2010 Full-Line Drill Catalog - Desanto

Dx0,13Additional technical parametersThe range of drivers introduced below is availableex stock. However, it only represents a small selectionof drivers from our complete range. We naturallyDriversfor deep drilling machines1l 24also produce individual drivers of the highest precision tocustomer drawings. Attention! EB 100 requires drivers with positioninglugs. Further information on request.9form EDriversto DIN 183510form HADriversto DIN 6535d 1l 1l 1d 1l 1d 1l 1d 1d 1l 1l 1d 1l 1d 1d 1l 1l 3l 3l 1l 3l 1l 2d 1d 1l 1code no. d 1 l 1 l 2 l 31.1 10 40 24 -1.2 10 40 24 451.3 10 40 24 551.4 16 45 31,2 -1.5 25 70 34 -1.6 25 70 34 782code no. d 1 l 1 l 2 l 32.1 16 50 47 -2.2 16 50 47 552.3 16 50 47 703d 1code no. d 1 l 1 l 2 l 33.1 25 70 34 100l 2code no. d 1 l 14.1 19,05 705l 1d 1code no. d 1 l 1 l 25.1 10 60 205.2 16 80 285.3 25 100 506l 1l 2d 1code no. d 1 (inch) l 16.1 1/2 386.2 3/4 707l 1l 2d 1code no. d 1 l 19.1 8 369.2 10 409.3 12 459.4 16 489.5 20 509.6 25 569.7 32 60Driversto VDI draft12code no. d 1 l 112.1 10 6812.2 16 9012.3 25 11213Driversto Speed-Bit-Systeml 2code no. d 1 l 110.1 8 3610.2 10 4010.3 12 4510.4 16 4810.5 20 5010.6 25 5610.7 32 60811form HBcode no. d 1 l 18.1 8 368.2 10 408.3 12 458.4 16 488.5 20 508.6 25 568.7 32 608.8 40 70form HEwith code no.8.6, 8.7, 8.8code no. d 1 l 1 l 27.1 16 112 737.2 20 126 82code no. d 1 l 1 l 213.1 16 40 1613.2 25 50 25code no. d 1 l 111.1 8 3611.2 10 4011.3 12 4511.4 16 4811.5 20 50Examples for special point geometries for single-fluted gun drills(further geometries on request)with recessed coolant chamberwith chip breakerwith chip guiding step10 o15 o12 oDx0,15DD210 o30 o x1 2 o x5 5 o1 2 o5 0 o x 0 o x 7 5 o20 oDD4chip breakerSpanteilernut30 o20 o25 o12 o0,4 - 0,6 +0,05ca. 30 o30 o20 o15 o12 oDD430 o12 o20 o25 oDx0,15Dx0,05TechnicalDriver variations to suit gun drill tubesSolution for nom.-Ø < driver-Ø (difference must be appr. 6 mm):tube shank installed in driverStandardSolution for nom.-Ø ≠ driver-Ø (close to parallel):tube shank installed over spigot~ 25 mmStandard with spigotSolution for nom.-Ø > driver-Ø:tube shank installed over spigot, inside-Ø of tube shank >driver-Ø,tube shank fits against collar shoulder.~ 25 mmStandard with collarand spigot329