EasyMold Silicone Rubber B.pdf - Environmental Technology Inc

More documents

Recommendations

Info

Material Safety Data SheetProduct Name: EasyMold Silicone Rubber Part BProduct Codes: 33720, 33730 Revision Date: 9/17/2010Emergency overview and potential hazards:This material is not hazardous under OSHA criteria. This material is not hazardous under WHMIScriteria.Physical Hazards:Under certain conditions this material may generate flammable hydrogen gas.Acute health effects:Route of entry or possible contact: eyes, skin , ingestion .Eye contact:May cause slight eye irritation.Skin contact:No acute toxic skin effects are expected.Inhalation:Inhalation is not expected due to low vapor pressure.Ingestion:Ingestion is not expected in industrial use.Additional information on acute health effects:The health hazard evaluation is based on test results and/or on known properties of ingredients.Chronic health effects:No known or expected chronic health effects.Medical conditions which may be aggravated by exposure:None known.Target organs affected:No known internal organ effects.Signs and Symptoms of Exposure:Refer to Acute Health Effects, listed above.Carcinogens/Reproductive toxins:This material does not contain any reproductive toxins at or above OSHA or WHMIS reportable levels.This material does not contain any reportable carcinogenic ingredients. Exposure to carcinogens cannotoccur under normal conditions of use or during foreseeable emergencies.See Section 11 for Toxicological Information, if any.4. First Aid MeasuresGeneral information:Get medical attention if irritation or other symptoms occur. Before seeking medical attention removecontaminated clothing and shoes. Take a copy of the Safety Data Sheet when going for medicaltreatment.After inhalation:No special measures required.After contact with the skin:Wipe off excess material with cloth or paper. Use a waterless hand cleaner to remove as much of theremaining material as possible. Wash with soap and water.After contact with the eyes:If contact with eyes, immediately hold eyelids apart and flush with plenty of water for at least 15 min.2
Material Safety Data SheetProduct Name: EasyMold Silicone Rubber Part BProduct Codes: 33720, 33730 Revision Date: 9/17/2010After swallowing:No special treatment is required.5. Fire Fighting MeasuresFlammable properties:Method:Flash point..........................: > 300 °C (> 572 °F) (ISO 2592)Boiling point / boiling range........: not applicableLower explosion limit (LEL)..........: not applicableUpper explosion limit (UEL)..........: not applicableIgnition temperature ................: > 450 °C (> 842 °F) (DIN 51794)NFPA Hazard Class (comb./flam. liquid): IIIBFire and explosion hazards:This material does not present any unusual fire or explosion hazards.Recommended extinguishing media:Water-mist, carbon dioxide, sand, dry chemical or alcohol-resistant foam.Unsuitable extinguishing media:Water-spray, sharp water jet.Fire fighting procedures:Fire fighters should wear full protective clothing including a self-contained breathing apparatus. Coolendangered containers with water.6. Accidental Release MeasuresPrecautions:If material is released indicate risk of slipping. Do not walk through spilled material.HAZWOPER PPE Level: DContainment:Prevent material from entering surface waters, drains or sewers and soil. Contain any fluidthat runs out using suitable material (e.g. earth). Close leak if possible without risk.Spills of material which could reach surface waters must be reported to the United States CoastGuard National Response Center's toll free phone number (800) 424-8802.Methods for cleaning up:Take up mechanically and dispose of according to local/state/federal regulations. For smallamounts: Absorb with a liquid binding material such as diatomaceous earth and dispose ofaccording to local/state/federal regulations. Contain larger amounts and pump up into suitablecontainers. Clean any slippery coating that remains using a detergent / soap solution oranother biodegradable cleaner. Apply sand or other inert granular material to improve traction.7. Handling and StorageGeneral information:Always stir well before use.3
Page 4 and 5: Material Safety Data SheetProduct N
Page 6 and 7: Material Safety Data SheetProduct N
Page 8: Material Safety Data SheetProduct N

EasyMold Silicone Rubber B.pdf - Environmental Technology Inc

Create successful ePaper yourself

Delete template?

Save as template?