easy to use reference charts - Fabco-Air, Inc.

Nonrotating, Twin Rod SeriesBimba Flat-1 cross-over to Fabco-Air Pancake ® IISeries Bore Size Stroke LengthFT- Nonrotating, Double actingTwin Rod04 - 3/4"09 - 1-1/16"17 - 1-1/2"31 - 2"0.125 - 1/8"0.250 - 1/4"0.375 - 3/8"etc.Bimba Flat-1Model NumberCodeF T – 0 9 0.375 – 1 CEBimba Mounting Options FabcoCounterbored mounting holes are standard in the basic modeland need not be specified. For other mounting specify only oneoption code.Bimba Mounting Description Fabco1 - Pivot mount pin in-line with port . . . . . . . . SM1N - Pivot mount pin 90° from port . . . . . . . . . PM2 - Trunnion mount, both ends . . . . . . . . . . . TB2F - Trunnion mount, front 1 . . . . . . . . . . . . . . . TF2R - Trunnion mount, rear 1 . . . . . . . . . . . . . . . TR3 - Threaded mounting holes, both ends . . . HB3F - Threaded mounting holes, front . . . . . . . . HF3R - Threaded mounting holes, rear . . . . . . . . HR4 - Screw clearance holes, both ends . . . . . . CB4F - Screw clearance holes, front . . . . . . . . . . CF4R - Screw clearance holes, rear . . . . . . . . . . CRBimba Model Options FabcoCodes are entered in alphabetical order, except EE which is lastBimba Code Option Description Fabco CodeCE - Counterbored rod end tool bar . . . . . . . . . . . . . . . . . . . . . . . . . . CEG - Magnalube ® G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . StandardK - Rod end tool bar rotated 90° . . . . . . . . . . . . . . . . . . . . . . . . . . . KM, M1, M3, M4 - Magnet on piston; switch mounting post . . . . . . . . . . . . . . . . . . EFor Fabco, specify option “E” and order spacer mountedclamp separately – or – use a Fabco “M” option belowNot available - Magnet on piston with adhesive mounteddovetail extrusion for 1/4" dovetail sensors. . . . . . . . . . . . M, M1, M3, M4P3 - Front port position other than standard . . . . . . . . . . . . . . . . P2, P3, P4Q - Low temperature operation (–40°F to +200°F) . . . . . . . . . . . . . . QS - Stainless steel fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . StandardT1, T3, T4 - Additional switch mounting post located in position 1, 3, or 4For Fabco use spacer mounted clamps – or – “T” option belowNot available - Additional adhesive mounted dovetail extrusionsin position 1, 3, or 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T1, T3, T4V - Viton seals for media compatibility (–15°F to +225°F) . . . . . . . . VY - Moly-coat (MoS 2 I.D. coating) . . . . . . . . . . . . . . . . . . . . . . Not availableEE - Extra rod extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XExampleEE0.375 - 3/8" extra rod extension, etc. . . . . . . . . . . . . . . . . . . . . . . . X0.375, etc.EE1 - 1" extra rod extension, etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . X1, etcPancake ® II Model Number CodeSeries Model Action BoreP N D 3Mounting Stroke– SM 0.375 –OptionsCEModelN - NonrotatingTwin RodSeriesP - Pancake IIActionD - double actingBore2 - 3/4"3 - 1-1/16"4 - 1-1/2"5 -2"Stroke0.125 - 1/8"0.250 - 1/4"0.375 - 3/8"0.500 - 1/2"etc., thru4.000 - 4"4-22 -02

