Installation & Instruction Manual - Reverse Osmosis, RO Water ...

More documents

Recommendations

Info

22. Storage tank3. Faucet with mounting hardware4. Installation packet containing: drain saddle, tank ball valve, two mounting screws, and otherinstallation pieces depending on system.OPERATION PARAMETERS:WARNING!! The following conditions for feed water supply must be met or warranty will be void.1. System must be connected to a municipal or well water source that is treated and tested on a regularbasis to insure water is microbiologically safe.2. Operating outside temperatures:Maximum 90 °FMinimum 40 °FCAUTION!! Do not allow system to freeze. The membrane always contains water and will bedestroyed if frozen.WARNING!! Do not plumb system to hot water. This will destroy the membrane and void thewarranty and manufacturer’s responsibility.3. Operating pressure:Maximum 80 PSIMinimum 40 PSIThis reverse osmosis system is designed to operate at a water pressure in the range of 40 to 80 PSI.At pressures lower than this, the quantity as well as quality will be reduced. At higher pressure,severe, damage to the system may result. A pressure regulator must be installed on the feedwater source, which reduces the water pressure coming into the system.WARNING!! Warranty voided and manufacturer assumes no responsibility for damage to system orproperty if pressure exceeds 80 PSI.4. Turbidity:
31Preparing For InstallationPreparing for installation1. This system includes a standard sinktop faucet without an air-gap. Inlocalities where plumbing codes requireinstallation of an air-gap, contact yourlocal distributor to obtain a codeapproved drain line adapter.2. The reverse osmosis system may bemounted to the side of the sink cabinetor set on the floor of the sink cabinet. Itmust be positioned to allow access forservice and filter changes. Theassembly should be relatively near thefaucet to maximize flow rate. Seediagram A for a positioning example.3. The storage tank should be locatedwhere it can be removed if necessary.The storage tank may be placed ineither the vertical or horizontal positionwithout affecting the systemperformance. If there is insufficientspace under the sink for placement, thetank may be located in an adjacentcupboard up to 50 ft. away. Seediagram A for a positioning example4. The faucet should be positioned to allowa free flow pattern into the sink. It mustbe positioned to allow ready access tothe mounting hardware under the sink.See diagram A for a positioningexampleDiagram A2Faucet InstallationCAUTION!! Extreme care must betaken in drilling the hole for the sink-topfaucet. The surface material of mostsinks is extremely hard and brittle andcan be easily chipped or cracked. If youare uncomfortable performing thefollowing procedure it is recommendedthat your local distributor be consultedfor techniques and other assistance.The system’s manufacturer accepts noresponsibility for sink top damageresulting from system installation.CAUTION!! Before grinding or drillingput on appropriate eye protection(i.e.…goggles) to protect yourself fromporcelain or metal chips.CAUTION!! Before grinding or drillingensure that the drill you are using isUL® Laboratories approved andproperly grounded to prevent electricalshock. DO NOT USE DRILL WHILEUSING OR STANDING IN WATER!!1. BEFORE DRILLING: Check under thesink in the area that you plan to installthe faucet and make sure that there is aflat surface to secure the mountinghardware. A flat space of approximately2 inches in diameter is needed.SAMF-108 Rev. B 06/16/093
Page 1: 1Installation & Instruction ManualR
Page 5 and 6: 5Faucet DiagramUP FORCONSTANTFULL F
Page 8 and 9: 8IMPORTANT!! Be very careful not to
Page 10 and 11: 1012TROUBLESHOOTINGNot Enough Water
Page 12: 12WARRANTY CERTIFICATEREVERSE OSMOS

Installation & Instruction Manual - Reverse Osmosis, RO Water ...

Create successful ePaper yourself

Delete template?

Save as template?