BULLETIN SELF-CLINCHING NUTS - Colly Components

<strong>SELF</strong>-<strong>CLINCHING</strong> <strong>NUTS</strong>STEEL, <strong>SELF</strong>-LOCKING AND NON-LOCKING <strong>NUTS</strong> - TYPES H, HN AND HNL• Meets torque requirements for IFI 100/107Grade B (unified) and ANSI B18.16.1M (metric)locknuts.• Type H is recommended for use in sheetsHRB (Rockwell “B” scale) 80 or less and HB(Hardness Brinell) 150 or less.• Type HN and HNL are recommended for use insheets HRB (Rockwell “B” scale) 60 or less andHB (Hardness Brinell) 107 or less.<strong>SELF</strong>-<strong>CLINCHING</strong> <strong>NUTS</strong>ECT 1EA A T 2C<strong>SELF</strong>-<strong>CLINCHING</strong> <strong>NUTS</strong><strong>SELF</strong>-<strong>CLINCHING</strong> <strong>NUTS</strong>TRIDENT ® LOCK<strong>NUTS</strong> - TYPE SL• 3 cycle locking performance. (1)• Recommended for use in sheets HRB (Rockwell ”B” scale) 80 or less and HB (Hardness Brinell) 150 or less.ECAll dimensions are in millimeters.METRICType T 1T 2ThreadSize x Non- Self- ThreadA(Shank) Min. SheetHole SizeIn Sheet C ENon-locking Self-locking Min. Dist.HoleC/LPitch Locking Locking (1) Code Max. Thickness +0.13 Max. ±0.25 ±0.13 ±0.25 To Edge (2)M6 x 1 NA HNL M6 1.48 1.48 8.75 8.72 12.7 5 10M8 x 1.25 NA HNL M8 1.48 1.48 10.5 10.47 14.6 6.3 11M10 x 1.5HHNHNL M10 1.48 1.48 12.7 12.67 16.5 7.9 12(1) During installation, the projections on the heads of Type HNL self-locking nuts may be flattened. This is not detrimental in any way and will notaffect self-locking or self-clinching performance.(2) To minimize sheet distortion and maximize product performance, use a centerline-to-edge value greater or equal to the value specified.NA Not Available - Use Type S instead.<strong>NUTS</strong> FOR ULTRA-THIN SHEETS - TYPE SMPSMETRICPEM TRI-DENT ®Locking FeatureAll dimensions are in millimeters.Min. Dist.ThreadAHole SizeHoleSize xIn SheetTypeThread Shank (Shank) Min. SheetC E TPitch Code Code Max. Thickness+0.08Max. ±0.25 ±0.25 To EdgeM3 x 0.5 SL M3M3.5 x 0.6 SL M3.5M4 x 0.7 SL M4M5 x 0.8 SL M5M6 x 1 SL M6M8 x 1.25 SL M81 0.98 12 1.38 1.41 0.98 12 1.38 1.41 0.98 12 1.38 1.41 0.98 14.25 4.22 6.3 1.5 4.84.75 4.73 7.1 1.5 5.65.4 5.38 7.9 2 6.92 1.38 1.46.4 6.38 8.7 2 7.11 1.38 1.42 2.21 2.31 1.38 1.42 2.21 2.38.75 8.73 11.05 4.08 8.610.5 10.47 12.65 5.47 9.7(1) Achieved using steel socket head cap screws, 180 ksi / property class 12.9 with standard finish of thermal oxide and light oil.A• Installs into sheets as thin as .025” /0.64mm.• Recommended for use in sheets HRB(Rockwell “B” scale) 70 or less and HB(Hardness Brinell) 125 or less.ECATType SMPS nuts can beinstalled closer to theedge of a sheet than nutson pages CL-4 and CL-5.All dimensions are in millimeters.Min. Dist.Thread A Hole Size HoleSize x Type Thread (Shank) Min. Sheet In Sheet C E TPitch Code Max. Thickness +0.08 Max. ±0.25 ±0.25 To EdgeM2.5 x 0.45 SMPS M2.5 0.61 0.64 3.8 3.79 5.6 1.4 3.7M3 x 0.5 SMPS M3 0.61 0.64 4.24 4.22 5.6 1.4 4.3M3.5 x 0.6 SMPS M3.5 0.61 0.64 4.75 4.73 6.4 1.4 5.1CL-6 PennEngineering • www.pemnet.com PennEngineering • www.pemnet.com CL-7