SpxialUse Interchangeable Handptbces 0rder by part Number shown in Red,LH.l5 $133 Hammef 6h" tons, i/4" dia at tip, wt. 3.6s oz., ship wt 48s oz.Our hammer handpiece has a reciprocating rather than rotary action and is used atlow speed (0-5,000 rpm) by jewelers for stone setting and de<strong>co</strong>rative work. lt requiresoeriodic lubrication.The hammer has a 1/32" stroke and its impact force can be adjusted from lightoheavy by turning the silver knurled adjusting ring. lt <strong>co</strong>mes with an Anvil Point (10177)and pin for installing and tightening points.A Pav6 Point (R15PT) for special texturingand Stylus with Carbide Tip (10212) for marking or scribing hardened steel areavailable separately.nr+r*MAnvil PointOptional Pav6 PointHP10177 $4.00 A-Rl5PT 519,50Threads on these tools are 4-48 US threadInterchangeableHandpreces withDuplex Springs0rder bv Model Number in Rednnl@EOptional Carbide StylusHPr0212 $29.00H.8D $reH.l0D $24eH.25 $rso Heavy Duty5%" long, 11h2" dia.,wt.7.15 oz., ship wt. 9.6 oz.A precision, <strong>co</strong>lletstyle handpiece made for <strong>co</strong>ntinueus production work. The 25has double shielded ball bearings and a heavier duty housing than our regularinterchangeable handpieces.The 25 <strong>co</strong>mes with 1r8" (3.18mm) and 1/4" (6.35mm) <strong>co</strong>llets, and pin and chuckwrench. Other fractional and metri<strong>co</strong>llets are available separately and in ColletSet 103000 (page 17), (25C chuck style hear.ry duty model has been dis<strong>co</strong>ntinued.)See 8 Handpiece for full description.93/a" long,5/8" dia., wt. 5.2 oz., ship wt.7.35 oz.See 10 Handpiece for full description.103h" long,21l32" dia., wt.5.95 oz., ship wt.7.4 oz.<strong>Foredom</strong> offers eight handpieceswith Duplex Springs, denoted by theletter'D' at the end of each oart number.The spring <strong>co</strong>nnects the two separated endsof a handpieceis all that distinguishesthese handoieces from standard models.The duplex spring <strong>co</strong>mponent requiresoeriodic lubrication.Duplex Springs providextra flexibility to ahandpiece when more precise <strong>co</strong>ntrol for delicatework is required. The spring drive is made of specialsteel, double wound, tubular <strong>co</strong>nstruction with aprotective flexible spring <strong>co</strong>ver. Replacement springs(Part No.76, see page l7) are available and can beinstalled by the user.Duplex springs are subjecto breakageand are not <strong>co</strong>vered by warranty,We re<strong>co</strong>mmend that only experienced users offlex shaftools and/or those whose work demandsadded flexibility <strong>co</strong>nsider this style handpiece.H.l50 $r53H.l8D $160H.20D $10eH.52D $r60See 15 Handpiece for full description.9s/a" long, 1/4" dia. at tip, wt. 5.2 oz., ship wt 715 oz.See 18 Handoiece for full descriotion.10%" long, 19132" dia., wt. 5.3 oz., ship wt.6.85 oz.See 20 Handpiece for full description.10%" long, 11ls" dia. (center), 3/8" dia. (frontaper)wt. 5.4 oz., ship wt. 7.5 oz.See 52 Handpiece for full description10" long, 51i64' dia., wt. 5.15 oz., ship wt. 8.4 ozH.55D $r0eSee 55A Handpiece for full description.9%" Iong,7116" dia., max. hea dimension 5/8", wt.3.75 oz., ship wt. 5.8 oz.H,56D $10eSee 56A Handpiece for full description.g1/2" long,1116" dia., max. hea dimension 5E",v,tt 4 oz., ship wt. 6.05 oz.12
..tSpecial Use lnterchangeable Handpr'eces 'rderby parr Number shown in Red'f ,$fp]f,{!jfr f'3;{$""!:; st-;tlry'., .