature• Low 1/f noise of 35µV/√Hz• 3-MHz wide gain bandwidth• 10 pin hermetic gull wing ceramiccerpack package• QML-V RHA qualified, SMD5962L0620601VZAApplications• Ideal for use in precision measurementsin telemetry and controlsystems, as well as sensing solutionsGet more information: www.ti.com/product/LMP2012QML-SPAnalog Front EndDual-Channel, 14-Bit, 40 MSPS Analog Front End with LVDS OutputsLM98640QML-SPImage SensorCDSS/HCDSS/HFocal Plane Electronics Board++CDACFDACPGAPGAFDACCDACTiming ControlLM98640QML-SP14 bitADC14 bitADCSPISerializerImage sensor functional block diagramDigital ProcessingBoardFPGAImageProcessingFPGATimingControlKey Features• Radiation tolerant up to a totalionizing dose of 100 kRAD (Si)• Single-event latchup and SEFI-free upto 120 MeV-cm 2 /mg• Space-qualified, fully-integrated,high-performance, 14-bit, 5 to 40MSPS image-processing solution• Low power 125 mW/channel• Serialized LVDS outputs and LVDSinput clock• CDS or S/H processing with selectable0 dB or 6 dB Gain for CCD or CMOSsensors• Independent programmable gain andoffset correction for each channel• Programmable input clamp voltage• Programmable sampling edge up to1/64th pixel periodGet more information: www.ti.com/product/LM98640QML-SPApplications• Ideal for use in image processingapplications for earth observation,space imaging, and star trackers11 | Space Products Guide 2013 Texas Instruments

Featured ProductsInterfaceSerDes Interface TransceiverTLK2711-SPThe TLK2711-SP is a member of the WizardLink transceiver family of multi-gigabittransceivers, intended for use in ultra-high-speed, bidirectional, point-to-point datatransmission systems. The TLK2711-SP supports an effective serial interface speed of1.6 Gbps to 2.5 Gbps, providing up to 2 Gbps of data bandwidth. The primary applicationof this transceiver is to provide very high-speed I/O data channels for point-to-pointbaseband data transmission over controlled impedance media of approximately 50Ω.LOOPENPRBSENTXD0−TXD15TKLSBTKMSBTXCLKRKLSB18 BitRegisterTESTENENABLEPRBSEN998b/10bEncoder8b/10bEncoder2:1MUX1010MUXControls:PLL, Bias, RX,TXPRBSGenerator10102:1MUX10ClockSynthesizerInterpolator andClock RecoveryPRBSENParallel toSerial2:1MUXBIASClockTXPTXNPREKey Features• Radiation performanceTID = 25 kRAD (Si)SEL immune to 67.9 MeV-cm 2 /mg• Hot-plug protection• High-performance 68-pin ceramicquad flat pack package (HFG)• Interfaces to PCBs, copper cables orfiber-optic cable• On-chip PLL provides clock synthesisfrom low-speed reference• Receiver differential input thresholds200-mV minimum• Low power: < 500 mW• Ideal for high-speed backplane interconnectand point-to-point data link• QML-V qualified, SMD• 5962-0522101VXCApplications• Flight critical control systems• Launch vehicles• Satellite communications• Space-based imaging andsurveillanceRKMSBRXCLKRXD0−RXD1518 BitRegister99CommaDetectand 8b/10bDecodingCommaDetectand 8b/10bDecodingPRBSEN10101:2MUXPRBSVerification10Serial toParallelRecoveredClock2:1MUXDataRXPRXNSignal Detect(LOS)TLK2711-SP functional block diagramGet more information: www.ti.com/product/TLK2711-SP12 | Space Products Guide 2013 Texas Instruments

Featured ProductsClocksClock Synchronizer/Jitter CleanerCDCM7005-SPThe CDCM7005-SP high-performance, low-phase noise and low-skew clock synchronizersynchronizes a voltage-controlled crystal oscillator (VCXO) or voltage-controlledoscillator (VCO) frequency to one of two reference clocks. The CDCM7005-SP can lockto one of two reference clock inputs and supports frequency hold-over mode and fastfrequency locking for fail-safe and increased system redundancy.REF_SELPRI_REFSEC_REFCTRL_LECTRL_DATACTRL_CLKPDRESET orHOLDAutomaticLVCMOSREF_MUXVCReferenceClockFeedbackClockAVCCPECLtoLVCMOSFB_MUXMNVCC_CP10N 