SECURA KEY CARD ACCESS CONFIGURATION GUIDE Single ...
SECURA KEY CARD ACCESS CONFIGURATION GUIDE Single ...
SECURA KEY CARD ACCESS CONFIGURATION GUIDE Single ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>SECURA</strong> <strong>KEY</strong> <strong>CARD</strong> <strong>ACCESS</strong> <strong>CONFIGURATION</strong> <strong>GUIDE</strong><strong>Single</strong>/Multi-Reader Systems with SK-ACP Two-Door PanelSK-ACP PANEL SYSTEM USING SK-NET TM SOFTWAREWITH RS-232 GATEWAY CONNECTED DIRECTLY TO A PCUP TO 500 Ft.SK-NET TMSOFTWARE¿2RS-232 GATEWAYRS-232UP TO 100 Ft.¿2SK-ACPSK-ACP<strong>CARD</strong> READER WITH ANY <strong>CARD</strong>TECHNOLOGY, WIEGAND OUTPUT,UP TO 40 BITSSK-ACP PANEL SYSTEM USING SK-NET TM SOFTWAREWITH RS-232 TO RS-485 CONVERTER (NET-CONV-P)SK-NET TMSOFTWARE¿2¿NET-CONV-PRS232-RS485CONVERTERUP TO 4,000 Ft.RS-485UP TO 500 Ft.2<strong>CARD</strong> READER WITH ANY <strong>CARD</strong>TECHNOLOGY, WIEGAND OUTPUT,UP TO 40 BITS1SK-ACPMULTI-PANEL SYSTEM USING SK-NET TM SOFTWARE- SINGLE LOCATION RS-232 CONNECTIONDAISY CHAIN / MULTIDROPSTAR /FANOUTSK-ACP“T”CONFIGSK-ACPSK-NET TMSOFTWARE¿2SK-ACPSK-ACP1SK-ACPSK-ACP¿1SK-ACPSK-ACP SK-ACPSK-ACP12NETWORK CABLE:RS-485 communications. Suggested cable: CAT 5network cable or Two Twisted Pair. Total system cablelength: 4,000 ft.SERIAL CABLE:RS-232 communications. Suggested cable: 6-Conductor,Shielded, with no twisted pairs. PC or serial printer. Totalcable length 100 feet. NOTE: Same wire to be used forconnection from SK-ACP to reader. Total cable length500 feet.SK-ACPSTUBBED¿2SERIAL PRINTERMONITORS ALL SYSTEMACTIVITYNOTE: Each SK-ACP above can support 2 Wiegand output card readers.
¿¿MULTI LOCATION SYSTEM WITH SK-NET-MLD SOFTWARESK-ACP1Up to 100SK-ACP’sSK-ACP¿SK-ACP1¿NET-CONV-PSK-NET TMSOFTWAREMODEMTELCO LINESK-MDMRS-232GATEWAY¿SK-ACP2 1A virtually unlimited number of remote locationscan be set-up on one PC with SK-Net-MLD Software.¿¿SK-ACPSK-ACPUp to 100SK-ACP’s¿NETWORK WIRING CONNECTIONSSK-ACP¿¿Line ALine BMULTI-PANEL SYSTEM USING SK-NET TM SOFTWARE- SINGLE LOCATION RS-485 with CONVERTERSK-NET TMSOFTWARE¿2NET-CONV-PRS232-RS485CONVERTER¿11SK-ACP SK-ACP SK-ACPSK-ACP12NETWORK CABLE:RS-485 communications. Suggested cable: CAT 5network cable or Two Twisted Pair. Total system cablelength: 4,000 ft.SERIAL CABLE:RS-232 communications. Suggested cable: 6-Conductor,Shielded, with no twisted pairs. PC or serial printer. Totalcable length 100 feet. NOTE: Same wire to be used forconnection from SK-ACP to reader. Total cable length500 feet.¿SERIAL PRINTERMONITORS ALL SYSTEM ACTIVITYNote: When using the RS-232 to RS-485 converter, you cannotuse the stubbed, star fanout or “T” configuration. All networkconnections from SK-ACP to the next SK-ACP must be in parallelwith each other. The J8 connector, Pins 1 and 2 must be a twistedpair. Pin 3 (Ground) is NOT normally connected, but if required canuse 1 conductor of a second pair.2
