Rig Fleet (PDF) - Maersk Drilling

Jack-Up Rig DataMAERSKRESOLVE(RSV)ABSMAERSKRESOLUTE(RSU)ABSMAERSKRESILIENT(RSI)ABSMAERSKREACHER(REA)ABSMAERSKCOMPLETER(CPL)ABSMAERSKCONVINCER(CVI)Design MSC CJ50-100 MC Baker Pacific Class 375ABSMÆRSKGALLANT(GAL)LloydsMSCCJ62-120SMÆRSKGIANT(GIA)DNVMAERSKGUARDIAN(GUA)LloydsMÆRSKINNOVATOR(INN)DNVMÆRSKINSPIRER(INS)DNVMAERSKENDURER(EDU)ABSHitachi - Giant Class MSC CJ70-150 MC BMC 350Hull A Length of hull m 70,0 72,1 78,2 84,0 88,8 72,0B Width of hull m 68,0 68,4 90,3 90,0 102,5 72,0C cHeight from bottom of hull to bottom of cantilever m 10,60 9,45 11,66 10,27 13,10 9,99At centre line9,80 8,53 11,20 9,90 12,0 9,44C hHeight of hull:mAt hull side 9,50 8,53 10,79 9,50 11,5 9,14D Transverse leg spacing (Starboard to Port) m 50,0 47,3 62,0 66,0 70,0 50,0E Longitudinal leg spacing (Bow to Aft) m 43,30 44,30 53,73 56,80 60,68 49,75F Distance from transom to centre of aft spudcan m 16,50 14,40 10,77 13,50 13,30 10,85Distance from transom to sternest point m 1,43 1,20 1,60 1,60 1,80 2,10LegH Leg -length:To tip of spudcan146,30 154,23 175,30 156,80 203,35 146,06mTo bottom of skirt / chord N/A N/A N/A 160,15 N/A 204,30 N/AHeigth of jacking unit support structure above maindeck (Measurement based on fwd jacking structure)m 10,78 12,09 13,80 14,40 13,78 13,43J Max. available leg-length below hull (H*- I - C h*-1,5) m 124,22 132,11 148,80 131,00 176,07 121,69Max. water depth (Original Design)106,70 114,30 120,00 106,70 150,00 106,68Km@ Penetration 5,00 3,05 5,00 W/O skirts:5,0 5,00 3,00 4,57L Max. airgap m 40,00 25,00 40,00 25,50 24,20 30.5 (** 43.5 ) 30,50 45,00 30,50Draught Maximum load line draught m 5,75 5.75, (*: 11.95) 5,94 6,65 4.8, (* 8.15) 4,80 8,00 5,21Spud Can M Max fwd-aft distance of spudcan m 15,93 21,08 16,95 19,50 20,09 22,00 18,00Projected area of spudcan m 2 200,0 349,00 228,3 250,0 252,8 380,0 226,0Shape of spudcan - Hexagon Circular Dodecagon (12) Hexagon Hexagon Clover Skew cloverN Distance from edge of spud can to transom m 7,70 6,00 5,93 1,02 3,45 2,30 1,85Drilling Envelope P Min. longitudinal reach of rotary from transom m 3,05 pending 3,05 3,05 3,10 2,00R Max. longitudinal reach of rotary from transom m 21,34 21,34 19,27 16,76 21,34 27,43 30,48 16,76S Max. transverse reach of rotary from centreline m 7.2S TB / 6.8 PS 4,57 4,6 4 (***3.08) 4,6 9.6 STB / 10.5 PS 4,9Drill-Floor T Max. longitudinal reach from transom m 26,66 28,27 26,20 23,01 33,73 36,78 23,44V Max. width incl. skidding from centreline, Starboard m 18,56 17,85 14,90 15.07 (***14.15) 21,10 17,98X Max. width incl. skidding from centreline, Port Side m 17,68 14,05 15,63 16.2 (***15.28) 21,00 17,67Cantilever Y Height of drillfloor over main deck m 13,50 14,35 11,67 11,17 14,82 11,91Z Overall width of cantilever excl. platforms etc. m 14,60 18,86 20,09 17,60 16,00 17,68Note: *: Draught to skirt tip **: Within reach if modified. ***: Current configuration of the rigI