2 12LOCKPFDY0_MUXHOLDChargePumpCurrentReferenceLVCMOSLVPECLLVCMOSSTATUS_REF/PRI_SEC_CLKSTATUS_VCXO/I_REF_CPPLL_LOCKCP_OUTY0AY0BKey Features• Radiation performanceTID = 50 kRAD (Si)• Two reference clock inputs (primaryand secondary clock) for redundancysupport with manual or automaticselection• Accepts LVCMOS input frequencies upto 200 MHz• VCXO IN operating frequencies up to2.2 GHz (LVPECL)• Up to five differential LVPECL outputsor up to 10 LVCMOS outputs• Frequency is individually selectable oneach output• SPI-controllable device setting• 3.3-V power supply• High-performance 52-pin ceramicquad flat pack (HFG)• QML-V qualified,SMD 5962-0723001VXCVCXO_INVCXO_INVBBPECLINPUT/890 o90 oP16-DivPDividerVCC – 1.3VY3_MUXY2_MUXY1_MUXLVCMOSLVPECLLVCMOSLVCMOSLVPECLLVCMOSLVCMOSLVPECLLVCMOSLVCMOSY1AY1BY2AY2BY3AY3BY4AApplications• High-speed data acquisition andgeneration• MRI: magnetic resonance imaging• Orbital data aquisition• Satellite communications• Software defined radio (SDR)• Space-based imaging & surveillance• Spacecraft wireless infrastructure• Ultrasound system• X-ray: baggage scanner• X-ray: medicalY4_MUXLVPECLLVCMOSY4BGNDCDCM7005-SP functional block diagramGet more information: www.ti.com/product/CDCM7005-SPTexas Instruments Space Products Guide 2013 | 13

Low Dose Rate Tested Bipolar Analog ProductsIIt has been shown that for many types ofintegrated circuits, the response to totalionizing dose (TID) radiation is dependenton the dose rate. Many bipolar productshave been shown to exhibit enhanced lowdose rate sensitivity (ELDRS), where theymay pass TID testing at high dose rates,but fail at lower dose rates. TI’s bipolarprocess technology delivers superiorradiation performance and no ELDRS.For low does rate tested products, everywafer is tested and qualified at high andlow dose rates• Per Mil-Std-883 method 1019 condition D• Low dose rate of 10 mrad/s(36 rad/hr)• Biased and unbiasedInput Offset Voltage (mV)21.50.50-0.5-1-1.5-2Low Dose Rate Tested LM139ALow Dose Rate BiasedLow Dose Rate UnbiasedHigh Dose Rate BiasedHigh Dose Rate UnBiased0 20 40 60 80 100 120Exposure (krad[Si])SMD Ordering for Low Dose Rate Tested ProductsExample LM124A SMD Ordering NumberOrdering info: 5 962R 9950402 VXALevel of radiation exposureLow dose rate qualifiedSelection TablesLow Dose Rate TESTED PRODUCTSDLA Unique Low Dose Rate Certified ProductsDevice Description Part NumberELDRS-Free ProductsLM124AQML-SP W Low-power, quad operational amplifier 5962R9950402VXALM139AQML-SP Low-power, low-offset voltage quad comparator 5962R9673802VXALM117QML-SP 3-terminal adjustable regulator 5962R9951705VXALM136-2.5QML-SP 2.5 V reference diode 5962R0050102VXALM193QML-SP Low-power, low-offset voltage, dual comparator 5962R9452603VXALM111QML-SP Voltage comparator 5962R0052402VXALM158QML-SP Low-power, dual operational amplifier 5962R8771003VXALM119QML-SP High-speed, dual comparator 5962R9679802VXALM2941QML-SP 1A, low-dropout adjustable regulator 5962R9166702VXALM2940QML-SP 1A, low dropout regulator 5962R8958704VXALMP2012QML-SP Dual, high precision, rail-to-rail output op amp 5962L0620602VXALM7171QML-SP E, W High-speed, high-output voltage feedback amp 5962F9553602VXALMH6702QML-SP 1.7 GHz, ultra-low-distortion, wideband op amp 5962F0254502VXALF411QML-SP Low-offset, low-drift JFET input op amp 5962R1122201VZALow-Dose Rate Qualified ProductsLM117HVQML-SP 3-terminal adjustable regulator 5962R0722961VXALM4050QML-SP Precision micropower shunt voltage reference 5962R0923561VZAx – Indicates multiple package options available E Evaluation board W WEBENCH ® enabledIn Qualification.14 | Space Products Guide 2013 Texas Instruments

