Vivotek MD7560 User Guide - Use-IP
Vivotek MD7560 User Guide - Use-IP
Vivotek MD7560 User Guide - Use-IP
- No tags were found...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Wall Mount1English2BA3Please secure the screws tightly toavoid moisture.4Installing the Ground WireAs shown in the following fi gure, please secure one side of the supplied ground wire to the screwhole, then route the other side of the ground wire to the ground.EN - 5
POWER CO LISION1 2 3 4 5LINKRECEIVEPARTITION4Network DeploymentGeneral Connection (without PoE) (MD7530D / <strong>MD7560</strong>D)1. If you have external DI devices, make the connection from general I/O terminal block.2. <strong>Use</strong> the supplied RJ45 female/female coupler to connect the Network Camera to a switch.<strong>Use</strong> a Category 5 Cross Cable when Network Camera is directly connected to PC.3. Connect the power cable from the Network Camera to a power outlet.+ : Digital input- : Digital inputEthernet Switch123EN - 6
POWER CO LISION1 2 3 4 5LINKRECEIVEPARTITIONPOWER CO LISION1 2 3 4 5LINKRECEIVEPARTITIONPower over Ethernet (PoE) (MD7530 / <strong>MD7560</strong>)When using a PoE-enabled switchThis Network Camera is PoE-compliant, allowing transmission of power and data via a singleEthernet cable. Follow the below illustration to connect the camera to a PoE-enabled switch viaEthernet cable.EnglishPoE SwitchWhen using a non-PoE switch<strong>Use</strong> a PoE power injector (optional) to connect between the Network Camera and a non-PoEswitch.PoE Power Injector(optional)Non-PoE SwitchEN - 7
5Assigning an <strong>IP</strong> Address1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.2. The program will conduct an analysis of your network environment. After your network is analyzed,please click on the “Next” button to continue the program.InstallationWizard 23. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Camerason the same LAN.4. After searching, the main installer window will pop up. Click on the MAC that matches the onelabeled on the bottom of your device to connect to the Network Camera via Internet Explorer.Network CameraModel No: MD7530MAC:0002D107258AV IRoHS00-02-D1-07-25-8A 192.168.5.151 MD75300002D107258AThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.Pat. 6,930,709Made in TaiwanEN - 8
6Ready to <strong>Use</strong>English1. Access the Network Camera on the LAN.2. Retrieve live video through a web browser or recording software.For further setup, please refer to the user's manual on the software CD.7Adjusting the LensTo adjust the viewing angleAdjust the lens to a desired viewing angle as the diagram shown below.90°DO NOT over rotate the lens. Doingso will damage the camera lensmodule.EN - 9
Fine-tune the Camera FocusThe focus of this network camera is set from 1.0m to infi nity by factory default. If you want to focuson objects closer than 1.0m or the lens has lost focus, please fi ne tune it in the following way.1. Loosen the lens lock screw.2. Manually rotate the lens to fi ne-tune the focusuntil the live image is clear.3. Tighten the lens lock screw.Tighten the lens lock screw.8CompletionTear down the aluminum foil vacuum bag andtake out the silica gel. Attach the supplied silicagel to the inner side of the Network Camera.(Please replace the silica gel with a new one ifyou open the back cover after installation.)Attach the dome cover to camera.Secure the dome screws with thesupplied screwdriver. Finally, make sureall parts of the camera are securelyinstalled.Please secure the screws tightly toavoid moisture.EN - 10
P/N:625011800G Ver1.0Copyright c 2010 VIVOTEK INC. All rights reserved.
Change language