rmk-fs and associated parts - Seacon

RMK-FS AND ASSOCIATED PARTSSTANDARD RUBBER MOLDEDIN-LINE SERIESNote: Available with grippers, must specify.Material: Special Neoprene, MoldedContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 psiVISUAL INDEX(IN-LINE WITH CONTACT #1)VISUALINDEX1.633.132.75∅1.06∅1.062.6RMK-MPSEALINGSURFACERMK-FS2.31RMK-FS R/A12123124312543126541326517 234675184238127 9365 41812 27936 11 105 4RMK-1/0-FS RMK-1-FS1 #1/0 1 #8 AWG(Cable: 1/0 Welding) (Cable: 8/1SO)WOC CONNECTORSRMK-6/8-FS1 #6 AWG1 #8 AWG(Cable: 8/2SO)RMK-2-FS1 #10 AWG1 #14 AWG(Cable: 18/2SO)RMK-3-FS1 #10 AWG2 #14 AWG(Cable: 18/3SO)RMK-4-FS1 #10 AWG3 #14 AWG(Cable: 18/4SO)RMK-5-FS1 #10 AWG4 #14 AWG(Cable: 18/5SO)RMK-6-FS1 #14 AWG5 #16 AWG(Cable: 18/6SO)RMK-7-FS1 #14 AWG6 #16 AWG(Cable: 18/7SO)RMK-8-FS1 #14 AWG7 #16 AWG(Cable: 18/8SO)RMK-9-FS1 #14 AWG8 #16 AWG(Cable: 18/10SO)RMK-12-FS1 #14 AWG11 #16 AWG(Cable: 18/12SO)Note: WOC stands for “without cable.” The connectors are supplied as shown below for installation in the field and/or to non-neoprenejacketed cables. Bonding can be achieved by molding to the connectors shown using polyurethane with appropriate primers.Inexpensive plastic syringes can be used as molds.Part Names: RMK-FS WOC, RMK-MP WOCMaterial: Special Neoprene, MoldedContacts: Brass, Hard Gold Plated per ASTM-B-488Voltage Rating: 600 VDC-contact factory for higher voltage requirementsPressure Rating, Mated: up to 20,000 psi21213124312541326512346517234178654238 127 93645718 12 911 106 5234RMK-1/0-FS1 #1/0RMK-1-FS1 #8 AWGRMK-6/8-FS1 #6 AWG1 #8 AWGRMK-2-FS1 #10 AWG1 #14 AWGRMK-3-FS1 #10 AWG2 #14 AWGRMK-4-FS1 #10 AWG3 #14 AWGRMK-5-FS1 #10 AWG4 #14 AWGRMK-6-FS1 #14 AWG5 #16 AWGRMK-7-FS1 #14 AWG6 #16 AWGRMK-8-FS1 #14 AWG7 #16 AWGRMK-9-FS1 #14 AWG8 #16 AWGRMK-12-FS1 #14 AWG11 #16 AWGLOCKING SLEEVESDUMMY CONNECTORSK-MLS-D (AVAILABLE FOR RMK-MP & RMK-MP WOC)K-FLS-D (AVAILABLE FOR RMK-FS, RMK-FS-R/A, RMK-FS WOC)K-MLS-S (AVAILABLE FOR RMK-MP, RMK-MP WOC)K-FLS-S (AVAILABLE FOR RMK-FS, RMK-FS R/A & RMK-FS WOC)K-FLS-X (AVAILABLE FOR RMK-FS)(Must specify cable O.D. when ordering K-FLS-X)Note: specify number of conductors when orderingRMK-FSD MATES TO RMK-MPRMK-MPD MATES TO RMK-FS & RMK-FS-R/AMaterial: Special Neoprene, MoldedPressure Rating, Mated:RMK-FSD (20,000 PSI)RMK-MPD-LP (LOW PRESSURE < 4,000 PSI, NO CONTACT REQUIRED)RMK-MPD-HP (4,000-20,000 PSI CONTACT IS REQUIRED)50-26 (REV 0704)

RMK-FS AND ASSOCIATED PARTSMATEABLE BULKHEAD CONNECTORSBULKHEAD CONNECTORS(MATES TO RMK-FS & RMK-FS-R/A & RMK-FS WOC)Dummy Connector: RMK-FSDNOTE:Torque values referenced in this literature assumeinstallation into dry metal threads. Please contact thefactory for recommendations.Part Name: RMK-BCLMaterial: 316 Stainless St.; Internal Insulation: Special NeopreneContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure rating, Mated: up to 20,000 psiRMK-BCL; Special Insulating neoprene is permanently moldedto the metal shell. These types of connectors are used wherephysical abuse would be too great for the non-metallic (glassreinforced epoxy) series. The RMK BCL has a locking sleeveprovision and utilizes a facial O-ring seal to the bulkhead.Part Name: XSK-BCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psiXSK-BCL; One of our oldest connectors in the non-metallicseries, with male pin as shown. Connector is one homogeneouslymolded unit. Available with different thread lengths as indicated.TheXSK BCL has a locking sleeve provision and utilizes a facialO-ring seal to the bulkhead.VISUAL INDEX(IN-LINE WITH CONTACT #1)VISUAL INDEX(IN-LINE WITH CONTACT #1)Mounting Torque130 inch lbs.Mounting Torque130 inch lbs.1-14 UNS.87 .87RMK-BCL1-14 UNSXSK-BCLVISUAL INDEX(IN-LINE WITH CONTACT #1)Mounting Torque130 inch lbs.1.25VISUALINDEX1-14 UNSXSK-BCL LT668898125510XSK-1/0-BCL1 #1/0RMK-1-BCLXSK-1-BCL1 #8 AWGRMK-6/8-BCLXSK-6/8-BCL1 #6 AWG1 #8 AWGRMK-2-BCLXSK-2-BCL1 #10 AWG1 #14 AWGRMK-3-BCLXSK-3-BCL1 #10 AWG2 #14 AWGPart Name: XSK-DEBCLMaterial: Glass Reinforced EpoxyContacts: Copper Alloy, Hard Gold Plated per ASTM-B-488Pressure Rating, Mated: up to 20,000 psi from front side.RMK-4-BCLXSK-4-BCL1 #10 AWG3 #14 AWGRMK-5-BCLXSK-5-BCL1 #10 AWG4 #14 AWGRMK-6-BCLXSK-6-BCL1 #14 AWG5 #16 AWGRMK-7-BCLXSK-7-BCL1 #14 AWG6 #16 AWGRMK-8-BCLXSK-8-BCL1 #14 AWG7 #16 AWGRMK-9-BCLXSK-9-BCL1 #14 AWG8 #16 AWGRMK-12-BCLXSK-12-BCL1 #14 AWG11 #16 AWGXSK-DEBCL; A non-metallic double ended connector whichaccepts a mating connector on either end. The same lockingsleeve also mates to both ends. This connector utilizes a facialo-ring seal to the bulkhead.LOW PRESSUREHIGH PRESSUREO-Ring (2-131)XSK-DEBCLVISUALINDEX6655XSK-1/0-DEBCL1 #1/0XSK-1-DEBCL1 #8 AWGXSK-6/8-DEBCL1 #6 AWG1 #8 AWGXSK-2-DEBCL1 #10 AWG1 #14 AWGXSK-3-DEBCL1 #10 AWG2 #14 AWGXSK-4-DEBCL1 #10 AWG3 #14 AWGXSK-5-DEBCL1 #10 AWG4 #14 AWGXSK-6-DEBCL1 #14 AWG5 #16 AWGXSK-7-DEBCL1 #14 AWG6 #16 AWG50-27 (REV 0704)