Selection TablesPower ManagementDC/DC ConverterDevice Orderable DescriptionTPS50601-SP WPE 5962-1022101VSCE Evaluation board P MPR prototype W Web Bench3-6.3 V, Monolithic 6 Abuck converterRadiationTolerance100 kRAD (TID)85MeV (SEL)Iout (A)V IN(V)Min Vout(V)Max DutyCycle (%)SwitchingFrequency (kHz)Packages6 3 to 6.3 0.8 85 100 to 1000 CFP-20PWM ControllersRadiation V IN (min) V IN (max) Duty Cycle PWM OutputsDevice Orderable DescriptionTolerace (V) (V) (Max)(%) (#) PackagesUC1825-SP 5962-8768104VEA/V2A High-speed PWM controller 40 kRAD 8.4 22 50 2 CDIP-16-, LCCC-20UC1525B-SP 5962-8951105V2A Regulating pulse-width modulator 40 kRAD 8 35 50 2 LCCC-20UC1825A-SP 5962-8768105VEA High-speed PWM controller 40 kRAD 8.4 30 50 2 CDIP-16UC1843-SP 5962-8670410VPA/V9A Current-mode PWM controller 40 kRAD 7.6 30 100 1 CDIP-8, KGDUC1843A-SP 5962-8670409VPA Current-mode PWM controller 40 kRAD 7.6 30 100 1 CDIP-8UC1846-SP 5962-8680603VEA/V2A/VFACurrent-mode PWM controller 40 kRAD 7 40 50 2 CDIP-16, LCCC-20CFP-16UC1875-SP 5962-9455502VKA/VFA Phase-shift resonant controller 50 kRAD 9.25 20 100 4 CFP-20,CDIP-20UCC1805-SP 5962-9451305VPA Low-power BiCMOS current-mode PWM — 3.6 12 50 1 CDIP-8UCC1806-SP 5962-9457501VEA/V2A Low-power, dual-output, current-mode PWM — 6.75 15 50 2 CDIP-16, LCCC-20controllerUC1823A-SP 5962-8990502VEA/V2A High-speed PWM controller — 8.4 22 100 1 CDIP-16, LCCC-20UC1842-SP 5962-8670401VPA/VXA Current-mode PWM controller — 10 30 100 1 CDIP-8, LCCC-20UC1842A-SP 5962-8670405VPA/VXA Current-mode PWM controller — 10 30 100 1 CDIP-8, LCCC-20UC1844-SP 5962-8670403VPA/VXA Current-mode PWM controller — 10 30 50 1 CDIP-8, LCCC-20UC1844A-SP 5962-8670407VPA/VXA Current-mode PWM controller — 10 30 50 1 CDIP-8, LCCC-20UC1845-SP 5962-8670404VPA/VXA Current-mode PWM controller — 7.6 30 50 1 CDIP-8, LCCC-20UC1845A-SP 5962-8670408VPA/VXA Current-mode PWM controller — 7.6 30 50 1 CDIP-8, LCCC-20UC1863-SP 5962-9203103VEA/V2A Resonant-mode power-supply controller — 7 22 50 2 CDIP-16, LCCC-20Power DriversDevice Orderable DescriptionRadiationToleraceV IN (min)(V)V IN (max)(V)Duty Cycle(Max)(%)PWM Outputs(#) PackagesUC1707-SP 5962-8761903VEA Complementary high-speed power driver 50 kRAD 1.5 5 40 2 CDIP-16UC1705-SP 5962-9579801VPA Complementary high-speed power driver w/ — 1.5 5 40 1 CDIP-8internal regulatorUC1708-SP 5962-0051401VEA/V2A Non-inverting high-speed power driver — 3 5 35 2 CDIP-16, LCCC-20UC1709-SP 5962-0151201VPA Inverting high-speed MOSFET driver — 1.5 5 40 2 CDIP-8UC1710-SP 5962-0152001VPA Complementary high-current MOSFET driver — 6 4.7 18 1 CDIP-8UC1715-SP 5962-0052102VFA Complementary switch FET drivers 50 kRAD 7 20 40 2 CFP-16Feedback Signal GeneratorDevice Orderable DescriptionRadiationToleraceOperating SupplyCurrent (mA)V IN (min)(V)V IN (max)(V)ReferenceVoltage (V) Tolerance (%) PackageUC1901-SP 5962-8944101VCA Isolated feedback generator — 5 4.5 40 1.5 1 CDIP-14LDO ControllersDevice Orderable DescriptionRadiationToleraceIdrive (Max)(mA) V O (min) (V) V IN (max) (V) PackagesUC1832-SP 5962-9326501VCA/V2A Precision low-dropout linear controller — 100 2 40 CDIP-14, LCCC-20UC1834-SP 5962-8774201VEA/V2A High-efficiency linear regulator — 200 1.5 40 CDIP-16, LCCC-20Texas Instruments Space Products Guide 2013 | 15

Selection TablesPower ManagementAnalog ControllerSupply Voltage Transconductance V REF min Vref MaxDevice Orderable Description Radiation Tolerace (Max) Amp BW (MHz) (V) (V) PackageUC19432-SP 5962-0923301VPA Precision analog controller 40 kRAD 24 V 1.5 1.295 1.305 CDIP-8Motor DriverDevice Orderable DescriptionRadiationToleranceVoltage SupplyMin (V)VoltageSupplyMax (V)OperatingSupplyCurrent(mA)Peak OutputCurrent(A)UC1637-SP 5962-8995701VSA Switched-mode controller for DC motor drive 40 kRAD 5 35 8.5 0.4 CFP-20UC1625-SP 5962-9168902VYA Space-rated brushless DC motor