RS-NAGU.2f - automation-safety

More documents

Recommendations

Info

Application and functionIntroductionThe muting controller RS-NAGU.2f is used in conjunction with safety light barriers orsafety light grids to safeguard danger areas and danger points up to category 4 to EN13849-1. The integrated muting function to EN 61496 permits goods to be transportedinto or out of the danger area without impairment to the safety function.The device is suitable and tested for connection to safety light barriers and light gridsfrom a wide range of different manufacturers. A current list of tested light grids / lightbarriers and the relevant wiring instructions are provided in the "Applications"brochure. Should you not find the safety light barrier or safety light grid you wish touse in this list, please contact us by telephone.The diagram below provides an initial impression of connection possibilities. In thesection "Installation and commissioning", step-by-step instructions are provided onelectrical connection of the muting controller.BWS+24V GNDVCCGNDVCCGNDO1O2MS1+MS1PMS1NMS1-MS2+MS2PMS2NMS2-MS3+MS3PMS3NMS3-MS4+MS4PMS4NMS4-ERK+ERK131433342324A1+ESTEST+ESSESS+53AMLA1+6364A2BWS2PBWS1PA2-BWS1NBWSE-BWS2NA2-A1+ResetStartKey switchMuting lampMuting sensorsK2K1Bridge in case of no extensions contactors24 V DCK1GNDGND24 V DCK2Safety outputs with extension andfeedback circuitDevice typesType Description Order numberRS-NAGU.2f Device with fixed terminal strips AR.9667.9020RS-NAGU.2f - 270912 4/16
OutputsThe muting controller has the following outputs:• Three safety relay outputs (13-14, 23-24, 33-34) as n.o. contacts.• One signal output (73-74) as a n.o. contact. The signal output connects as long asthe muting is active.• Two optocoupler outputs (OP-O1, OP-O2)OP24 V DCO1Optocoupler output O1 switches to 24V when the safety outputs are active. Optocoupleroutput O2 switches to 24V when the connected safety light barrier is not delivering asignal. This can be the case when the device is switched off or in the muting mode,provided there are moving objects located in the area of the safety light barrier.DisplayFive LED’s are used to indicate status.MS1+ MS1N MS1PMS1- BWS1N BWS1POPO1O2A1+A1+ ESS+ ERK+ ERK MS2+ MS2N MS2P MS2- 13 23 33 53 631Netz StörungPower 2 Fault 34Kanal 1Channel1 5Kanal 2Channel2AMLPERS-NAGU.2..ESS EST+ EST BWSE+ BWSE- MS4+ MS4N MS4P MS4- 14 24 34 54 64 A2- A2-MS3+ MS3N MS3P MS3+ BWS2N BWS2P 73 741 Power ON2 Fault3 Restart inhibit on, waiting for start4 Operation – Channel 1 activated5 Operation – Channel 2 activated4+5 flashing Error codeFunctionAfter applying the supply voltage, the device performs a self test. LED’s 1,3,4 and 5light up and the device can be activated by pressing the start button.If the self-test has not been successfully executed, there is a fault or a connectionerror. For details, see the section "Troubleshooting" on page 15.If it is not possible to start the device by pressing the start button, at least one of themuting sensors is blocked or incorrectly connected. In the case of blocked mutingsensors, see the section "Muting components and function".RS-NAGU.2f - 270912 5/16
Page 1 and 2: Original operating instructions for
Page 3: Safety instructionsIntended useThe
Page 7 and 8: Muting sensorsMechanical, inductive
Page 9 and 10: Terminals1234MS1+ MS1N MS1PMS1- BWS
Page 11 and 12: WiringBWSThe precise wiring of the
Page 13 and 14: Wiringfeedback circuitUsing the fee
Page 15 and 16: Fault diagnosticsBC Fault Possible
Page 17: Ihr Kontakt zu riese electronic / y

RS-NAGU.2f - automation-safety

Create successful ePaper yourself

Delete template?

Save as template?