Automotive lifts - Heka.pl

AutomotiveliftsSupporting columns in your workshop®

monolift ME 2.0 + duolift GTE 2500 / BT 2500Single- and two-post lifts for the everyday use 2 – 2,5 ton capacitymonolift ME 2.0Specially suited for use in confined spaces and forbody work where free access to one car side is important• Lifting carriage guided inside the column• Special supporting nut made of Nylatron• Specially rolled column profile• Low pick-up height• Pick-up pads can be lowered to drive over• Optimum safey system owing to new nut assembly• Infinitely addjustable arm locks• Excellent access to car underside owing to extremelycompact lifting arms• Large accommodation range owing to optimum adjustmentof lifting armsduolift GTE 2500The standard lift with base frame• Extremely low base frame height of 45 mm• Pick-up height 105 – 165 mm,as low as 95 mm with stationary pick-up pads• Automatic arm locks• Electro-mechanical drive• Automatic lubrication of lifting spindle• Chain guide and chain fracture switch integrated in baseframeduolift BT 2500Lift with crossbeam, but without base frame, perfectlysuited for use with body repait- / straightening benches• Synchronisation via roller chain in the crossbeam• Pick-up height 105 – 165 mm,as low as 95 mm with stationary pick-up pads• Automatic arm locks• Electro-mechanical drive• Automatic lubrication of lifting spindle• Chain guide and chain fracture switch integrated in crossbeam• Low-noise automatic chain tensioning device withoutchain deflection

duolift MTF 3000 / BTE 3200 / MSE 5000Two-post lifts from 3000 to 5000 kg rated load capacityduolift MTF 3000 / MTF 3000 ETwo-post lift with two synchronised drive motors• Large lifting carriages• Elastic rolled-thread lifting spindle• Automatic spindle lubrication• Nylatron lifting nuts• Vertically adjustable pick-up padsfor easy accommodation• Large swing range of arms• Double-telescoped short supporting arms• Automatic unlocking and locking of arms• Accommodation of low-bed vehicles owing to 98 mmpick-up height• Spindle covers to protect supportingelements and spindleE version with electronic synchronisation(Baseframe optional)duolift BTE 3200Two-post lift without base frame and with two electricmotors• Electro-mechanical drive• Rugged columns made of specially rolled column profile• Extremely silent owing to low-maintanance Nylatronlifting nut with excellent emergency run characteristics• Elastic, low-wear and rolled-thread spindle• Lifting carriages with six rollers supportedmaintenance-free• Good access to car doors, large door stop• Chain-fracture switch• Self-locking spindle threadduolift MSE 5000Two-post lift without base frame, with 5 t rated load capacity• Lifting carriages with six large maintenance-free rollers• Rugged columns made of specially roller column profile• Automatic lubrication of lifting spindle• Smooth drive with two 3 kW electric motors• Mixed operation of cars and light trucks owing to lowpick-up height of 140 mm• Automatic arm locks for safe operation• Highest reliability owing to perfect safety nut system• Use in MB and VW garages owing to special MB and VWversions• Extremely long double-telescoped arms• Vertically adjustable pick-up pads

quattrolift + serviceliftAmple space to do the jobquattrolift 4000 S / 4000SL4-post lifts for service check-in, wheel alignment andservice work providing ample space around the vehicle• Specially suited for vehicles with low groundclearance owing to very low pick-up height• Runways adjustable to each other using a quick lock- ensuring maximum flexibility for the workplace• Absolutely torsion-free design• Cylinder fitted under runway• Level adjustment in all four columns for accuratelyhorizontal position of vehicle• Extremely short lifting time• Excellent for use as wheel alignment lift• Electro-hydraulic drive• Simple fitting without need for excavation• Simple operation owing to conspicuous control console• Electro-mechanical safety systemOptional extras• Jacking beam with 1500 kg capacity availablefor each versionservicelift 4000 SF / 5000 SFLScissor-type lift for service work,with 4 and 5 t rated load capacity respectively• Patented hydraulic system• Synchronisation via double cylinders• Accurate level checks during liftingand lowering operations• Flat structure with increased stiffness• Installation above floor level, or flush mounting possible• Including fastening means and short drive-overramps for in-ground installation

