Repair Parts Diagram - American Standard

COLONY 5’ X 30” w/INTEGRAL APRONWHIRLPOOL AND BATHING POOLHIGH GLOSS ACRYLICCOLONY 5’ x 30” WHIRLPOOL AND BATHINGPOOL with INTEGRAL APRON❏ 2740.118 Whirlpool, Right Hand Outlet❏ 2740.218 Whirlpool, Left Hand OutletProduct Features:• High Gloss Acrylic with fiberglassreinforcement• Integral apron with removable access panel• Integral three-sided, tiling/water retentionflange• Integral lumbar support• Molded-in arm rests with elbow supports• Safety textured tub bottom patternFactory installed and tested whirlpool systemfeaturing:• Rigid P.V.C. piping• 1 H.P. self-draining pump/motor with Dry Runseal• Six multi-direction jets• One air volume control• Anti-vortex suction fitting• Deck mounted air switch On/Off control• U.L.® Listed entire whirlpool system❏ 2740.102 Bath only, Right Hand Outlet❏ 2740.202 Bath only, Left Hand Outlet• Same as above without whirlpool systemTo Be Specified - :❏ Color:❏ Bath/Shower Faucet*:❏ Faucet Finish:❏ Bath Drain: 1553.270❏ 002 Chrome ❏ 099 Polished Brass* See faucet section for models availableNominal Dimensions:(59-7/8” x 29-7/8” x 19-1/4")1521 x 759 x 489mmCompliance Certifications -Meets or Exceeds the Following Specifications:• Underwriters Laboratories - HydromassageBathtubs UL 1795• ASME A112.19.7M for Whirlpool Appliances• ANSI Z124.1 for Plastic Bathtubs• ASTM E162 for Flammability• NFPA 258 for Smoke DensityNOTE: Roughing-in dimensions and product specificationsshown on reverse side of page.12/99SPS 2740© 1999 American Standard Inc.BV-018B

COLONY 5’ X 30” w/INTEGRAL APRONWHIRLPOOL AND BATHING POOLHIGH GLOSS ACRYLIC6-1/4(159mm)C/L OF DRAIN3/4(19mm)FINISHEDWALLSEE FITTINGSPECS FORDIMENSIONS1-1/2 O.D.TAILPIECE59-7/8(1521mm)WATERRETENTIONFLANGE(3 SIDES)14-1/8(359mm)6-1/4(159mm)C/L OF DRAIN3/4(19mm)FINISHEDWALLSEE FITTINGSPECS FORDIMENSIONS1-1/2 O.D.TAILPIECE59-7/8(1521mm)WATERRETENTIONFLANGE(3 SIDES)14-1/8(359mm)29-7/8(759mm)C/L OFSUPPLIESPUMPON/OFFSWITCH29-7/8(759mm)C/L OFSUPPLIESHORIZONTAL TAILPIECEABOVE FLOOR OUTLET1-1/2 (38mm)OPTIONAL TOFINISHED FLOORUSUALLY BETWEEN65 & 78(1651 & 1981mm)7/8 WATERRETENTIONFLANGE(3 SIDES)C/L OFOVERFLOW3(76mm)ACCESS TO PUMP/MOTOR(1) AIR VALVETHROUGH REMOVABLE(6) JETSFRONT ACCESS PANELC/L OFSHOWER ARM12(305mm)OPT.4(102mm)FINISHEDWALLC/L OFVALVESC/L OFSPOUT■ LEVELING STRINGERNOT FOR SUPPORTHORIZONTAL TAILPIECEABOVE FLOOR OUTLET1-1/2 (38mm)OPTIONAL TOFINISHED FLOORUSUALLY BETWEEN65 & 78(1651 & 1981mm)7/8 WATERRETENTIONFLANGE(3 SIDES)C/L OFOVERFLOW3(76mm)12(305mm)OPT.4(102mm)C/L OFSHOWER ARMFINISHEDWALLC/L OFVALVESC/L OFSPOUT■ LEVELING STRINGERNOT FOR SUPPORTTOP OFDECK19-1/4(489mm)19(483mm)UNDERSIDEOF DECKTOP OFDECK19-1/4(489mm)19(483mm)UNDERSIDEOF DECKROUGHFLOORROUGHFLOOR3-3/4(95mm)2-1/2(64mm)3-3/4(95mm)2-1/2(64mm)BATH SUPPORTMATERIALBATH SUPPORTMATERIALGENERAL SPECIFICATIONS FOR 2740 WHIRLPOOLINSTALLED SIZEWEIGHTWEIGHT w/WATERGAL. TO OVERFLOWWHIRLPOOL MIN. OPERATING VOL.BATHING WELL AT SUMPBATHING WELL AT RIMWATER DEPTH TO OVERFLOWFLOOR LOADING(PROJECTED AREA)PTS.CUBE (FT 3 )59-7/8 x 29-7/8 x 19-1/4 (1521 x 759 x 489mm)105 Lbs. (47 Kgs.)480 Lbs. (216 Kgs.)45 Gal. (171 L)38 Gal. (144 L)20 x 46 (508 x 1168mm )25-1/2 x 55-1/2(648 x 1410mm )11-1/2 (292mm)39 Lbs./Sq.Ft. (188 Kgs./Sq.m)16.733.0WHIRLPOOL ELECTRICAL SPECIFICATIONSSYSTEM I PUMP1 HP, 9.9 AMPS,120V.GENERAL SPECIFICATIONS FOR 2740 BATHING POOLINSTALLED SIZEWEIGHTWEIGHT w/WATERGAL. TO OVERFLOWBATHING WELL AT SUMPBATHING WELL AT RIMWATER DEPTH TO OVERFLOWFLOOR LOADING(PROJECTED AREA)PTS.CUBE (FT 3 )59-7/8 x 30 x 19-1/4 (1521 x 762 x 489mm)70 Lbs. (32 Kgs.)462 Lbs. (208 Kgs.)47 Gal. (178 L)20 x 46 (508 x 1168mm )25-1/2 x 55-1/2(648 x 1410mm )11-1/2 (292mm)37 Lbs./Sq.Ft. (179 Kgs./Sq.m)16.733.0NOTES:BATH TO BE INSTALLED ABOVE FLOOR LINE AS A RECESS INSTALLATION.■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.BATH TO BE INSTALLED ABOVE FLOOR LINE AS A RECESS INSTALLATION.LEFT HAND OUTLET SHOWN, RIGHT HAND REVERSE DIMENSIONS (2740.118).FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established byANSI Standards Z124.1 and A112.19.7. These measurements are subject to change or cancellation. Noresponsibility is assumed for use of superseded or voided pages.© 1999 American Standard Inc.