MULTI-PANEL SYSTEM USING SK-NET TM SOFTWARE- SINGLE LOCATION WITH SK-LANNOTE: SK-NET-MLD software must be used when connecting the SK-LAN External Device Server.SK-NET TMSOFTWARE¿3SK-LAN EXTERNALDEVICE SERVER¿2DAISY CHAIN / MULTIDROPSK-ACPSK-ACP1SK-ACPSTAR /FANOUTSK-ACPSK-ACP“T”CONFIGSK-ACP¿SK-ACP SK-ACPSK-ACP1SK-ACP123NETWORK CABLE:RS-485 communications. Suggested cable: CAT 5network cable or Two Twisted Pair. Total system cablelength: 4,000 ft.SERIAL CABLE:RS-232 communications. Suggested cable: 6-Conductor,Shielded, with no twisted pairs. PC or serial printer. Totalcable length 100 feet. NOTE: Same wire to be used forconnection from SK-ACP to reader. Total cable length500 feet.ETHERNET CABLE:Standard ethernet cable connector connected to existingLAN.SK-ACPSTUBBEDNOTE: Each SK-ACP above can support 2 Wiegand output card readers.¿2SERIAL PRINTERMONITORS ALL SYSTEMACTIVITY
SYSTEM EQUIPMENT COMPONENTS<strong>ACCESS</strong> CONTROL UNIT:SK-ACP: Two Door Access Control UnitRadio Key ® Low Frequency ProximityREADERS:RK-WM: Proximity Reader (2 readers per SK-ACP)RK-WS: Proximity Reader (2 readers per SK-ACP)RK-WL: Proximity Reader (2 readers per SK-ACP)<strong>CARD</strong>S/TAGS:RKCM-02-2RKKT-02-2RKCI-02-2Molded Proximity CardsKey TagsISO Proximity CardsE*Tag ® High Frequency Proximity:READERS:ET4-WXM: 13.56 MHz ISO 15693, MullionET4-WXS: 13.56 MHz ISO 15693, SwitchplateET8-RO-W-D: 13.56 MHz ISO 15693, SwitchplateET8-RO-W-M: 13.56 MHz ISO 15693, Mullion<strong>CARD</strong>S/TAGS:ETCI04-1- ISO Card- 26/32 bit encodingETCI04-4- ISO Card- 26/32 bit encoding, Mag-StripeETST03-1-Key Tag Trapezoidal - 26/32 bit encodingETKT03-1 Key Tag, Rounded End, 26/32 bit encodingPC REQUIREMENTS: See TableMINIMUM REQUIREMENTS*OPERATING SYSTEMPROCESSORAVAILABLERAMSPEEDDISK SPACEWINDOWS ® XP (32 bit) 1 GHz 1 GB 1 GBWINDOWS ® VISTA (32 bit) 1 GHz 1 GB 1 GB* For larger installation more disk space may be required.RECOMMENDED SYSTEMWINDOWS ® XP 2 GHz 2 GB 10 GBWINDOWS® VISTA 2 GHz 2 GB 10 GBIf using Vista, Aero-capable discrete graphics card with 128 MB Graphics Memory.SERVER REQUIREMENT**WINDOWS® 2000OR GREATER2 GHz 1 GB 1 GB** For SK-NET-MLD-C/S version, a server is required.SOFTWARE:SK-NET- DM — Basic Software - CD-ROM and manualSK-NET -MLD — Multi-Location Software with CD-ROM and manualSK-NET-MLD - CSXX (XX= 2,5,10 or 15 workstations) with Client Server License<strong>ACCESS</strong>ORIESNET-CONV-P — RS-232 to RS-485 Converter with Power Supply (12 VDC@100mA)one required per system (unless using a gateway connection)SK-QUICKCONN — Cable & Connector - For Bench Testing or field connection with a laptopSK-MDM — Modem - 56K Baud External Modemfor dial-up connection to any SK-ACPSK-LAN — TCP/IP External Device Server w/ Power Supply
Change language