shortlift + variolioft + motoliftSpace-saving, yet efficient workplaceshortlift 2500Short-stroke lift with 2.5 t rated load capacity for tyre shopsand service check-in• Rugged and space-saving design, perfectly suitedfor harsh workshop conditions• Low drive-over height owingto new intelligent lifting system• Optional mobile kit• Large variable accommodation range of 1600 - 2100 mm• Ergonomic lifting height of 1000 mm• Workplace accessible from every side• Mechanical locking system• Including 4 rubber padsvariolift 3000-3 / 3000-3 IGvariolift 3000-3 for above floor level installationand variolift 3000-3 IG for inground installation• Extremely rugged owing to specially shapedsectional steel frame• New intelligent lifting system to ensure lowdrive-over height• Can be telescoped in bottom-most position (IG)• Automatic levelling prior to every lifting operation• No mechanical locking required because of two hydraulicsystems operating independent of each other• Workplace accessible from every side,giving access to all car doors• Extremely space-saving design• Large accommodation range (1540 bis 2100 mm)• Including 4 rubber pads• Installation-width adjustable to customer requirementsmotolift• Space-saving scissor-type lift• Universal use owing tomaximum lifting height of 1200 mm• Hinged ramps for optimum access• Independent operation owing to electro-hydraulic 220 Vdrive, hence no compressed air supply required• Divided runway to provide easy access to rear wheeland rear wheel suspension• Long drive-on ramp to facilitate driving onwith heavy motorcycles• Including mechanical front wheel clampto locate the motorcycle on the lift in three positions

multiliftThe scissor-type lift for service check-in, repairsand wheel alignmentmultilift – general information• Rated load capacity 4000 kg• Automatic levelling of runways priorto every lifting operation• Electronic control system• Synchronisation control via light barrierand follower cylinder• Clearance between runways adjustableto customer requirements• Electric and hydraulic lines guided inside the frame• Electro-hydraulic drive• Adjustable precision gear racks for optimum levelling• Installation above floor level, or flush mounting• For vehicles with a maximum wheelbase of 3600 mm• Power supply 3/PE AC 50 Hz 380-415 V• Compressed air supply 6-10 bar• GS homologation (German safety standard)• CE conformmultilift 4000 F• Runway-type lift• Width of runways 660 mm• Length of runways 4200 mm• Actual working length 3500 mm• Lifting height 1850 mm• With integrated wheel lift:• Lifting height 450 mm• Accommodation length 1350-2100 mm• Including 4 rubber pads 80 mm highmultilift 4000 AF• Runway-type lift for wheel alignment• Width of runways 660 mm• Length of runways 4200 mm• Actual working length 3500 mm• Lifting height 1850 mm• Runways with adjustable recesses for turning plates andwith integrated slip plates• Automatic adjustment of work position• With integrated wheel lift:• Lifting height 450 mm• Accommodation length 1350-2100 mm• Including 4 rubber pads 80 mm highmultilift 4000 A–MB (Mercedes approval)Runway-type lift for wheel alignmentOfficially listed by DaimlerChrysler• Runway-type lift for wheel alignment• Width of runways 660 mm• Length of runways 4200 mm• Actual working length 3500 mm• Lifting height 1850 mm• Runways with adjustable recesses for turning plates andwith integrated slip plates• Rails for jacking beam• Automatic adjustment of work position• Including holder for wheel aligner and shelves for thewheel units of the MKS system• Including wiring kit for computerised wheel alignermultilift 4000 AFLSame as multilift 4000 AF, but:• Length of runways 4800 mm• Actual working length 4100 mm• Not suitable for attachment of play detector• Rails ref. no. 1951 025 required if jacking beam is fitted

multilift1350 – 210032018504504200 (4800) 1500 /2000*max.20006602100780660* Dimension incl. stepped ramp() Dimension incl. play detectormultilift 4000 Fmultilift 4000 AF / 4000 AFL

