D - Tiger-Tools Kft.

More documents

Recommendations

Info

HIGH SPEED DRILLHSD-V Big diameter Drill(Cartridge type) STD-V DRILL Shank ISO9766, Parallel with clamping flatHSD-V 2XD CARTRIDGE TYPECODE NO. D L1 L Ds Ls INSERT SCREW DRIVER CARTRIDGEHSD-V596520D S40 59-65 130 240 HSC-V5965N/THSD-V657020D S40 65-70 140 250HSC-V6570N/T40 70 WC..06T308 TSB-35090 TXL-15HSD-V707520D S40 70-75 150 260 HSC-V7075N/THSD-V758020D S40 75-80 160 270 HSC-V7580N/THSD-V 3XD CARTRIDGE TYPECODE NO. D L1 L Ds Ls INSERT SCREW DRIVER CARTRIDGEHSD-V596530D S40 59-65 195 305 HSC-V5965N/THSD-V657030D S40 65-70 210 320HSC-V6570N/T40 70 WC..06T308 TSB-35090 TXL-15HSD-V707530D S40 70-75 225 335 HSC-V7075N/THSD-V758030D S40 75-80 240 350 HSC-V7580N/THSD-V 4XD CARTRIDGE TYPECODE NO. D L1 L Ds Ls INSERT SCREW DRIVER CARTRIDGEHSD-V596540D S40 59-65 260 370 HSC-V5965N/THSD-V657040D S40 65-70 280 390HSC-V6570N/T40 70 WC..06T308 TSB-35090 TXL-15HSD-V707540D S40 70-75 300 410 HSC-V7075N/THSD-V758040D S40 75-80 320 430 HSC-V7580N/T HSD-V drill will be sold after HSD drill is sold out. 26www.koreatechnics.com
HIGH SPEED DRILLThe setting procedures for the big dia drill(Cartridage type)HSD-V Cutting partClampimg bolt for Cartridge Outer Cartridge Loosen the clamping bolt of the outer cartridge and remove it from the drill body. Cut off the inside part, the contacted side of the outer cartridge by milling after calculating the drillingdiameter. Slick the sharp corner of the cut cartridge. Adhere the cartridge closely to the drill body not happen gap and fix the cartridge with bolt tightly. ExampleIf you set HSD-V707530D to 72 The standard drill diameter is 75 so 7572 = 3 32=1.5(calculation by semidiameter),1.5mm is cut off. KOREA TECHNICS is The TOP of the world technics 27
Page 1: http://www.koreatechnics.com
Page 5: HIGH SPEED DRILLConstruction System
Page 10 and 11: HIGH SPEED DRILLSTD-V 4D DRILL
Page 12 and 13: HIGH SPEED DRILLSTD-V Big diameter
Page 14 and 15: HIGH SPEED DRILLHSD-V 2D DRILL
Page 22 and 23: HIGH SPEED DRILLMCD 2D DRILL EX
Page 24 and 25: HIGH SPEED DRILLMCD 3D DRILL EX
Page 26 and 27: HIGH SPEED DRILLHSD 2D DRILL32w
Page 28 and 29: TURBO DRILLFXD 4D DRILL Shank
Page 30 and 31: TURBO DRILLFXD 8D DRILL Shank
Page 32 and 33: TURBO DRILLVLT 5D STANDARD TYPEDRIL
Page 34 and 35: TURBO DRILLVLT 6.5D STANDARD TYPEDR
Page 36 and 37: TURBO DRILLVLT 8D STANDARD TYPEDRIL
Page 38 and 39: TURBO DRILLTMD 5D
Page 40 and 41: TURBO DRILLTMD CARTRIDGE TYPE
Page 42 and 43: TURBO DRILLHSD 2D DRILL 48
Page 44 and 45: MAX DRILLVMD DRILL
Page 46 and 47: MAX DRILLDRILLThe drill body treate
Page 48 and 49: TREPANNING DRILLTPD 2.5D DRILL TPD
Page 50 and 51: MX HOLDERMXA/MXBMX HOLDER MX CYLIND
Page 52 and 53: MX HOLDERBT-MXA/BT-OMX/BT-OAXMX HOL
Page 54 and 55: MX HOLDERNT-MXA/NT-OMX
Page 56 and 57: BASIC HOLDER NEW TYPE ARBORBT-WSA/B
Page 58 and 59: BASIC HOLDER NEW TYPE ARBORSK-WSA/S
Page 60 and 61: BASIC HOLDER NEW TYPE ARBORNT-WSA/N
Page 62 and 63: BASIC HOLDER NEW TYPE ARBORMT-WSA/M
Page 64 and 65: BASIC HOLDER Surprising long life
Page 66 and 67: BASIC HOLDERBT-OMS/BT-OME
Page 68 and 69: BASIC HOLDERSK-SLA/SK-ETA DIN69871/
Page 70 and 71:
BASIC HOLDERNT-SLA/NT-ETA DIN2080/N
Page 72:
BASIC HOLDERMT-SLA/MT-ETA DIN228B/M
Page 76 and 77:
ACCESSORIESCARTRIDGE ACC
Page 78 and 79:
ACCESSORIESCARTRIDGE INNER O
Page 80 and 81:
ACCESSORIESPILOT DRILL/DRIVE RING/D
Page 82 and 83:
ACCESSORIESCLAMPING SCREWS FOR INDE
Page 84 and 85:
ACCESSORIESCLAMPING BOLTS FOR VLTAC
Page 88 and 89:
Technical Data
Page 90 and 91:
Technical Data
Page 92 and 93:
Technical Data
Page 94 and 95:
Technical Data ISOKorea United Ki
Page 96 and 97:
Technical Data ISOKorea United Ki
Page 98 and 99:
Technical Data Directions for the
Page 100 and 101:
Technical Data Directions for the
Page 102 and 103:
Technical Data TaperNo.L1mmDmmMmmK
Page 104 and 105:
Technical DataCYLINDRICAL SHANK TYP
Page 106:
Technical DataMX MODULAR SYSTEMTech
show all

D - Tiger-Tools Kft.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?