Material Safety Data Sheet - Movac Group Limited

More documents

Recommendations

Info

DRSafety Data Sheetaccording to 1907/2006/EC, Article 31Page 2/6Printing date 22.05.2008 Revision: 06.04.2008Trade name: 14 Line Polyurethane (contains lead)· Additional information: For the wording of the listed risk phrases refer to section 16.(Contd. of page 1)4 First-aid measures· General information:Symptoms of poisoning may even occur after several hours; therefore medical observation for at least 48hours after the accident.· After inhalation: Supply fresh air; consult doctor in case of complaints.· After skin contact: Generally the product does not irritate the skin.· After eye contact: Rinse opened eye for several minutes under running water.· After swallowing: Call for a doctor immediately.5 Fire-fighting measures· Suitable extinguishing agents:CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.· For safety reasons unsuitable extinguishing agents: Water with full jet· Protective equipment: Put on breathing apparatus6 Accidental release measures· Person-related safety precautions: Wear protective equipment. Keep unprotected persons away.· Measures for environmental protection:Inform respective authorities in case of seepage into water course or sewage system.Do not allow to enter sewers/ surface or ground water.· Measures for cleaning/collecting:Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).Dispose contaminated material as waste according to item 13.Ensure adequate ventilation.7 Handling and storage· Handling:· Information for safe handling:Keep receptacles tightly sealed.Ensure good ventilation/extraction at the workplace.Open and handle receptacle with care.Prevent formation of aerosols.· Information about fire - and explosion protection:Keep ignition sources away - Do not smoke.Protect against electrostatic charges.Keep respiratory protective device available.· Storage:· Requirements to be met by storerooms and receptacles: No special requirements.· Information about storage in one common storage facility: Not required.· Further information about storage conditions: Keep receptacle tightly sealed.8 Exposure controls/personal protection· Additional information about design of technical facilities: No further data; see item 7.(Contd. on page 3)GB
DRSafety Data Sheetaccording to 1907/2006/EC, Article 31Page 3/6Printing date 22.05.2008 Revision: 06.04.2008Trade name: 14 Line Polyurethane (contains lead)· Ingredients with limit values that require monitoring at the workplace:7758-97-6 lead chromateWEL Long-term value: 0.5 mg/m³as Cr1330-20-7 Xylene (mix)WEL Short-term value: 441 mg/m³, 100 ppmLong-term value: 220 mg/m³, 50 ppmSk; BMGV· Additional information: The lists valid during the making were used as basis.(Contd. of page 2)· Personal protective equipment:· General protective and hygienic measures:Keep away from foodstuffs, beverages and feed.Immediately remove all soiled and contaminated clothingWash hands before breaks and at the end of work.Store protective clothing separately.· Respiratory protection:In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposureuse respiratory protective device that is independent of circulating air.· Protection of hands:When skin exposure may occur, advice should be sought from the glove supplier on appropriate types andusage times for this product.Protective gloves`SThe glove material has to be impermeable and resistant to the product/ the substance/ the preparation.Selection of the glove material on consideration of the penetration times, rates of diffusion and thedegradation· Material of glovesThe selection of the suitable gloves does not only depend on the material, but also on further marks of qualityand varies from manufacturer to manufacturer. As the product is a preparation of several substances, theresistance of the glove material can not be calculated in advance and has therefore to be checked prior to theapplication.· Penetration time of glove materialThe exact break through time has to be found out by the manufacturer of the protective gloves and has to beobserved.· Eye protection:Tightly sealed goggles`R9 Physical and chemical properties· General InformationForm:Colour:Odour:· Change in conditionMelting point/Melting range: Undetermined.Boiling point/Boiling range: 137°C· Flash point: 38°CFluidAccording to product specificationCharacteristic(Contd. on page 4)GB
Page 1: DRSafety Data Sheetaccording to 190
Page 5 and 6: DRSafety Data Sheetaccording to 190

Material Safety Data Sheet - Movac Group Limited

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?