Optional extras for automotive liftsLift type Specification Ref. no.duolift MTF 3000 Supporting baseframe to be used under unfavourable ground conditions 6490 864duolift MSE 5000 Adaptor for fork-lift truck (4 off are required) 6469 123Short supporting arms for fork-lift trucks 6490 871quattrolift 4000 S / SL Air hydraulic jacking beam with 2000 kg capacity 1950 266Extensions for pick-up pads of jacking beam 1950 267Hydro-pneumatic jacking beam with 1500 kg capacity 1951 005shortlift 2500 Mobile kit 1950 248motolift Jacking beam 1950 901servicelift 4000 SF / SFL Air hydraulic jacking beam with 2000 kg capacity 1950 266Extensions for pick-up pads of jacking beam 1950 267multilift 4000 weartest 21 ball-and-socket joint play detector with 2 directions of motion 1950 611weartest 81 ball-and-socket joint play detector with 8 directions of motion 1950 607Jacking beam 1950 209Rails for jacking beam (required for 4000 F / AF) 1950 218Rails for jacking beam (required for 4000 AFL) 1951 025Axle support for jacking beam 1950 217Kit for quick lifting and lowering (approx. 25 s) 1950 613Lighting system with protections 1950 208Supporting baseframe for duolifts

Accessories for automotive liftsLift type/series Specification Ref. no.duolift 2500/3200/5000 Pick-up pads, vertically adjustable 6464 307duolift 3000 Pick-up pads, vertically adjustable 6490 900Large door stop 6490 886duolift 2500/3000/3200 Accessory kit for vans and light trucks 6464 297duolift 2500/3000/ Pick-up pads, stationary 6463 8523200/5000 Adaptor for pick-up pads for MB jeep 6490 373Replacement kit (plastic pad adaptors) for MB jeep pads 1701 363Bucklestraps for MB jeep and MB-100 van adaptors 6490 091Pick-up pads, vertically adjustable, for MB jeep and MB-100 6464 299Safety plug-in adaptors for MB cars 6490 301Safety means for MB A class 1951 510duolift 2500/3000/ Utilities station to be attached to secondary post 6490 1293200/5000/monolift Add-on pads 6462 859Add-on pads for Porsche cars with A/C 6490 217duolift 5000 Accessory kit for MB Sprinter and VW LT2 6490 808Accessory kit for vans and light trucks 6490 860Add-on pad for MB-100 van 6490 514Hour counter 6490 823Wheel grips for lifting by the wheels 6490 853Supporting frame for use under unfavourable ground conditions 6490 829shortlift Rubber pads, 40 mm high 1950 258Rubber pads, 80 mm high 1950 261variolift Rubber pads, 40 mm high 1950 258Drive-on ramps, 1100 mm long 1950 255Hose extensions 1950 615servicelift Drive-on ramps 1950 264Hose extension set 1950 265multilift Stepped drive-on ramps 1950 204Drive-on ramps 1950 203Dummy plates for turning plate recesses (AF, AFL), 2 off 1950 620Dummy plates for turning plate recesses (AF, AFL) 8 off 1950 614Hose extension set (S, SL) 1950 615Hose extension set (F) 1950 617Hose extension set (AF, AFL) 1950 618Hose extension set for play detector 1950 619Rubber pads, 40 mm high 1950 258Rubber pads, 80 mm high 1950 261quattrolift Drive-off ramps (S) 1951 514Drive-off ramps (SL) 1951 515

