stripall 6pgr.qxd - Stanley Supply & Services

More documents

Recommendations

Info

quick, clean & easy1Position the wire between the bladesand against the stop2Depress the heat buttonand close the electrodesEasy to useAfter adjusting the stripand gauge stops, insert a wirebetween the blades and pressthe heat button. When the bladessever the insulation, rotate ¼ turn asyou continue to apply heat. Releasethe heat button, and pull off thecompletely severed insulation.34Rotate ¼ turnand releasePull off theinsulationA style for all your needsElectrodeStyleStandard(110 volt)Standardw/TempControlHV(220 volt)OptionsESDStd. Length1.5”TW-1TWC-1TW-1HVTWC-1HVTWC-1ESDLong-nose3.5”TW-2TWC-2TW-2HVTWC-2HVTWC-2ESDCoaxial(slitter)TW-6TWC-6TW-6HVTWC-6HVTWC-6ESDHigh Voltage OptionAll STRIPALL® products are also available in 220 volt AC,50 Hz. configurations (denoted with a HV suffix).
accessoriesTC-1The optional control unit adjustsblade temperature from1700°F to 100°F to reduceblade temperature forinsulation materials that burn,scorch or emit fumes. TW-*units can be converted toTWC-* as needed.Table Bench Mount (TBM)This optional bench stand is designedfor holding the STRIPALL® in a fixedwork position.r Reduces operator fatiguer Stripper can be easily removed fromthe stand when hand-held operationis desiredr Works with all STRIPALL® modelsBlade optionsTo insure the best performancepossible, two types of bladesare available. The notchedblades perform best on wires10 – 25 AWG. The blank bladesare designed for stripping wires26 – 38 AWG.Replacement partsitem # part # description1 001-300-1 case - left2 001-300-2 case - right3 001-100-1 transformer001-100-2 transformer - high voltage (220V)4 001-101-1 handle assy - short nose for TW-1 & TWC-1001-101-2 handle assy - long nose for TW-2 & TWC-24A 001-101-3 handle assy - TW-6 & TWC-65 001-104-1 nose block assy - short nose for TW-1 & TWC-1001-104-2 nose block assy - long nose for TW-2 & TWC-25A 001-104-3 nose block assy for TW-6 & TWC-65B 001-101-5 knurled screw, 6-32 x 1” for TW-6 & TWC-66 001-107-1 power cord - three prong7 001-317-1 spring - handle8 001-316-3 gauge stop9 001-316-4 strip stop10 001-312-1 blade-blank, screws incl., TW/TWC-1 & TW/TWC-2001-312-2 blade-notched, screws incl., TW/TWC-1 & TW/TWC-210A 001-312-5 blade for TW-6 & TWC-611 #6-32NC x 1” screw, pan head, steel, zinc plated12 #6-32NC x 7/8” screw, pan head, steel, zinc plated13 #6-32NC nut - hex, steel, zinc platedTBM table bench mount (not shown in figure 1)TC-1 temperature control (not shown in figure 1)14 001-303-1 heat button assembly15 803305-1 switch assembly16 001-330-1 power cord (220V)17 TC-1HV temperature controller (220V)fig. 1
Page 1 and 2: STRIPALL ®by TELEDYNEHandheld Ther
Page 3: featuresr Thermal wire stripping to

stripall 6pgr.qxd - Stanley Supply & Services

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?