visakhapatnam steel plant materials management ... - Vizag Steel

More documents

Recommendations

Info

5. Samplers for the collection of hot metal.6. Samplers for the collection of liquid steel.7. Lances for taking the samples.8. 2-wire contact block.9. 4- Wire contact block.10. End connector.11. 4-pin male and female plug.12. Handle.13. 2-core mineral insulated metal sheathed (MIMS) cable.14. 4-core mineral insulated metal sheathed (MIMS) cable.15. 2-core compensating cable.16. 4-core compensating cable.17. Trailing cable.18. All types of lance accessories and consumables.4.0 Maintenance:Regular comprehensive maintenance of the following equipment in allrespects:1. Liquid Metal Temperature measuring instruments -6 Nos.2. Oxygen ppm measuring instruments -7 Nos.3. Hydrogen ppm measuring instruments -1No.4. Large displays for the above measuring systems.5. Signalling circuits along with hooters and lamp compartments for theabove measuring instruments.6. Associated cables upto instrument terminals.7. Calibration instruments such as checkmates.8. Checking the cabling circuit and replacement of the same in case of anytrouble.9. Calibration of the above instruments as per VSP’s QMS (ISO 9001) andpreparation of the calibration certificates.10. Traceability certificates of the secondary master instruments such asdigital multimeters are also to be submitted.11. All lance consumables, required compensating cables, male femaleplugs, instrument cable (If required), laying from field to instrumentincluding its protection shall be considered in the scope of supply.5.0 Operational Requirement:Minimum number of temperature /oxygen/Hydrogen measuring lances to be keptready at different places:TLC1&2- Three (3) Nos Temperature measuring lances per TLCLD Converter 1&2— Three (3) Nos. Temperature& Oxygen ppm measuringlances Per ConverterCCM1, 2 &3- Three (3) Nos Temperature measuring lances per MachineLHF1&2- Three (3) Nos Temperature& Oxygen ppm measuring lances for eachLadle FurnaceARS1&2- Three (3) Nos Temperature& Oxygen ppm measuring lances for eachARSHMDP- Three (3) Nos Temperature measuring lances8
RH Degasser- Three (3) Nos Temperature & Oxygen ppm lances+3 Nos.Hydrogen ppm lances1. To prepare number of lances ready for operations as per daily heat plan ofVSP atleast one day in advance.2. After preparation of lance it is to be checked and calibrated immediately inthe presence of VSP personnel. All the prepared lances are to be provided atrespective locations as and when required.3. Calibration of the checking instrument (Checkmate) is to be done as perVSP quality management system (QMS) and calibration record is to besubmitted to VSP.4. During starting of each shift all lances at TLC1&2, LD Converter1&2, CCM1,2 &3, ARS1&2, LHF1&2, RH Degasser and HMDP are to be checked andcalibrated . A separate register is to be maintained for calibration record ofthe lances.5. Party shall provide adequate and sufficient manpower at different locationssuch as TLC1&2, LD Converter, CCM, LF, ARS, HMDP, RH Degasser etc. forthe maintenance of instruments and lances and for taking the measurementof oxygen ppm, temperature and hydrogen ppm and for the collection ofsamples of hot metal and liquid steel at different locations as specified.6. The party shall submit the printout of the instrument showing the successfulmeasurement of temperature, oxygen ppm and hydrogen ppm. Also theparty shall submit the report showing the successful despatch of sample toLab.7. The party shall undertake sole responsibility for effective operation and costreduction while keeping the quality, stability and safety with the followingguidelines.• Continuous improvement in the performance of probe by monitoring theprobe design.• Use of high quality probe with ZERO downtime on account of probes.• Total supervision and technical support to ensure availability of probes atVSP.• Good training of personnel in taking measurement and sample collection.6.0 Quoting of prices6.1 The party shall quote the rate for each of the below.i. Successful measurement of temperature (cost of all the materials requiredfor each successful measurement of temperature)ii. Successful measurement of oxygen ppm (cost of all the materials requiredfor each successful measurement of oxygen ppm).iii. Successful measurement of hydrogen ppm (cost of all the materialsrequired for each successful measurement of hydrogen ppm).iv. Successful collection of sample of hot metal and liquid steel (cost of all thematerials required for each successful collection of sample).The party shall submit the instrument print out showing the number ofsuccessful measurements of parameters such as temperature, oxygen ppm,hydrogen ppm and collection of samples.9
Page 1 and 2: VISAKHAPATNAM STEEL PLANTMATERIALS
Page 3 and 4: RASHTRIYA ISPAT NIGAM LIMITEDVISAKH
Page 5 and 6: 1.4.4 RINL will inform the technica
Page 7: ANNEXURE-ISpecification for outsour
Page 11 and 12: 9.0 Ownership of the left out mater
Page 13 and 14: ANNEXURE -I BTOTAL QUANTITY FOR 2 Y
Page 15 and 16: oxygen ppm Measurementsystem at LF-
Page 17 and 18: 2.2 In case the Manufacturer wants
Page 19 and 20: 4.4 Illustration for calculation of
Page 21 and 22: (a) District Industries Centre of V
Page 23 and 24: Part-A: Techno Commercial offer for
Page 25 and 26: (ANNEXURE-III TO TENDER NO.PUR.1.41
Page 27 and 28: ANNEXURE-IV TO TENDER NO PUR.1.41.0
Page 29 and 30: We, ...……………… (name of
Page 31 and 32: (ANNEXURE-VII TO TENDER NO.PUR.1.41
Page 33 and 34: 10.0 WAIVER:10.1 Failure to enforce
Page 35 and 36: (ANNEXURE-VIII TO TENDER NO.PUR.1.4
Page 37 and 38: (name of bank & branch)(ANNEXURE- I
Page 39 and 40: Section 3 - Disqualification from t
Page 41 and 42: idders can lodge its complaint / ma
Page 43: Successful measurement oftemperatur

visakhapatnam steel plant materials management ... - Vizag Steel

Create successful ePaper yourself

Delete template?

Save as template?