B UTTERFLY V ALVES - valves.com.ua

More documents

Recommendations

Info

FEATURESBray Controls is proud to offer a high quality line offlanged butterfly valves to meet the requirements oftoday’s market. Combining years of field applicationexperience, research and development, Bray hasdesigned many unique features in the Series 3A/3AHnot previously available. The results are longer servicelife, greater reliability, ease of parts replacement andinterchangeability of components.Bray’s Series 3A/3AH valves are a double flangeddesign which can be used for dead-end service. AllBray valves are tested to 110% of full pressure ratingbefore shipment.A major design advantage of Bray valve product lines isinternational compatibility. The same valve is compatiblewith most world flange standards – ASME Class 125/150,BS 10 Tables D and E, BS 4504 NP 10/16, DIN ND 10/16,AS 2129 and JIS10. In addition, the valves are designed to complywith ISO 5752 - Table 2 (short pattern) face-to-face and ISO 5211actuator mounting flanges. Therefore, one valve design can beused in many different world markets.Bray interchangeability and compatibility offers the bestin uniformity of product line and low-cost performancein the industry today.DISCSpherically machined and hand polished to provide a bubbletightshut off, minimum torque, and longer seat life. Standardmaterial is Nylon 11 coated ductile Iron. Other materialsavailable on request.Stem RetainingAssemblyActuatorMountingFlange/StemConnectionExtendedNeckPRIMARY AND SECONDARY SEALSThe primary seal is achieved by pre-loaded contactof spherically machined hand polished disc hubswith unique molded seat flat surfaces. This sealingmethod isolates the flowing media from the stemand body material at all angles of valve disc seating.A secondary seal is achieved by an interferencefit of the stem and seat hole diameters.STEM RETAINING ASSEMBLYThe stem is retained in the body by means of a uniqueStainless Steel “Spirolox ® ” retaining ring, a thrust washerand two C-rings, manufactured from brass as standard,stainless steel upon request. The retaining ring may be easilyremoved with a standard hand tool. The stem retaining assemblyprevents unintentional removal of the stem during field service.DiscFlangedBodyDisc & StemConnectionSeatStem Retaining AssemblyStem BushingStem SealNylon 11 CoatingA thermoplastic coating produced from a vegetable base andis USDA Approved, as well as, certified to ASME/NSF61for water service. It is inert to fungus growth and mold,has excellent resistance to impact and provides a very lowcoefficient of friction.STEM BUSHING Non-corrosive, heavy duty acetal bushingabsorbs actuator side thrusts.STEM SEAL Double “U” cup seal design is self-adjusting,gives positive sealing in both directions, and prevents externalsubstances from entering the stem bore.EXTENDED NECK Extended neck length allows for 2" of pipinginsulation and is easily accessible for mounting actuators.Nylon 11 also has superior corrosion resistance and has beenused successfully in many applications such as water, cement,food and seawater. Bray's Nylon 11 coating has been salt spraytested in excess of 2000 hours and used in seawater immersionservice for over 25 years without any deterioration of the coatingresulting in no corrosion to the coated metal components. Asa result, the use of Nylon 11 in seawater with elevated chloridelevels between 30,000 - 40,000 ppm continues to increase.“Spirolox ® ” designation is a registered trademark of Kaydon Ring and Seal, Inc.2