=-u'e $udH.35 $tzg Speed IncreasingRe<strong>co</strong>mmended for usewith Series TX motors5%" long, 1%s" dia., wt.8 oz., ship wt. 10.3 oz.This unique handpiece has a ball bearing speed increaser that produces 2,5 timesthe speed of the motor. lhis feature makes it perfect for bright cutting with diamondflywheels and other high speed work with carbide and diamond points.The 35 <strong>co</strong>mes with a 1,E" (3.18mm) <strong>co</strong>llet installed unless otherwise specified. Otherfractional and metri<strong>co</strong>llets available separately and in Collet Set 103000(page 17).Note: The No. 35 handpiece should not beoperated at speeds faster than 35,000 rpm.When <strong>co</strong>nnected to your standard <strong>Foredom</strong>otor(that runs up to 18,000rpm), motor speed must bekept at 14,000 rpm or less (7590 of full no-loadspeed)" We re<strong>co</strong>mmend using the 35 with thepowerful TXM bench-style motor whic has a built-indial <strong>co</strong>ntrol, or theTX hang-up model with the EMXdial <strong>co</strong>ntrol for setting and holding speed to within35,000 rpm range. Another option is using astandard motor with an EM dial <strong>co</strong>ntrol.H.55A $89 ta" <strong>co</strong>ntra-angle handpiece is good for intricate and delicate jobsin awkward and hard-to-reach spots.6%" long,7116" dia., max. hea dimen.5i8",wt.2.1 oz., ship wt.3.5 oz.54" (16mm)H.56A $89 similar to the 55A except that iihas a righrangle head.61/8" long,7116" dia., max. hea dimen.5/8", wt.2.35 oz., ship wt.3.7 oz.Angle Head for latch-type accessoriesAngle head handpieces are for light and intermittent work and the miniature gearsin their heads require frequent lubrication.They <strong>co</strong>me with wrro latch-type mandrels.Can also be used with latch-type steel burt mounted abrasive points, and diamondpoints available from <strong>Foredom</strong>- see Accessory <strong>Catalog</strong> or visit vrnrwv.foredom.<strong>co</strong>m.Changing latch-type Use for a wide variety of light-duty jobsaccessories is easy...iustin hard-to-reach areas:turn the iatch to open .and close the <strong>co</strong>llet.debuning, finishing and polishing metals. removing oxidation andcleaning electrical andelectronic <strong>co</strong>ntacts. removing flux <strong>co</strong>atingsfrom PC boards. reworking and repairingcircuit boardsSlip loint Handptecgs for European Machines orderbypartNumbershowninRedSlip joint handpieces will fit on all European made flexible shaft machines with"slipjoint""QD"<strong>co</strong>nnections. They cannot be used with the standard style flex shafton all <strong>Foredom</strong> flexible shaft machines. A European style flexible shaft and sheathis available to reolace the standard shaft and sheath on all <strong>Foredom</strong>achines.A special motor <strong>co</strong>upling is also required (see page 16).S-10810A European Style Shaft and Sheath . .$1 25.00UA540 European Motor Coupling and Connector Kit. .... 16.50S-10811 CompleteConversionAssembly(10810AandUA540)'135.00General PurposeQuick ChangeH.l8SJ $140Suitable for use only with 2.35nn (382") shank bursor mandrels. See 1 I Handpiece for full description.63/a" long,19132" dia., wt. 3.6 oz., ship vrrt.4.9 oz.H.8SJ$s9Comes with 2.35mm (3/32") and 3mm <strong>co</strong>llets, andchuck wrench set. See 8 Handpiece for full description51/2" long,5l8" dia,, wt. 3,5 oz., ship wt,4.65 oz.H.20SJ $8eSuitable for use only with 2.35mm (3/32") shank burs ormandrels. See 20 Handpiece for full description.51/2" long,51164" dia., wt. 2.95 oz., ship wt. 5.3 oz.H.28SJ $5eComes with 2.35mm (3/32") and 3mm <strong>co</strong>llets, and pinand chuck wrench set. See 28 Handoiece for fulldescription.5Ta" long, 3 | 4" dia., 112" dia. (taper),wt. 3 oz., ship wt. 4.70 oz.H.52SJ $140HammerSuitable for use only with 2.35mm (3132") shank burs ormandrels. See 52 Handpiece for full description.5t/2" long,51164" dia., wt, 2.95 oz., ship wt. 5.8 oz.H.30SJ$6sComes with geared 3-jaw #0 chuck with 0-4mm (5/32")capacity and CK-0 chuckey. See 30 Handpiece for fulldescription. 53h" long,1" dia., wt. 6.45 oz.,shio wt.9.55 oz.H.l5SJ $133Speed IncreasingComes with threaded anvil point and pin to tightenpoint. See I 5 Handpiece for full description.5%" long, l/4" dia. at tip, wt. 3.55 oz., ship wt.4.9 oz.UH.4ATSI $seLomes wltn l35mm l5l5l ), Jmm, ano bmm <strong>co</strong>llets,and pin and chuck wrench set. See 44T Handpiece forfull description. 61/4" long,1" dia. (center) 3/4" dia.(taped, wt. 6.75 oz., ship wt.9.04 oz.13H.35SJ S17g Comes with 3mm <strong>co</strong>llet unless otherwise specified.See 35 Handpiece for full description.6t/t" long, 13/rc" dia., wt. 9.45 oz., ship wt. 10.7 oz.