Technical dataTechnical data and dimensionsSeries monolift duolift quattroliftType ME 2.0 GTE 2500 BT 2500 MTF 3000/E BTE 3200 MSE 5000 4000 S 4000 SLLifting height A mm 1890 1965 1965 2030 1925 2040 1800 1800Overall width C mm 1730 3260 3010 3200 3250 3660 3160 3310Rated load capacity kg 2000 2500 2500 3000 3200 5000 4000 4000Lifting time ca. s 45 45 45 45 45 40 30 30Motor rating kW 3 3 3 2 x 1.8 2 x 2 2 x 3 3 3Weight approx. kg 700 680 700 630 700 1000 920 1000Lifting travel mm 1780 1800 1800 1890 1800 1820 1665 1645Pick-up height B mm 110-170 105 – 165 105 – 165 98 – 140 125 140 – 220Width between columns D mm 2750 2500 2560 2740 3000 2700 2850Track width E mm 2560 2310 2250 2510 2780Vertical clearance mm 3850 3200/4200 4200 4200/5000Overall height F mm 2840 2580 3920 4230 4260 5035 2330 2330Telescoped supporting arms front single single double double single doubleTelescoped supporting arms rear single single single single single doubleFront arm length(ME right-hand) mm 640–1010 600–1050 408–840 460–880 620–1046 850–1900Rear arm length (ME left-hand) mm 580–950 835–1285 840–1360 950–1580 788–1380 850–1900Admissible load distribution 2:3 2:3 / 3:2 2:3 / 3:2 2:3 2:1 / 1:2 1:2 2:1 2:1Arm synchronisation Chain Chain Cable 1 Chain CableLength of runways/pad plates* mm 4300 4800Actual working length mm 3600 4100Width of runways/pad plates* mm 540 540Drive-on height mm 135 155Length of drive-on ramps mm 1200 1200Length of stepped drive-on ramps mmOverall length incl. drive-on ramps mm 5640 6140Overall length incl. stepped drive-on rampsmmWidth between runways mm 710–1160 900–1190Accommodation rangemmPower supply3/N/PE AC 50 Hz 380–415 V 3/PE AC 50 Hz 380–415 V Wheel liftMax. accommodation lengthMin. accommodation lengthLifting heigthRated load capacitymmmmmmkg1E versionwith electronicsynchronisation

shortlift variolift motolift servicelift multilift2500 3000-3/IG 4000 SF 5000 SLF 4000 F 4000 AF 4000 AFL 4000A-MB1000 1850/1725 1200 1950 1950 1850 1850 1850 18501790 1950 695 2080 2080 2100 2100 2100 21002500 3000 500 4000 5000 4000 4000 4000 400015 45 10 45 45 40 40 40 403 3 3 3 3 3 3 3 3500 600 195 1300 1400 2200 2400 2400 2400910 1730/1725 1050 1810 1790 1530 1530 1530 15303:2 3:2 3:2 2:1 2:1 2:1 2:1 2:1 2:12100* 2100* 2275 4200 4800 4200 4200 4800 42003500 4100 3500 3500 4100 3500500* 600* 695 625 625 660 660 660 66090 120/00 150 140 160 320 320 320 320315 350/00 500 500 500 1500 1500 1500 15002000 2000 2000 20002230 2240 2775 4700 5300 5700 5700 6300 57006200 6200 6800 6200790 750 830 830 780 780 780 7801600–2100 1540–2100 2100 2100 21001350 1350 1350450 450 4504000 4000 4000

Innovation is our businessThe complete range of automotive service equipment and servicesTrainingInstallationSpare partsRepairsWheel balancers Tyre changers ServiceTest lanes Wheel aligners TrainingYour Hofmann dealer9402 561 08.03 Printed in GermanyQuality counts• Certified toISO 9001:2000Snap-on Equipment GmbH • Geschäftsbereich Hofmann Werkstatt-Technik • PF 1202 • D-64311 Pfungstadt +49 61 57 12-450 • Fax +49 61 57 12-229 • www.hofmann-ge.com • sales@hofmann-ge.comTechnical alterations reserved.