Gardner-Denver Aire Hoist Catalog - Tecno Italia s.r.l

General AccessoriesFilters, Regulators, Lubricators■ Modular ConstructionFilter Regulator LubricatorsModel NumberNPTDimensionsSize Air Flow Bowl CapacityA B CIn. SCFM m3/min. oz. liter in. mm in. mm in. mmFiltersF02-M 1/4 35 9.9 5.0 0.15 5.6 142 3.0 76 0.9 23F03-M 3/8 44 12.9 5.0 0.15 5.6 142 3.0 76 0.9 23F04-M 1/2 138 39.1 10 0.30 6.4 163 3.4 86 1.0 25Lubricators – Economist (Standard Mist)L02-EP 1/4 28 3.7 5.0 0.15 4.8 122 3.0 76 1.6 41L03-EP 3/8 48 6.2 5.0 0.15 4.8 122 3.0 76 1.6 41L04-EP 1/2 102 13.6 10 0.30 5.4 137 3.4 86 1.6 41Lubricators – Atomist (Fine Mist)L02-AP 1/4 28 3.7 5.0 0.15 4.8 122 3.0 76 1.6 41L03-AP 3/8 48 6.2 5.0 0.15 4.8 122 3.0 76 1.6 41LO3-AP 1/2 102 13.6 10 0.30 5.4 137 3.4 86 1.6 41Model NumberNPTPressure RangeDimensionsSize Air Flow (maximum)A B CIn. SCFM m3/min. psig bar in. mm in. mm in. mmRegulatorsRO2-G 1/4 80 10.8 125 8.5 3.9 99 3.0 76 1.3 33RO3-G 3/8 80 10.8 125 8.5 3.9 99 3.0 76 1.3 33R04-G 1/2 195 26.1 125 8.5 5.6 142 3.4 86 1.4 36Modular Sleeve (with O-Ring)Model: MS101Unique modular sleeve design easily and quicklyconnects one or more units and accessories togetherwithout pipe nipples. hand tightening the threaded pinprovides a tight seal between the units. Modularsleeves do not add length to combination assemblies,and make a more compact installation.Modular Sleeve & Bracket (with O-Ring)Model: MS101Combination sleeve/wall mounting bracket as shown.Designed for mounting a single unit or combination ofunits directly to the wall. The sleeve and mountingbracket can be ordered assembled from the factory,or just the mounting bracket alone to be used onexisting modular sleeves.Modular End Blocks (sold in pairs)Model: 1/4" NPTF – EB-1023/8" NPTF – EB-1031/2" NPTF – EB-1043/4" NPTF – EB-106The threaded End Blocks, together with the modular sleeves,allows a single unit or a combination of units to be piped intothe air system in the modular mode. This feature allows easeof unit servicing or replacement without disturbing the airlineconnections. End blocks add 1.19" (30mm) to each end ofthe unit where used.NOTE: The 3/4" end blocks are designed only to adapt to 3/4" piping systems and do notincrease flow ratings listed for any unit.Automatic DrainModel: AD-101Automatic Mechanical Drain is a float-typemechanism with a 1/8" NPT threaded drain portcompletely enclosed in the filter bowl. The float isconstructed of rigid cellular rubber. The drain willoperate automatically under air pressure rangingfrom 20 to 175 psig (1.5 to 12 bar).56