SPECIFICATIONS FOR LCD MODULE

More documents

Recommendations

Info

11. Display Control InstructionFundamental Command TableD/C# Hex D7 D6 D5 D4 D3 D2 D1 D0 Command Description0 15 0 0 0 1 0 1 0 11 A[7:0] A7 A6 A5 A4 A3 A2 A1 A01 B[7:0] B7 B6 B5 B4 B3 B2 B1 B0Set ColumnAddressSet Column start and end addressA[7:0]: Set start column addressfrom 00d-159d [reset= 0d (00h)]B[7:0]: Set end column address from00d-159d [reset= 159d (9Fh)]0 5C 0 1 0 1 1 1 0 00 5D 0 1 0 1 1 1 0 101175A[7:0]B[7:0]0A7B71A6B61A5B51A4B40A3B31A2B20A1B11A0B0Write RAMCommandRead RAMCommandSet RowAddressEnable MCU to write Data into RAMEnable MCU to read Data from RAMSet Row start and end addressA[7:0]: Set start row address from00d-131d [reset= 0d (00h)] B[7:0]:Set end row address from 00d-131d[reset= 131d (83h)]0181A[7:0]1A70A60A50A40A30A20A11A0Set Contrastfor Color "A"Set contrast for all color "A" segment(Pins :SA0 – SA159) A[7:0] validrange: 00d to 255d [reset=128d(80h)]0182A[7:0]1A70A60A50A40A30A21A10A0Set Contrastfor Color "B"Set contrast for all color "B" segment(Pins :SB0 – SB159) A[7:0] validrange: 00d to 255d [reset=128d(80h)]0183A[7:0]1A70A60A50A40A30A21A11A0Set Contrastfor Color "C"Set contrast for all color "C" segment(Pins :SC0 – SC159) A[7:0] validrange: 00d to 255d [reset=128d(80h)]0187A[3:0]1*0*0*0*0A31A21A11A0MasterCurrentControlSet master current attenuation factorA[3:0] can be set from 00d to 15dcorresponding to 1/16, 2/16… to16/16 attenuation. [reset= 15d (0Fh)]BL160128A series - 14 -
Fundamental Command TableD/C# Hex D7 D6 D5 D4 D3 D2 D1 D0 Command Description0 8A 1 0 0 0 1 0 1 01 A[1:0] 0 0 0 0 0 0 A1 A001A0A[7:0]1A70A61A50A40A30A20A10A0Set SecondPre-chargespeedRemap &Color DepthsettingSet Second Pre-charge speedA[1:0]= 00b, Second Pre-chargespeed =slowest A[1:0]= 01b, SecondPre-charge speed =slow A[1:0]=10b, Second Pre-charge speed=normal [reset] A[1:0]= 11b, SecondPre-charge speed =FastSet driver remap and color depthA[0]=0, Horizontal addressincrement [reset] A[0]=1, Verticaladdress increment A[1]=0, RAMColumn 0 to 159 maps to Pin SEG(SA,SB,SC) 0 to 159 [reset] A[1]=1,RAM Column 0 to 159 maps to PinSEG (SA,SB,SC) 159 to 0 A[2]=0,normal order SA,SB,SC (e.g. RGB)[reset] A[2]=1, reverse orderSC,SB,SA (e.g. BGR) A[3]=0,Disable left-right swapping on COM[reset] A[3]=1, Set left-rightswapping on COM A[4]=0, Scanfrom COM0 to COM[N –1] [reset]A[4]=1, Scan from COM[N-1] toCOM0. Where N is the multiplexratio. A[5]=0, Disable COM Split OddEven [reset] A[5]=1, Enable COMSplit Odd Even Refer to Figure10-5 for details. A[7:6] = 00; 256color format A[7:6] = 01; 65k colorformat [RESET] A[7:6] = 10; 256kcolor format A[7:6] = 11; 256kcolor 16-bit format 2 If 9-/18-bit modeis selected, color depth will be fixedto 256k regardless of the setting.Refer to Table 8-7 for details.01A1A[7:0]1A70A61A50A40A30A20A11A0Set DisplayStart LineSet display start line register by RowA[7:0]: from 00d to 131d [reset = 0d(00h)] Note (1) A[7:0] must be set to 0when using A3h command.01A2A[7:0]1A70A61A50A40A30A21A10A0Set DisplayOffsetSet vertical offset by COM A[7:0]:from 00d to 131d [reset = 0d (00h)]0000A4A5A6A711110000111100000000111100110101Set DisplayModeA4h=Normal Display [reset]A5h=Entire Display ON, all pixelsturn ON at GS63 A6h=Entire DisplayOFF, all pixels turn OFFA7h=Inverse DisplayBL160128A series - 15 -
Page 1 and 2: SPECIFICATIONS FORLCD MODULEMODEL N
Page 3 and 4: C O N T E N T S1. Numbering System2
Page 5 and 6: 2. General Specification(1) Mechani
Page 7 and 8: 6. Panel Layout DiagramBL160128A se
Page 9 and 10: 8. Power Supply For LCD Module LCM
Page 11 and 12: 9-2.8080 MPU InterfaceBL160128A ser
Page 13: 10. POWER ON / OFF SEQUENCE & APPLI
Page 17 and 18: Fundamental Command TableD/C# Hex D
Page 19 and 20: Graphic Acceleration Command TableD
Page 21 and 22: Graphic Acceleration Command TableD
Page 23: 13. Appendix ( Drawing )BL160128A s

SPECIFICATIONS FOR LCD MODULE

Create successful ePaper yourself

Delete template?

Save as template?