controller 40 kRAD 10 18 14.5 — CDIP-28PackageVoltage ReferencesDevice Orderable DescriptionLM4050QML-SP 5962R0923561VZA Precision micropowershunt voltage referenceLM4050QML-SP 5962R0923562VZA Precision micropowershunt voltage referenceLM4050QML-SP Coming Soon Precision micropowershunt voltage referenceRadiationTolerance100 kRAD,low-dose ratequalified100 kRAD,low-dose ratequalified100 kRAD,low-dose ratequalifiedInitialAccuracy(%)ReferenceVoltage (V)OutputCurrent (mA)OperatingCurrentTempcoMax (ppm)Packaging0.1 2.5 15 60 µA 17 CSOIC-100.1 5.0 15 60 µA 50 CSOIC-100.1 1.2 15 60 µA 20 CSOIC-10LM113-1QML-SP 5962-9684302VXA Precision reference — 2.0 1.22 20 0.5 mA 100 TO-46,CSOIC-10LM136-2.5QML-SP 5962R0050101VXA 2.5 V reference diode 100 kRAD 2.5 1.2 10 1 mA 20 TO46-3LM136-2.5QML-SP 5962R0050102VXA 2.5 V reference diode 100 kRAD,ELDRS-freeLM185-1.2QML-SP 5962-8759401VXA Micropower voltagereference diodeTL1431-SP 5962R9962001VPA Precision-adjustable(programmable) shuntreference2.5 2.5 10 1 mA 20 TO46-3— 1.0 1.235 20 0.01 mA 150 TO46-2,CSOIC-10100 kRAD 0.4 2.5 20 1 mA — CDIP-8x – Indicates multiple package options availableIn Qualification.Voltage RegulatorsDevice Orderable Description Radiation ToleranceOutputCurrent(mA)OutputMin (V)Input Min(V)Input Max(V)QuiescentCurrent (mA)PackagingLM723QML-SP JM38510/10201SxA Voltage regulator N/A 150 2.0 9.5 40 — CDIP, -14TO-100-10LM117QML-SP 5962R9951703VXA 3-terminal adjustable 100 kRAD 500 1.2 4.2 40 5.0 TO39-3regulatorLM117QML-SP 5962R9951705VXA 3-terminal adjustable 100 kRAD, ELDRS-free 500 1.2 4.2 40 5.0 TO39-3regulatorLM117QML-SP 5962R9951706VZA 3-terminal adjustable 100 kRAD 500 1.2 4.2 40 5.0 CSOIC-16regulatorLM117QML-SP 5962R9951707VZA 3-terminal adjustable 100 kRAD, ELDRS-free 500 1.2 4.2 40 5.0 CSOIC-16regulatorNote: All parts have adjustable output x – Indicates multiple package options available In Qualification.16 | Space Products Guide 2013 Texas Instruments

Selection TablesPower ManagementVoltage Regulators (continued)Device Orderable Description Radiation ToleranceOutputCurrent(mA)OutputMin (V)Input Min(V)Input Max(V)QuiescentCurrent (mA) PackagingLM117HVHQML-SP 5962R0722901VXA 3-terminal adjustableregulator100 kRAD 1500 1.2 4.2 40 5.0 TO39-3LM117HVHQML-SP 5962R0722961VXA 3-terminal adjustableregulatorLM117HVHQML-SP 5962R0722902VZA 3-terminal adjustableregulatorLM117HVHQML-SP 5962R0722962VZA 3-terminal adjustableregulatorLM117KQML-SP 5962R9951704VYA 3-terminal adjustableregulatorLM137QML-SP 5962P9951701VXA 3-terminal adjustableregulatorLM140JAN-SP JM38510/10706SYA Serial 3-terminalpositive regulator100 kRAD, low-dose 1500 1.2 4.2 40 5.0 TO39-3rate qualified100 kRAD 1500 1.2 4.2 40 5.0 CSOIC-16100 kRAD, low-dose 1500 1.2 4.2 40 5.0 CSOIC-16rate qualified100 kRAD 1500 1.2 4.2 40 5.0 TO-330 kRAD 1500 –37 –40 –4.2 — TO39-3N/A 1000 5.0 7.2 35 7.0 TO3-2Low Dropout Voltage Regulators (LDO)Device Orderable Description Radiation ToleranceOutputCurrent(mA)OutputMin (V)Input Min(V)Input Max(V)QuiescentCurrent (mA) PackagingLM2940QML-SP 5962R8958704VXA 1 A low dropout regulator 100 kRAD, ELDRS-free 1000 5.0 — 26 10 CSOIC-16LP2953QML-SP 5962-9233602VXA Adjustable micropowerN/A 250 1.23 –20 30 0.13 CSOIC-16low dropout regulatorTPS7H1101-SP WPE 5962-1320201VCX Wide V IN , very low droputregulator100 kRAD 3000 0.8 1.5 7.0 7.0 CFP-16Note: All parts have adjustable outputx – Indicates multiple package options availableIn Qualification.Amplifiers and LinearComparatorsDevice Orderable DescriptionRadiationToleranceResponseTime (µs)ChsSupplyVoltageRange (V)OffsetVoltage(mV)OutputCurrent(mA)PackagingLM111QML-SP 5962L0052401VXA Voltage comparator 50 kRAD 0.2, 0.1 1 5.0 to 36 3.0 50 CERDIP-8, CFP-10, CSOIC-10,TO99-8LM111QML-SP 5962R0052402VXA Voltage