DAP Deutsches Akkreditierungssystem Prüfwesen GmbH

DAP German Accreditation System for Testing
Shareholder: VMPA, DGZfP, DVS, GL, LGA, VdTÜV
Mr. Dipl.-Ing. K. Görling from Landesmaterialprüfamt
was entrusted as Chief expert.
Appendix to Accreditation Certificate DAP-PL-1191.00
Validity time: 17-05-2002 to 16-05-2012
Certificate for: Martin-Luther-University of
Halle-Wittenberg
Institute of Materials Science
D-06099 Halle
for its
Laboratory
Mechanical Testing of Polymers
MPK Merseburg
Geusaer Straße
D-06217 Merseburg
Tests in the mechanical and fracture mechanical testing
area: of Polymers
Applied see last page
abbreviation:
Mechanical and fracture mechanical Testing of Polymers
ISO 34-1
2004-07
ISO 37
2005-07
ISO 13586
2000-03
ISO 13586 AMD 1
2003-06
Rubber, vulcanized or thermoplastic – Determination of tear
strength
Part 1: Trouser, angle and crescent test pieces
Rubber, vulcanized or thermoplastic – Determination of tensile
stress-strain properties
Plastics – Determination of Fracture Toughness (GIc and KIc) –
Linear Elastic Fracture Mechanics (LEFM) Approach
Plastics – Determination of fracture toughness (GIC and KIC);
Linear elastic fracture mechanics (FEFM) approach –
Amendment 1: Guidelines for the testing of injection-moulded
plastics containing discontinuous reinforcing fibres

ISO /DIS 178
2008
ISO/DIS 179-1
2008
ISO 179-2
1997-12 (including
Technical
Corrigendum 1:
1998-11)
ISO/DIS 527-1
2010-05
ISO/DIS 527-2
2010-05
ISO 527-3
1995-08
ISO 527-4
1997-04
ISO 527-5
2009-10
ISO 604
2002-03
ISO 2039-1
2001-12
ISO 2039-2
1987-07
ISO 6603-1
2000-03
ISO 6603-2
2000-10
Plastics – Determination of Flexural Properties
Plastics – Determination of Charpy impact properties
Part 1: Non-instrumented impact test
Plastics – Determination of Charpy impact properties
Part 2: Instrumented Impact test
Plastics – Determination of tensile properties
Part 1: General Principles
Plastics – Determination of tensile properties
Part 2: Test conditions for moulding and extrusion plastics
Plastics – Determination of tensile properties
Part 3: Test conditions for films and sheets
Corr 1: 1998-06, Corr 2: 2001-04
Plastics – Determination of tensile properties
Part 4: Test conditions for isotropic and orthotropic fibre -
reinforced plastic composites
Plastics – Determination of tensile properties
Part 5: Test conditions for unidirectional fibre-reinforced plastic
composites
Plastics – Determination of compressive properties
Plastics – Determination of hardness
Part 1: Ball indentation method
Plastics – Determination of hardness
Part 2: Rockwell hardness
Plastics – Determination of puncture impact behaviour of rigid
plastics
Part 1: Non-instrumented impact testing
Plastics – Determination of puncture impact behaviour of rigid
plastics
Part 2: Instrumented impact testing

ISO 8256
2004-07
ISO 14125
1998-03
ISO 14125
Corrigendum 1
2003-06
ISO 14130
1997-12
ISO 14130
Technical
Corrigendum 1
2003-11
DIN 53373
1970-09
DIN 53423
1975-11
DIN 53504
2009-10
DIN 65378
1989-11
DIN 65469
1992-08
DVM 001
1986-09
ASTM D 695a
2008
ASTM D 3763
2008
ASTM STP 936
1985-08
Plastics – Determination of tensile-impact strength
Fibre-reinforced plastic composites – Determination of flexural
properties
Fibre-reinforced plastic composites – Determination of flexural
properties
Fibre-reinforced plastic composites – Determination of
apparent interlaminar shear strength by short-beam method
Fibre-reinforced plastic composites – Determination of
apparent interlaminar shear strength by short-beam method
Technical Corrigendum 1
Testing of plastic Films; impact penetration test with electronic
data recording
Testing of rigid cellular materials; flexural test
(zurückgezogen)
Testing of rubber; determination of tensile strength at break,
tensile stress at yield, elongation at break and stress values in
a tensile test
Aerospace; Fibre reinforced plastics; Testing of unidirectional
laminates; Tensile test transverse to fiber direction
Aerospace; Fibre reinforced plastics; Tensile test of monolayer
flat tension specimens
Requirement for the measuring devices for instrumented
Charpy tests
Standard test method for compressive properties of rigid
plastics
Standard test method for high speed puncture properties of
plastics using load and displacement sensors
Instrumented impact testing of plastics and composite
materials

ESIS P2-92
1992
ESIS TC 4
2000
MPK-Procedure
MPK-ICIT
2007-01
MPK-Procedure
MPK-ITIT
2007-02
Applied abbreviations:
Procedure for determining the fracture behaviour of materials
A testing protocol for conducting J-crack growth resistance
curve test on plastics
Testing of plastics – Instrumented Charpy impact test (ICIT)
Procedure for determining the crack resistance behaviour
using the instrumented impact test
Part I: Determination of characteristic fracture mechanics
parameters for resistance against unstable crack propagation
Part II: Determination of characteristic fracture mechanics
parameters for resistance against stable crack propagation
Testing of plastics – Instrumented tensile-impact test
ASTM American Society for Testing and Materials
DVM German Association for Testing Materials
ESIS European Structural lntegrity Society
ISO International Organization for Standardization
MPK-ICIT House Method of Laboratory MPK Merseburg
Instrumented Charpy Impact Test
MPK-ITIT Instrumented Tensile-impact Test
STP Special Technical Publication
For all above listed test areas, authorized to sign test reports are:
Prof. Dr. rer. nat. habil. Wolfgang Grellmann, master of a physics
Dr.-Ing. Christian Bierögel, graduate engineer
further information: http://www.kunststoffdiagnostik.de