CE300372-A1 Ring shank nail coil - Gunnebo Industries

RING SHANK NAIL, COILHOT DIP GALVANIZEDDeclaration ofPerformanceDIMENSIONSDokument no: CE-300372-A1Used for fix boarding, panels andsecondary spaced boarding to a timberbaseDimensions:d: 2,5-31 mm L: 45-90 mmMaterial:EN ISO 16120-2Characteristic tensile strength of wire (fu) inacc. with EN 10218-1, min. 600 N/mm 2Treatment:Hot dip galvanized - min. 50 µmCoil:15° 17° 21°HOT DIP GALVANIZED2,5x45NameNominaldiameter d[mm]Total length L[mm]2,5 44,027,0Threaded lengthl g [mm]*Head diameterd h [mm]5,7Head area A h[mm²]Head thicknesst [mm]26,0 1,23,2Point length l p[mm]2,5x5049,032,02,5x5554,033,02,5x6059,042,02,5x6564,047,02,8x602,859,030,06,9371,33,42,8x7574,046,03,1x903,188,059,06,937,01,64,3*Total threaded length excluding two plain parts for coil wire 4+4 mm.CHARACTERISTIC LOAD CAPACITYHOT DIP GALVANIZEDNameNominaldiameter d[mm]Total length L[mm]Withdrawal parameterf ax,k [N/mm²]*Head pull-troughparameter f head,k[N/mm²]*Yield moment M y,k[Nmm]Tensile capasityf tens,k [kN]2,5x452,544,04,119,719003,22,5x5049,02,5x55 54,02,5x6059,02,5x6564,02,8x602,859,05,215,426003,92,8x7574,03,1x90 3,188,0----* The withdrawal parameter f ax,k and the head pull-through parameter f head,k is tested in wood with a characteristic density of ρ k =350kg/m 3 (C24). When wood with another density is used values shall be multiplied with ρk/350.2012-08-17, rev. 2013-02-01, Page 1 of 2 Dokument no: CE-300372-A1

RING SHANK NAIL, COILHOT DIP GALVANIZEDDeclaration ofPerformancePRODUCT IDENTIFICATIONFollowing articles which are sold in the brand name GUNNEBO FASTENING are covered by thisDeclaration of Performance:ARTICLE NUMBERZ776145 Z776160 Z794051 Z794065 Z724090Z776150 Z776165 Z724060 Z724076The manufacturer declares for:Ring shank nail coil 15°, hot dip galvanized, diameter 2,5 up to 2,8mm1. Product is in accordance with EN 14592:2008 “Timber Structures– Dowel-type fasteners – Requirements”.2. Initial Type Testing was performed to confirm essentialcharacteristic values in accordance to table ZA.1 in EN 14592. Declaredvalues accompanies with the CE mark on each package and in thistechnical document.3. Initial Typprovning är utförd av DTI, Danish TechnologicalInstitute. f tens,k in report DK 474099-1, Taastrup, 2012-04-27.M y,k in report DK 474099-2, Taastrup, 2011-04-27.f ax,k in report DK 474099-3, Taastrup, 2011-05-15.f head,k in report DK 474099-4, Taastrup. 2011-05-15.f u,k in report DK 1302213, Århus, 2012-04-26.4. For this product the compliance with the conditions of the AnnexZA in EN 14592 are accomplished.5. A FPC system is established and maintained under theresponsibilities of the manufacturer.Hot dip galvanized 50 µm.The system of attestation of conformity for Timber fasteners used forstructural timber products is 3.This declaration of conformity is valid until any changes in the product,the raw material or the production process is performed, which wouldsignificantly change the declared characteristics.Gunnebo 2012-08-17, revidert 2013-02-01.................................................................................Head of Operation, Claes ArnessonGBO Fastening systems ABBruksvägen 2SE 590 93 GunneboSweden2012-08-17, rev. 2013-02-01, Page 2 of 2 Dokument no: CE-300372-A1