comparator 100 kRAD,ELDRS-freeLM119QML-SP 5962R9679801VXA High-speed,dual comparatorLM119QML-SP 5962R9679802VXA High-speed,dual comparator0.2, 0.1 1 5.0 to 36 3.0 50 CERDIP-8, CFP-10, CSOIC-10,TO99-8100 kRAD 0.05, 0.08 2 5.0 to 36 4.0 25 CERDIP-14, CFP-10, CSOIC-10,TO100-10100 kRAD,ELDRS-free0.05, 0.08 2 5.0 to 36 4.0 25 CERDIP-14, CFP-10, CSOIC-10,TO100-10LM119QML-SP 5962-9679801VXA High-speed, dual comparator 100 kRAD 0.05, 0.08 2 5.0 to 36 4.0 25 CERDIP-14, CFP-10, TO100-10LM139QML-SP 5962R9673801VXA Low-power, low-offset 100 kRAD 0.5 4 2.0 to 36 2.0 16 CERDIP-14, CFP-14, CSOIC-14voltage quad comparatorLM139QML-SP 5962R9673802VXA Low-power, low-offset 100 kRAD, 0.5 4 2.0 to 36 2.0 16 CERDIP-14, CFP-14, CSOIC-14voltage quad comparator ELDRS-freeLM139QML-SP 5962-9673801VXA Low-power, low-offset— 0.5 4 2.0 to 36 2.0 16 CFP-14, CSOIC-14voltage quad comparatorLM193QML-SP 5962R9452602VXA Low-power, low-offsetvoltage quad comparator100 kRAD 0.4 2 2.0 to 36 2.0 16 CERDIP-8, TO-99-8LM193QML-SP 5962R9452603VXA Low-power, low-offsetvoltage quad comparatorLM193QML-SP 5962-9452602VPA Low-power, low-offsetvoltage quad comparator100 kRAD 0.4 2 3.0 to 36 2.0 16 CERDIP-8, TO-99-8ELDRS-free— 0.4 2 3.0 to 36 2.0 16 CERDIP-8LM139-SP 5962-9673802VXA Quad differential comparator 50 kRAD 0.5 4 2.0 to 36 4.0 20 CDIP-14, KGDx – Indicates multiple package options available. SP is TI, QML is National.Texas Instruments Space Products Guide 2013 | 17

Selection TablesAmplifiers and LinearStandard Operational AmplifiersGainBandwidth(MHz)Device Orderable DescriptionRadiationToleranceChannelsSupplyVoltage Range (V)OffsetVoltage (mV)PackagingLM148QML-SP JM38510/11001SCA Series quad 741 op amp — 0.9 4 10 to 44 5.0 0.6 CERDIP-14LF411QML-SP 5962R1122201VZA Low-offset, low-drift JFETinput op amp100 kRAD,ELDRS-freeSupplyCurrent(mA)4.0 1 10 to 36, 44 2.0 1.8 Ceramic SOIC-10,KGDLM101AQML-SP 5962L9951501VXA Op amp 50 kRAD, 1.0 1 10 to 44 2.0 1.8 CERDIP-8,CFP-10,TO99-8LM124QML-SP 5962R9950401VXA Low-powerop ampLM124QML-SP 5962R9950402VXA Low-powerop amp100 kRAD 1.0 4 3.0 to 32 2.0 0.18 CFP-14, CSOIC-14,CERDIP-14100 kRAD,ELDRS-free1.0 4 3.0 to 32 2.0 1.8 CFP-14, CSOIC-14,CERDIP-14LM124-SP 5962-9950403VXA Quad op-amp 40 kRAD 1.2 4 3.0 to 32 1.0 0.8 CSOIC-14,KGDLM158QML-SP 5962R8771002VXA Low-power, dualop ampLM158QML-SP 5962R8771003VXA Low-power, dualop amp100 kRAD 1.0 2 3.0 to 32 2.0 0.25 CFP-8, CSOIC-10,TO99-8100 kRAD,ELDRS-free1.0 2 3.0 to 32 2.0 0.25 CFP-8, CSOIC-10,TO99-8x – Indicates multiple package options availablePrecision Operational AmplifiersDeviceOrderableRadiationToleranceTCVos(µV/°C)CMRR (dB)PSRR(dB)Voltage Noise(nV/√ — Hz)ChannelsSupply Current perChannel (mA)PackagingLMP2012QML-SP 5962L0620601VZA 50 kRAD 0.015 90 90 35 2 0.919 CSOIC-10LMP2012QML-SP 5962L0620602VZA 50 kRAD, ELDRSfreeHigh Speed Operational Amplifiers0.015 90 90 35 2 0.919 CSOIC-10Device Orderable DescriptionLM6172QML-SP 5962F9560402VXA Dual, high-speed,low-power, low-distortionvoltage feedback op ampLM6172QML-SP 5962R9560403VXA Dual, high-speed,low-power, low-distortionvoltage feedback op ampLM7171QML-SP 5962F9553601VXA Very high-speed, highoutputcurrent voltagefeedback op ampLM7171QML-SP 5962F9553602VXA Very high-speed, highoutputcurrent voltagefeedback op ampLMH6628QML-SP 5962F0254501VXA Dual, wideband,low-noise voltagefeedback op ampLMH6702QML-SP 5962F0254601VXA 1.7 GHz, ultra-lowdistortion,wideband opampLMH6702QML-SP 5962F0254602VXA 1.7 GHz, ultra-lowdistortion,wideband opampLMH6715QML-SP 5962F0254701VPA Dual, wideband videoop ampTHS4511-SP 5962-0722201VFA Wideband, fully differentialamplifier, 100 MHz, 1 chTHS4513-SP 5962-0722301VFA Wideband, fully differentialamplifier, 100 MHz, 1 chTHS4304-SP 5962-0721901VHA 1GHz wideband lownoise, 