Weldmatic 175 [internal wirefeeder] - BJH

More documents

Recommendations

Info

Operators ManualTipsWire diameter0.6mm0.8mm0.9mm1.0mm1.2mmShort series (25mm)BE7497BE7488BE7489BE7496BE7490To replace liner: Disconnect gun/cableassembly at the Euro adaptor. Removenozzle (1) and head (3). Withdraw oldliner from the wirefeeder end. Insert newliner and refit gun/cable assembly to thewirefeeder.At the gun end, compress the liner withinthe gun cable, then cut it one contact tiplength past the end of the body tube (5).Refit head, tip and nozzle.Cut HereCompress LinerFig 6 Replacing the gun cable liner24Quality • Reliability • Performance
Weldmatic 17512 Warranty InformationWIA Gold Shield 3 Year WarrantyEffective 1st March 2005At WIA, we are serious about productquality.Every new Weldmatic and Weldarcmachine comes fully backed by the WIA‘Gold Shield 3 Year Warranty’, coveringparts and workmanship, so you can beguaranteed you’re buying reliability andperformance.This limited warranty supersedes all previousWIA (Welding Industries of Australia)warranties and is exclusive with no otherguarantees or warranties expressed orimplied.Limited WarrantySubject to the terms and conditions below, WIAwarrants to its original retail purchaser that newWIA equipment sold after the effective date ofthis limited warranty is free of defects in materialand workmanship at the time it is shipped byWIA.THIS WARRANTY IS EXPRESSLY IN LIEU OFALL OTHER WARRANTIES, EXPRESS ORIMPLIED, INCLUDING THE WARRANTIES OFMERCHANTABILITY AND FITNESS.Within the warranty periods listed below,WIA will repair or replace any warrantedparts or components that fail due to suchdefects in material or workmanship. WIAmust be notified in writing within thirty (30)days of such defect or failure, at which timeWIA will provide instructions on the warrantyclaim procedures to be followed.WIA shall honour warranty claims onwarranted equipment in the event of such afailure within the warranty time periods. Allwarranty time periods start on the date thatthe equipment was delivered to the originalretail purchaser, or 18 months after theequipment date of manufacture, whicheveris the earlier.Parts and workmanship on Weldarcand Weldmatic equipment are coveredfor a period of 3 years (except for gasregulator, gun cable and consumableslisted below.)Items replaced under original warranty arewarranted for the remainder of the originalequipment warranty, or for a period of ninety(90) days, whichever is the greater.Gas regulator and gun/cable assembly arewarranted for 90 days.WIA’s Limited Warranty shall not apply to:1 Consumable components; such ascontact tips, cutting nozzles, contactors,brushes, relays or parts that fail due tonormal wear.2 Equipment that has been modified by anyparty other than WIA, or equipment thathas been improperly installed, improperlyoperated or misused based uponindustry standards, or equipment whichhas not had reasonable and necessarymaintenance, or equipment which hasbeen used for operation outside of thespecifications for the equipment.WIA PRODUCTS ARE INTENDED FORPURCHASE AND USE BY COMMERCIAL /INDUSTRIAL USERS AND PERSONS TRAINEDAND EXPERIENCED IN THE USE ANDMAINTENANCE OF WELDING EQUIPMENT.In the event of a warranty claim coveredby this warranty, the exclusive remediesshall be, at WIA’s option: (1) repair; orModel No CP122, Iss A 07/07 25
Page 5: Weldmatic 175Burn protectionThe wel
Page 8 and 9: Operators Manual3 SpecificationsMan
Page 10 and 11: Operators Manual5 InstallationConne
Page 12 and 13: Operators Manual6 Normal Welding Se
Page 14 and 15: Operators ManualWeldmatic 175Settin
Page 16 and 17: Operators Manualoperated with appro
Page 18 and 19: Operators Manual9 External Trouble
Page 20 and 21: Operators Manual10 Service Informat
Page 22 and 23: Operators Manual11.1 Assembly and P
Page 24 and 25: Operators Manual11.2 Assembly and P
Page 28: Operators Manual(2) replacement; or

Weldmatic 175 [internal wirefeeder] - BJH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?