Procedural Lab Template, Student Version, Required Components

More documents

Recommendations

Info

CCNA ExplorationAccessing the WAN: Skills Based AssessmentStudent Skills based Assessment LabDevice Interface IP Address Subnet Mask Default GatewayPC1 NIC 10.0.0.10 255.255.255.128 10.0.0.1PC3 NIC 10.0.0.139 255.255.255.128 10.0.0.129Learning ObjectivesTo complete this lab:• Cable a network according to the topology diagram• Erase the startup configuration and reload a router to the default state• Perform basic configuration tasks on a router• Configure and activate interfaces• Configure and activate serial interfaces (PPP with CHAP, HDLC, and Frame Relay)• Configure RIP on all the routers• Configure basic router security• Configure ACLs• Configure basic NATScenarioThis lab tests you on the skills and knowledge that you learned in Exploration 4. Use cisco for all passwords inthis lab, except for the enable secret password, which is class.Task 1: Prepare the NetworkStep 1: Cable a network that is similar to the one in the topology diagram.Step 2: Clear any existing configurations on the routers.Task 2: Perform Basic Device ConfigurationsConfigure the R1, R2, and R3 routers according to the following guidelines:R1:• Configure the router hostname.• Disable DNS lookup.• Configure an EXEC mode password.• Configure a message-of-the-day banner.• Configure a password for console connections.• Configure synchronous logging.• Configure a password for vty connections.Router>enableRouter#configure terminalRouter(config)#hostname R1R1(config)#banner motd #R1#R1(config)#no ip domain-lookupR1(config)#enable secret classAll contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 2 of 9
CCNA ExplorationAccessing the WAN: Skills Based AssessmentStudent Skills based Assessment LabR1(config)#line console 0R1(config-line)#password ciscoR1(config-line)#loginR1(config-line)#logging synchronousR1(config-line)#exec-timeout 5R1(config-line)#exitR1(config)#line vty 0 4R1(config-line)#password ciscoR1(config-line)#loginR1(config-line)#logging synchronousR1(config-line)#exec-timeout 5R1(config-line)#exitR2:Router>enableRouter#configure terminalRouter(config)#hostname R2R2(config)#banner motd #R2#R2(config)#no ip domain-lookupR2(config)#enable secret classR2(config)#line console 0R2(config-line)#password ciscoR2(config-line)#loginR2(config-line)#logging synchronousR2(config-line)#exec-timeout 5R2(config-line)#exitR2(config)#line vty 0 4R2(config-line)#password ciscoR2(config-line)#loginR2(config-line)#logging synchronousR2(config-line)#exec-timeout 5R2(config-line)#exitR3:Router>enableRouter#configure terminalRouter(config)#hostname R3R3(config)#banner motd #R3#R3(config)#no ip domain-lookupR3(config)#enable secret classR3(config)#line console 0R3(config-line)#password ciscoR3(config-line)#loginR3(config-line)#logging synchronousR3(config-line)#exec-timeout 5R3(config-line)#exitAll contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 3 of 9
Page 1: CCNA Exploration: Accessing the WAN
Page 5 and 6: CCNA ExplorationAccessing the WAN:
Page 7 and 8: CCNA ExplorationAccessing the WAN:
Page 9: CCNA ExplorationAccessing the WAN:

Procedural Lab Template, Student Version, Required Components

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?