1 channelRadiationTolerance-3 dB BW(MHz)Supply VoltageRange (V)Supply Current(mA)ChannelsOffsetVoltage (mV)Packaging300 kRAD 160 5.5 to 36 2.3 2 1.5, 3 CDIP-8,CSOIC-16100 kRAD,ELDRS-free160 5.5 to 36 2.3 2 1.5, 3 CDIP-8,CSOIC-16300 kRAD 220 5.5 to 36 6.5 1 1.0 CDIP-8,CFP-10,CSOIC-10300 kRAD,ELDRS-free220 5.5 to 36 6.5 1 1.0 CDIP-8,CFP-10,CSOIC-10300 kRAD 300 5.0 to 12 9.0 2 2.0 CERDIP-8,CSOIC-10300 kRAD 1700 10 to 12 12.5 1 4.5 CERDIP-8,CSOIC-10300 kRADELDRS-free1700 10 to 12 12.5 1 4.5 CERDIP-8,CSOIC-10300 kRAD 480 10 to 12 5.8 2 6.0 CERDIP-8150 kRAD 110 5 39.2 1 4, 5.5 CFP-16150 kRAD 110 5 39.2 1 4, 5.5 CFP-16150 kRAD 110 6 18.0 1 1.0 CFP-10x – Indicates multiple package options available18 | Space Products Guide 2013 Texas Instruments

Selection TablesData ConvertersAnalog to Digital Converter (High Speed)DeviceOrderableRadiationToleranceSamplingRatePower/Channel (W)Input Bandwidth(GHz)ENOB(bits) SNR (dB) SFDR (dB) PackagingADC10D1000QML-SP E ADC10D1000CCMLS 100 kRAD 1.0 GSPS 1.45 2.8 9.0 55.6 66.7 CCGA-376ADC08D1520QML-SP E 5962F0721401VZC 300 kRAD 1.5 GSPS 1.0 2.0 7.4 47 55.5 CQFP-128ADC14155QML-SP E ADC14155W-MLS 100 kRAD 155 MSPS 0.967 1.1 11.3 70.1 82.3 CQFP-48ADS5400-SP PEADS5400MHFSV,5962-0924001VXC50 kRAD 1.0 GSPS 1.0 2.1 9.2 58 70 CQFP-100ADS5424-SP 5962-0720601VXC 100 kRAD 105 MSPS 2.0 0.570 11.5 64 65.4 CFP-52ADS5444-SP PE 5962-0720701VXC 100 kRAD 250 MSPS 2.0 0.8 11.3 6.5 60.5 CFP-84ADS5463-SP PE5962R0720802VXC, 100 kRAD 500 MSPS 1.0 2.0 9.0 62.2 51.6 CFP-845962-0720801VXCADS5474-SP 5962R1320801VXC 100 kRAD 400 MSPS 2.5 1.4 11.2 69.8 80 CFP-84E Evaluation board P MPR prototypeIn Qualification.Analog to Digital Converter (Precision Micropower)DeviceOrderableRadiationToleranceSampling RateOperatingPower (mW)Power Down(µW)InterfaceTypeSupply VoltageRange (V)PackagingADC128S102QML-SP E 5962R0722701VZA 100 kRAD 50 kSPS to 1 MSPS 2.3 0.25 Serial 2.7 to 5.25 CSOIC-16E Evaluation boardDigital to Analog Converter (Precision Mircopower)DeviceOrderableRadiationToleranceResolution(Bits)OperatingPower (mW)Power Down(µW) Interface Type INL (LSB) PackagingDAC121S101QML-SP E 5962R0722601VZA 100 kRAD 12 0.64 0.14 Serial ±2.75 CSOIC-10E Evaluation boardDigital-to-Analog Converters (High Speed)Device Orderable DescriptionDAC5670-SPDAC5675A-SP PP MPR prototype5962-0724701VXA5962-0720401VXC14-bit, 2.4-GSPS DAC with twoDAC channels14-bit, 400-MSPS DAC withone DAC channelsRadiationToleranceSample/UpdateRate (MSPS)SettlingTime (µs)SNR(dB)SFDR(dB)DNLLSBINLLSBSupplyVoltage (V)Power(mW)Packages100 kRAD 2400 0.0035 60 55 1.75 7.5 3.0, 3.6 2000 CBGA-192150 kRAD 400 0.012 67 82 2.5 4.6 3.15, 3.6 660 CFP-52Analog Front End (Imaging Systems)Device Orderable Radiation Tolerance Resolution Sample Rate PGA Range Offset DAC Range (Fine) Power PackagingLM98640QML-SP E LM98640W-MLS 100 kRAD 14 5 MHz to 40 MHz -3 dB to 18 dB ±5 mV ±122 mW/ch CQFP-68Monolithic Sample and Hold CircuitsDeviceOrderableRadiationTolerancePositive SupplyCurrent (mA)Negative SupplyCurrent (mV)Input OffsetVoltage (mV)Input BiasCurrent (nA)AcquisitionTime (µs)LF198QML-SP JM38510/12501SGA — 6.5 -6.5 5.0 75 10

Selection TablesLogicDevice Orderable DescriptionRadiationToleranceV cc /Vdd(V)I cc(mA)PackagesSN54AC14-SP 5962-8762402VDA/VCA Hex inverter Schmitt Trigger 50 kRAD 2 to 6 0.05 CDIP-14 CFPSN54AC02-SP 5962-8761203VDA Quadruple 2-input positive-NOR gates 50 kRAD 2 to 6 0.05 CDIP-14 CFPSN54AC00-SP 5962-8754903VDA/VCA Quadruple 2-input positive-NAND gates 50 kRAD 2 to 6 0.05 CDIP-14 CFPSN54AC00-SP 5962R8754903VDA/VCA RHA Quadruple 2-input positive-NAND gates 100 kRAD 2 to 6 0.05 CDIP-14 CFPSN54AC245-SP 5962R877580xVXA Octal bus transceivers with 3-state outputs 100 kRAD 2 to 6 0.05 CDIP-14 CFPSN54AC373-SP 5962R875550xVXA