SIMOVERT Master Drives Einspeise-Einheit Bauform B und C ...

More documents

Recommendations

Info

02.96 ConnectionUnit order No.Mains supply cable fusesColumn 1 Column 2 Column 3Siemens gR(SITOR)Preferred typeSiemens (SITOR)BussmannUS-standard6SE70 A Type A Type A Type24-1EB85-0AA0 63 3NE4118 63 170M361028-6EC85-0AA0 80 3NE1820-0 125 3NE3222 125 170M361324-1FB85-0AA0 63 3NE4118 63 170M369027-2FC85-0AA0 80 3NE1820-0 125 3NE3222 100 170M369228-8FC85-0AA0 100 3NE1021-0 125 3NE3222 160 170M3693Table 3.2Column 1:Column 2, 3:Recommended mains fusesThis fuse with gR characteristic protects the semiconductors. At the same time, they also haveline protection characteristic which can be used if the appropriate conductor cross-sections arechosen, e.g. in accordance with DIN VDE 0100 Part 430 (to be applied for preference).Semiconductor protection only, lines are not reliably protected. Discriminative line protection isassured only by correlating the line protection fuses to the installed conductor cross-section inaccordance with the applicable regulations - e.g. DIN VDE 0100 Part 430.Unit order No. Rated input- Commutation choke 2 %voltage current Type Voltage / Frequency Rated current6SE70 (V) (A) (V / Hz) (V / Hz) (A)24-1EB85-0AA0 380 to 460 36 4EP3700-2UK 400 / 50 460 / 60 35,528-6EC85-0AA0 380 to 460 74 4EP3900-2UK 400 / 50 460 / 60 8024-1FB85-0AA0 500 to 575 36 4EP3700-1UK 500 / 50 35,527-2FC85-0AA0 500 to 575 62 4EP3900-1UK 500 / 50 6328-8FC85-0AA0 500 to 575 82 4EP4000-1UK 500 / 50 80Table 3.3Recommended commutation chokeSiemens AG 67087-6AC85-0AA0 ENGLISH 3-3Common Rectifier Operating instructions
Connection 02.963.2 Power supply / control3.2.1 Electronic power supply / fault signalThe electronic power supply is not included in the scope of supply of the common rectifier.Plug-in terminal X9Terminal Function description perm. conductorcross-sectionX9 (mm2) (AWG)1 DC 24V (tolerance range 20V - 30V) 2)max. current consumption 2A at +24Vmax. current consumption without options:size B = 0.5A, size C = 1A0,2 to 2,5 24 to 14Table 3.32 Reference potential 0,2 to 2,5 24 to 143 not connected (N.C.) 0,2 to 2,5 24 to 144 Fault signal 2) 0,2 to 2,5 24 to 145 Fault signal 2) 0,2 to 2,5 24 to 14Permissible connection cross-sections for the power supply and the fault signalX9ext. SVDC 24VPMFault signal1 2 3 4 5AC 230V1500VAFigure 3.2 DC 24 V power supplyand fault signalconnectionTerminal X9.1 fused with fuse T2A/250V träge/time-lag 5x20mm(19198-T2A/250V Messrs. Wickmann-Werke GmbH respectively0034.3993 FSD Messrs. Schurter)Terminal X9.2 fused with fuse T3,2A/250V träge/time-lag 5x20mm(19198-T3,2A/250V Messrs. Wickmann-Werke GmbH respectively0034.3998 FSD Messrs. Schurter)WARNINGFor safety reasons, we recommend that a master contactor or other device with a similarfunction is fitted on the mains system side which disconnects the unit from the mainssystem when the "Fault" contact opens.In cases where a main contactor is fitted, a latching circuit should be provided for this inorder to prevent unexpected reclosing after faults.NOTESThe main contactor’s exciter coil must be wired with surge arresters, e.g. an RC network for AC or a diode forDC.The 'Fault' relay contact (terminal X9) must be looped directly or indirectly into the main contactor control. Useof a main contactor is necessary to protect the unit. Connection of a latching relay prevents unexpectedactivation when the fault is remedied.In the event of phase failure, operation of the main contactor without latching leads to cyclic deactivation andactivation of the main contactor because the phase failure signal is suppressed in the event of a mains failure.Mains failure on the unit arises by virtue of the fact that the main contactor drops out in the event of amalfunction.2) Contacts for switching the main contactor between terminals 4 and 5 ; switching voltage AC 230V max. AC 3A at cos 0.4; max.switching capacity 1500 VA ; at switching voltage DC 30V max. DC 5A3-4 ENGLISH Siemens AG 6SE7087-6AC85-0AA0Common Rectifier Operating instructions
Page 1: SIMOVERT Master DrivesEinspeise-Ein
Page 5 and 6: Contents 02.968 Maintenance .......
Page 7 and 8: Definitionen 10.94CAUTIONElectrosta
Page 9 and 10: Definitionen 10.940-8 ENGLISH Sieme
Page 11 and 12: Description 02.961-2 ENGLISH Siemen
Page 13: Transport, unpacking, assembly 02.9
Page 16 and 17: 02.96 Connection3 ConnectionWARNING
Page 20 and 21: 02.96 Connection3.2.2 Signalling re
Page 22 and 23: 02.96 Connection3.4 Measures for ke
Page 24 and 25: 02.96 Connection3AC 50-60Hz, 400V3A
Page 26 and 27: 02.96 Connection+ -U1/L1V1/L2W1/L3G
Page 28 and 29: 02.96 Start-up4 Start-upWARNINGThe
Page 30 and 31: 02.96 Start-upRated voltage U nchai
Page 32 and 33: 02.96 Malfunctions and warnings7 Ma
Page 34 and 35: 02.96 Maintenance8 MaintenanceWARNI
Page 36 and 37: 02.96 MaintenanceReplacing modules
Page 38 and 39: 02.96 Options9 Options9.1 A50 addit
Page 40 and 41: 02.96 Options9.3 Power SupplyA SITO
Page 42 and 43: 02.96 Spare parts10 Spare partsFor
Page 44 and 45: 02.96 Environmental compatibility13
Page 46: 02.96 Technical data14 Technical da
Page 49 and 50: Technical data 02.9614.3 Applied st
Page 51 and 52: Technical data 02.9614-6 ENGLISH Si
Page 53 and 54: Index 11.9415-2 Siemens AG 6SE7087-

SIMOVERT Master Drives Einspeise-Einheit Bauform B und C ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?