Download trade drawing - Southco

654321REVISION HISTORYREV DATEBYDESCRIPTIONE 04APR2014 CMS/BGL PRN: P2014-0641D12.5.492.08PULL DIRECTION2X 6.3.25R7.282X MINIMUM RECOMMENDEDPANEL HOLES (SEE TABLE)3.5 0.05.138 .002D11.432X LATCH MOUNTINGHOLE (SEE TABLE)28.41.1217.84.1622.5 0.1.886 .004.79 MAX.354C3.5.1422.5.8915.62.615893.568.52.7963.7826 MIN1.0245.2MIN17.5.69MAXC13.5.53SEE NOTE B6.6.2614.220.79MINB281.1.5620.8PANEL PREPARATIONB.8228.71.13ANOTES:A. MATERIAL AND FINISH:- HOUSING, LEVER AND INTERNAL COMPONENTS:MATERIAL: STEELFINISH: -10 = ZINC PLATED, BRIGHT CHROMATE-77 = ZINC NICKEL, BRIGHT CHROMATE- PAWL AND TRIGGER:MATERIAL: HARDENED STEEL,FINISH: -10 = ZINC PLATED, BRIGHT CHROMATE-77 = ZINC NICKEL, BRIGHT CHROMATE- SPRING: STAINLESS STEEL, PASSIVATEDB. THESE DIMENSIONS REQUIRED FOR MOUNTING STRIKER BOLT.SURFACE AREAVOLUMER4-10-21-201-77 1 4-20 THREAD 6.8 [.268]R4-10-20-201-10 7.2mm THRU 7.6 [.299]R4-10-21-201-10 1 4-20 THREAD 6.8 [.268]R4-10-22-201-10 M6 THREAD 6.4 [.252]ASSEMBLY PART NUMBER LATCH MOUNTING HOLE MINIMUM RECOMMENDED PANEL HOLEPROPRIETARY ITEMEXCEPT FOR USES EXPRESSLY GRANTEDIN WRITING, INFORMATION DISCLOSEDHEREON IS CONFIDENTIAL AND ALLRIGHTS, PATENT AND OTHERWISE,ARE RESERVED BY SOUTHCO, INC.THIRD ANGLEPROJECTIONMILLIMETERS [IN]DESCRIPTIONTOLERANCES UNLESS OTHERWISE NOTEDALL DIMENSIONS WITHOUTTOLERANCES ARE FORREFERENCE ONLY.PER ASME Y14.5M-1994SIZEBDRAWN BYSYSTEMNXDATECONNECT CREATE INNOVATER4 MINI ROTARY LATCHINLINE - LEFT HANDDWG NO.J-R4-10-20-201SCALERSHEETACH/JCK 09DEC2010 1:1 1 OF 3A654321

654321REVISION HISTORYREV DATEBYDESCRIPTIONE 04APR2014 CMS/BGL PRN: P2014-0641D371.46DPULL DIRECTIONPANELDOORC75.93C15.676 MAXNOMINAL7 MAXB16.3 0.5STRIKER BOLT(SOLD SEPARATELY,SEE R4-90-121-10FOR DETAILS)MISALIGNMENT VIEW(SEE NOTE B)BR4-10-21-201-77 1 4-20 THREAD 6.8 [.268]R4-10-20-201-10 7.2mm THRU 7.6 [.299]ANOTES:A. THE TOLERANCE BETWEEN THE LATCH AND STRIKER BOLT ASSUMES A NON-RIGID DOORINSTALLATION THAT WILL ALLOW THE DOOR TO MOVE INTO THE NOMINAL POSITIONDURING LATCHING. RIGID DOORS MUST HAVE THE STRIKER INSTALLED PER THE PANELPREPARATION RECOMMENDATION.B. THE MISALIGNMENT VIEW ASSUMES THE LATCH IS CONNECTED TO A PERFECTLY RIGIDDOOR AND HINGE; THEREFORE, THERE IS NO DOOR AND/OR HINGE SLACK ASSOCIATEDWITH THESE DIMENSIONS. THE MISALIGNMENT VIEW DOES NOT TAKE FLEXING OF THESTRIKER BOLT INTO ACCOUNT.SURFACE AREAVOLUMER4-10-21-201-10 1 4-20 THREAD 6.8 [.268]R4-10-22-201-10 M6 THREAD 6.4 [.252]ASSEMBLY PART NUMBER LATCH MOUNTING HOLE MINIMUM RECOMMENDED PANEL HOLEPROPRIETARY ITEMEXCEPT FOR USES EXPRESSLY GRANTEDIN WRITING, INFORMATION DISCLOSEDHEREON IS CONFIDENTIAL AND ALLRIGHTS, PATENT AND OTHERWISE,ARE RESERVED BY SOUTHCO, INC.THIRD ANGLEPROJECTIONMILLIMETERS [IN]DESCRIPTIONTOLERANCES UNLESS OTHERWISE NOTEDALL DIMENSIONS WITHOUTTOLERANCES ARE FORREFERENCE ONLY.PER ASME Y14.5M-1994SIZEBDRAWN BYSYSTEMNXDATECONNECT CREATE INNOVATER4 MINI ROTARY LATCHINLINE - LEFT HANDDWG NO.J-R4-10-20-201SCALERSHEETACH/JCK 09DEC2010 1:1 2 OF 3A654321

654321REVISION HISTORYREV DATEBYDESCRIPTIONE 04APR2014 CMS/BGL PRN: P2014-0641DOPTIONAL LINK RETAINERPART NUMBER R4-0-43922(SOLD SEPARATELY)DCABLE ASSEMBLYSEE J-AC-C(CABLE SHOWN WITHCABLE FITTING "B" INA CABLE ASSEMBLY "13)CCBOPTIONAL CABLE ASSEMBLYMOUNTING BRACKETPART NUMBER AC-900-02-10(SOLD SEPARATELY)BASURFACE AREAVOLUMER4-10-21-201-77 1 4-20 THREAD 6.8 [.268]R4-10-20-201-10 7.2mm THRU 7.6 [.299]R4-10-21-201-10 1 4-20 THREAD 6.8 [.268]R4-10-22-201-10 M6 THREAD 6.4 [.252]ASSEMBLY PART NUMBER LATCH MOUNTING HOLE MINIMUM RECOMMENDED PANEL HOLEPROPRIETARY ITEMEXCEPT FOR USES EXPRESSLY GRANTEDIN WRITING, INFORMATION DISCLOSEDHEREON IS CONFIDENTIAL AND ALLRIGHTS, PATENT AND OTHERWISE,ARE RESERVED BY SOUTHCO, INC.THIRD ANGLEPROJECTIONMILLIMETERS [IN]DESCRIPTIONTOLERANCES UNLESS OTHERWISE NOTEDALL DIMENSIONS WITHOUTTOLERANCES ARE FORREFERENCE ONLY.PER ASME Y14.5M-1994SIZEBDRAWN BYSYSTEMNXDATECONNECT CREATE INNOVATER4 MINI ROTARY LATCHINLINE - LEFT HANDDWG NO.J-R4-10-20-201SCALERSHEETACH/JCK 09DEC2010 1:1 3 OF 3A654321