Octal D-type transparent latches with 3-state outputs 100 kRAD 2 to 6 0.05 CDIP-14 CFP54HC244-SP 5962-8409601VRA/VSA Octal buffer and line driver with 3-state outputs — 2 to 6 0.08 CDIP-20 CFP54HC273-SP 5962-8409901VRA/VSA Octal D-type flip-flop — 2 to 6 0.08 CDIP-20 CFP54HCT244-SP 5962-8513001VRA/VSA Octal buffer and line driver with 3-state outputs — 5 0.08 CDIP-20 CFP54LVTH244A-SP 5962-9584401V2A/VRA/VSA 3.3-V ABT 16-bit octal buffer/driver with 3-state outputs — 2.7 to 3.6 0.19 LCCC-20 CDIP CFP54LVTH162245-SP 5962-9678001VXA 3.3-V ABT 16-bit bus transceiver with 3-state outputs — 2.7 to 3.6 0.19 CFP-4854LVTH162373-SP 5962-9763801VXA 3.3-V ABT 16-bit transparent D-type latch with 3-state outputs — 2.7 to 3.6 0.19 CFP-4854LVTH162244-SP 5962-9680901VXA 3.3-V ABT 16-bit buffer/driver with 3-state outputs — 2.7 to 3.6 0.19 CFP-4854LVTH16244A-SP 5962-9668501VXA 3.3-V ABT 16-bit buffer/driver with 3-state outputs — 2.7 to 3.6 0.19 CFP-4854ALS244-SP 5962-8683901VRA/VSA Octal buffer and line driver with 3-state outputs — 5 27 CDIP-20 CFPIn QualificationDigital Signal ProcessorDevice Orderable DescriptionRadiationToleranceMFLOPSCore Supply(V)I/O Supply(V) Timers PackagesSMJ320C6701-SP 5962-9866102V VXA/VYC 140 MHz Floating-point digital signal processor 100 kRAD 1000 1.9 3.3 (2) 32-bitCFCBGA-429,FCLGA-429SMV320C6727B-SP PE 5962R1023101VXC 250 MHz Floating-point digital signal processor 100 kRAD 1500 1.2 3.3 32/64 bit CQFP-256In QualificationTexas Instruments Space Products Guide 2013 | 21

Selection TablesDie ProductsSpace-Qualified Die ProductsA wide range of die products areavailable to support our customersneeds for radiation tolerantapplications.TI offers three categories of bare diescreening:• Tested die (TD): TD is defined as 25CDC probed die that have not undergoneany special testing. Also calledbare die.• Known Good Die (KGD): KGD isdefined as die that have the samequality and reliability as the equivalentpackaged part.• Commercial wafersIf a product is available as a Space,Radiation Tolerant, or ELDRS levelpackage part, in most cases anequivalent die is also available. Visitti.com/die for a current list of availabledie and wafer products.Die Products Value AdvantageThe implementation rate of die products is rapidly increasing due to formfactor needs and system performance improvement requirements. Factorsinfluencing the migration from packaged semiconductor die to wire bonddie include:• Improved integration• Smaller size and weight• Reliability• Improved electricalperformanceRadiation-Tolerant Die Products – Cross Referencing DLA-Certified Part NumbersHigh Dose RateLow Dose RateDevice Orderable Device Orderable DescriptionLM117H MDR 5962R9951703V9A LM117H MDE 5962R9951705V9A 3-terminal adjustable regulatorLM117HVH MDR 5962R0722901V9A LM117HVH MDE 5962R0722961V9A 3-terminal adjustable regulatorLM119 MDR 5962R9679801V9A LM119 MDE 5962R9679802V9A High-speed dual comparatorLM124 MDR 5962R9950401V9A LM124 MDE 5962R9950402V9A Low-power quad operational amplifierLM136-2.5 MDR 5962R0050101V9A LM136-2.5 MDE 5962R0050102V9A 2.5V reference diodeLM139 MDR 5962R9673801V9A LM139 MDE 5962R9673802V9A Low-power, low-offset-voltage quad comparatorLM158A MDR 5962R8771002V9A LM158A MDE 5962R8771003V9A Low-power, dual operational amplifierLM193 MDR 5962R9452602V9A LM193 MDE 5962R9452603V9A Low-power, low-offset-voltage dual comparator— — LMP2012 MDE 5962L0620602V9A Precision dual operational amplifierLM2940-5.0 MDR — LM2940-5.0 MDE 5962R8958702V9A 1A fixed LDOLM2941 MDR — LM2941 MDE 5962R9166702V9A 1A adjustable LDOLM6172 MDR 5962F9560401V9A LM6172-MDE 5962R9560403V9A Dual high-speed ampLMH6715-MDR 5962F0254701V9A LMH6715-MDE — Dual wide-band videoLMP2012 MDR — LMP2012 MDE 5962L0620602V9A Dual