selection dataFLANGE REQUIREMENTSBray valves are designed for installation between ASME Class125/150 lb. weld-neck or slip-on flanges, BS 10 Tables D &E, BS 4504 NP 10/16, DIN ND 10/16, AS 2129 and JIS 10,either flat faced or raised faced. While weld-neck flanges arerecommended, Bray has specifically designed its valvePRESSURE RATINGSFor Bi-directional Bubble-Tight Shut-Off and Dead-End ApplicationsSERIES 3ASize Range Standard Disc Reduced Disc*2"-12" (50-300 mm) 175 psig (12.1 bar) 50 psig (3.5 bar)14"-20" (350-500 mm) 150 psig (10.3 bar) 50 psig (3.5 bar)SERIES 3AH2"-20" (50-500 mm) 250 psig (17.2 bar) NA NA*For low pressure application, Bray offers a standard reduced disc diameter to decrease seating torques and to extendseat life, thus increasing the valve’s performance and reducing actuator costs for the customer consult factory.VELOCITY LIMITS FOR ON-OFF SERVICEFluids – 30 ft/sec (9 m/s)Gases – 175 ft/sec (54 m/s)seat to work with slip-on flanges, thus eliminating commonfailures of other butterfly valve designs. When using raisedface flanges be sure to properly align valve and flange. TypeC stub-end flanges are not recommended.øFøGBolt CircleFlangeDIMENSIONS SERIES 3A/3AH - ins (mm)Valve Sizeins(mm)A B C D* E FTop Plate DrillingBoltCircleNo.HolesHoleDia.G H J K LFlange Bolting DataBoltCircleNo.HolesThreadsUNC-2B45°2(50)6.50(165)4.25(108)2.00(51)2.84(72)5.50(140)3.54(90)2.76(70)4.39(9.9).55(14).39(10)1.25(32)X.79(20)4.75(121)4 5/8-112.5(65)7.28(185)4.41(112)2.50(64)3.34(85)6.00(152)3.54(90)2.76(70)4.39(9.9).55(14).39(10)1.25(32)X.79(20)5.50(140)4 5/8-113(80)7.87(200)4.49(114)3.00(76)4.03(102)6.25(159)3.54(90)2.76(70)4.39(9.9).55(14).39(10)1.25(32)X.87(22)6.00(152)4 5/8-114(100)8.66(220)5.00(127)4.00(102)5.16(131)7.00(178)3.54(90)2.76(70)4.39(9.9).63(16).43(11)1.25(32)X.95(24)7.50(191)8 5/8-115(125)9.84(250)5.51(140)5.00(127)6.16(156)7.50(190)3.54(90)2.76(70)4.39(9.9).75(19).51(13)1.25(32)X1.03(26)8.50(216)8 3/4-106(150)8(200)11.22(285)13.50(343)5.51(140)5.98(152)5.75(146)7.75(197)7.02(178)9.47(241)8.00(203)9.50(241)3.54(90)5.91(150)2.76(70)4.92(125)44.39(9.9).57(14.5).75(19).87(22).51(13).63(16)1.25(32)1.25(32)1.78(45)5.00(127)1.03(26)1.18(30)9.50(241)11.75(298)8 3/4-108 3/4-10(Across Flats)HJ10(250)15.94(405)6.50(165)9.75(248)11.47(291)10.75(273)5.91(150)4.92(125)4.57(14.5)1.18(30).87(22)2.00(51)7.35(187)1.26(32)14.25(362)12 7/8-912(300)19.00(483)7.01(178) 11.75(298)13.47(342)12.25(311)5.91(150)4.92(125)4.57(14.5)1.18(30).87(22)2.00(51)9.53(242)1.26(32)17.00(432)12 7/8-9EValve SizeA B C D* E FTop Plate Drillingins(mm)14(350)21.00(533)7.48(190) 13.25(337)15.28(388)13.62(346)5.91(150)BoltCircle4.92(125)No.Holes4HoleDia..57(14)G1.38(35)KeySize J K L.39x.39(10x10)2.00(51)11.07(281)1.42(36)Flange Bolting DataBoltCircle18.75(476)No.HolesThreadsUNC-2B12 1-8KCD16(400)23.50(597)8.51(216) 15.25(387)17.41(442)14.75(375)5.91(150)4.92(125)4.57(14)1.38(35).39x.39(10x10)2.00(51)12.81(325)1.50(38)21.25(540)16 1-818(450)25.20(640)8.74(222) 17.25(438)19.47(495)16.00(406)8.27(210)6.50(165)4.81(21)1.97(50).47x.39(12x10)2.50(64)15.02(381)1.65(42)22.75(578)16 11/8-720(500)28.15(715)9.02(229) 19.25(489)21.59(548)17.25(438)8.27(210)6.50(165)4.81(21)1.97(50).47x.39(12x10)Note: K dim is disc chordal dimension at valve face* Flat Faced Flange Available - Contact factory for dimensional information2.50(64)17.15(436)1.65(42)25.00(635)20 11/8-7BL3
Page 1: utterfly valvesresilient seated®se
Page 5 and 6: BODYOne-piece double flanged body.

B UTTERFLY V ALVES - valves.com.ua

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?