precision rail-to-rail— — UC1843-SP 5962-8670410V9A QML class-V current-mode PWM controller— — LM124-SP 5962-9950403V9A Quadruple operational amplifier— — LM139-SP 5962-9673802V9A Quadruple differential amplifierMore radiation-tolerant and ELDRS-free products are in development.Radiation-Tolerant Tested Die for SpacePart Number Orderable DescriptionSN54AC00- DIE SN54AC00VTD1, SN54AC00VTD2 RadTolerant Class V, Quadruple 2- Input Positve- NAND GateSN54AC02- DIE SN54AC02VTD1, SN54AC02VTD2 Quadruple 2-Input Positive-NOR GatesSN54HC08- DIE SN54HC08VTDF1, SN54HC08VTDF2 Quadruple 2-Input Positive-AND GatesSN54HC273- DIE SN54HC273VTDG1, SN54HC273VTDG2 Octal D-type Flip-Flops With ClearSN54HC373- DIE SN54HC373VTDG1, SN54HC373VTDG2 Octal Transparent D-Type Latch With 3-State OutputsTL1431- DIE TL1431VTDB1, TL1431VTDB2 Precision Adjustable (Programmable) Shunt ReferenceTPS50601- DIE TPS50601TDC1, TPS50601TDC2 1.6-V to 6.3-V input, 6-A Synchronous Step Down Swift ConverterUC1825A- DIE UC1825AVTD1, UC1825AVTD2 High Speed PWM ControllerUC1825- DIE UC1825VTD1, UC1825VTD2 High Speed PWM ControllerUC1843A- DIE UC1843AVTD1, UC1843AVTD2 Current Mode PWM ControllerUC1846- DIE UC1846VTD1, UC1846VTD2 Current-Mode PWM ControllerIn QualificationPlease contact us at: diesales@list.ti.com if you require a product not currently offered in die or wafer form, TI will consider die orwafer form offerings of any package product from the broad product portfolio.22 | Space Products Guide 2013 Texas Instruments

NotesTexas Instruments Space Products Guide 2013 | 23

TI Worldwide Technical SupportInternetTI Semiconductor Product Information CenterHome Pagesupport.ti.comTI E2E Community Home Pagee2e.ti.comProduct Information CentersAmericas Phone +1(512) 434-1560Brazil Phone 0800-891-2616Mexico Phone 0800-670-7544Fax +1(972)927-6377Internet support.ti.com/sc/pic/americas.htmEurope, Middle East, and AfricaPhoneEuropean Free Call 00800-ASK-TEXAS(00800 275 83927)International +49 (0) 8161 80 2121Russian Support +7 (4) 95 98 10 701Note: The European Free Call (Toll Free) numberis not active in all countries. If you have technicaldifficulty calling the free call number, please use theinternational number above.Fax +49 (0) 8161 80 2045Internet www.ti.com/asktexasDirect Email asktexas@ti.comJapanPhone Domestic 0120-92-3326Fax International +81-3-3344-5317Domestic 0120-81-0036InternetInternational support.ti.com/sc/pic/japan.htmDomestic www.tij.co.jp/picAsiaPhoneInternational +91-80-41381665DomesticToll-Free NumberNote: Toll-free numbers do not supportmobile and IP phones.Australia 1-800-999-084China 800-820-8682Hong Kong 800-96-5941India 1-800-425-7888Indonesia 001-803-8861-1006Korea 080-551-2804Malaysia 1-800-80-3973New Zealand 0800-446-934Philippines 1-800-765-7404Singapore 800-886-1028Taiwan 0800-006800Thailand 001-800-886-0010Fax +8621-23073686Email tiasia@ti.com or ti-china@ti.comInternet support.ti.com/sc/pic/asia.htmImportant Notice: The products and services of TexasInstruments Incorporated and its subsidiaries described herein aresold subject to TI’s standard terms and conditions of sale.Customers are advised to obtain the most current and completeinformation about TI products and services before placing orders. TIassumes no liability for applications assistance, customer’sapplications or product designs, software performance, orinfringement of patents. The publication of information regardingany other company’s products or services does not constitute TI’sapproval, warranty or endorsement thereof.The platform bar and E2E are trademarks of Texas Instruments. Allother trademarks are the property of their respective owners.© 2013 Texas Instruments IncorporatedPrinted in U.S.A. by (Texoma Printing, Durant, OK)D090712