Multi-Power ® SeriesBimba Flat-1 cross-over to Fabco-Air Pancake ® IIFO2FO3FO4Series Bore Size Stroke Length- 2 stage extend, single stage retract- 3 stage extend, single stage retract- 4 stage extend, single stage retract50 - 2-1/2"70 - 3"125 - 4"0.125 - 1/8"0.250 - 1/4"0.375 - 3/8"etc.Bimba Flat-1Model NumberCodeFO3 – 50 0.750 – 3 MBimba Mounting Options FabcoBimba Mounting Description Fabco3 - Threaded mounting holes, both ends . . . . HB3F - Threaded mounting holes, front . . . . . . . . HF3R - Threaded mounting holes, rear . . . . . . . . . HR4 - Screw clearance holes, both ends . . . . . . CB4F - Screw clearance holes, front . . . . . . . . . . . CF4R - Screw clearance holes, rear . . . . . . . . . . . CRBimba Model Options FabcoCodes are entered in alphabetical order, except EE which is lastBimba Code Option Description Fabco CodeCFT - Coarse female rod thread, dimension E . . . . . . . . . . . . . . . . . . TCFCMT - Male rod end with coarse thread . . . . . . . . . . . . . . . . . . . . . . . TCMG - Magnalube ® G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . StandardL - Low friction seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LM, M1, M3, M4 - Magnet on piston; switch mounting post . . . . . . . . . . . . . . . . . . EFor Fabco, specify option “E” and order spacer mountedclamp separately – or – use a Fabco “M” option belowNot available - Magnet on piston with adhesive mounteddovetail extrusion for 1/4" dovetail sensors. . . . . . . . . . . . M, M1, M3, M4MT - Male rod end, fine thread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TFMNT - Non-threaded rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TNP2, P3, P4 - Front port position other than standard . . . . . . . . . . . . . . . . P2, P3, P4P6, P7, P8 - Rear port position other than standard . . . . . . . . . . . . . . . . . P6, P7, P8Q - Low temperature operation (–40°F to +200°F) . . . . . . . . . . . . . . QT1, T3, T4 - Additional switch mounting post located in position 1, 3, or 4For Fabco use spacer mounted clamps – or – “T” option belowNot available - Additional adhesive mounted dovetail extrusionsin position 1, 3, or 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T1, T3, T4V - Viton seals for media compatibility (–15°F to +225°F) . . . . . . . . VW - Rod wiper, Buna N only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WY - Moly-coat (MoS 2 I.D. coating) . . . . . . . . . . . . . . . . . . . . . . Not availableEE - Extra rod extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XExampleEE0.375 - 3/8" extra rod extension, etc. . . . . . . . . . . . . . . . . . . . . . . . X0.375, etc.EE1 - 1" extra rod extension, etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . X1, etcPancake ® II Model Number CodeSeries Model Action BoreP M 3 6Mounting Stroke– HB 0.75 –OptionsE or MModel and ActionM2 - 2-stage extend, one retractM3 - 3-stage extend, one retractM4 - 4-stage extend, one retractSeriesP - Pancake IIBore6 - 2-1/2"7 -3"8 -4"Stroke0.125 - 1/8"0.250 - 1/4"0.375 - 3/8"0.500 - 1/2"etc., thru4.000 - 4"4-22-02

Bimba Flat-1 Model Number CodeMulti-Position SeriesBimba Flat-1 cross-over to Fabco-Air Pancake ® IISeriesFOPDouble acting,multiple position,single rod02 - 1/2"04 - 3/4"09 - 1-1/16"17 - 1-1/2"Bore Size31 - 2"50 - 2-1/2"70 - 3"125 - 4"Stroke Length A0.250 - 1/4"0.375 - 3/8"0.500 - 1/2"etc.Stroke Length B0.250 - 1/4"0.375 - 3/8"0.500 - 1/2"etc.Bimba Flat-1Model NumberCodeFOP – 31 0.375 / 1.500 – 3 VBimba Mounting Options FabcoCounterbored mounting holes are standard in the basicmodel and need not be specified. For other mounting specifyonly one option code.Bimba Mounting Description Fabco1 - Pivot mount pin in-line with port . . . . . . . . SM1N - Pivot mount pin 90° from port . . . . . . . . . . PM3 - Threaded mounting holes, both ends . . . . HB3F - Threaded mounting holes, front . . . . . . . . HF3R - Threaded mounting holes, rear . . . . . . . . . HR4 - Screw clearance holes, both ends . . . . . . CB4F - Screw clearance holes, front . . . . . . . . . . . CF4R - Screw clearance holes, rear . . . . . . . . . . . CRBimba Model Options FabcoCodes are entered in alphabetical order, except EE which is lastBimba Code Option Description Fabco CodeCFT - Coarse female rod thread, dimension E . . . . . . . . . . . . . . . . . . TCFCMT - Male rod end with coarse thread . . . . . . . . . . . . . . . . . . . . . . . TCMG - Magnalube ® G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . StandardL - Low friction seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LM, M1, M3, M4 - Magnet on piston; switch mounting post . . . . . . . . . . . . . . . . . . EFor Fabco, specify option “E” and order spacer mountedclamp separately – or – use a Fabco “M” option belowNot available - Magnet on piston with adhesive mounteddovetail extrusion for 1/4" dovetail sensors. . . . . . . . . . . . M, M1, M3, M4MT - Male rod end, fine thread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TFMNT - Non-threaded rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TNP2, P3, P4 - Front port position other than standard . . . . . . . . . . . . . . . . P2, P3, P4P6, P7, P8 - Rear port position other than standard . . . . . . . . . . . . . . . . . P6, P7, P8Q - Low temperature operation (–40°F to +200°F) . . . . . . . . . . . . . . QS - Stainless steel fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . StandardT1, T3, T4 - Additional switch mounting post located in position 1, 3, or 4For Fabco use spacer mounted clamps – or – “T” option belowNot available - Additional adhesive mounted dovetail extrusionsin position 1, 3, or 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T1, T3, T4V - Viton seals for media compatibility (–15°F to +225°F) . . . . . . . . VW - Rod wiper, Buna N only (page 8) . . . . . . . . . . . . . . . . . . . . . . . . WY - Moly-coat (MoS 2 I.D. coating) . . . . . . . . . . . . . . . . . . . . . . Not availableEE - Extra rod extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XExampleEE0.375 - 3/8" extra rod extension, etc. . . . . . . . . . . . . . . . . . . . . . . . X0.375, etc.EE1 - 1" extra rod extension, etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . X1, etcPancake ® II Model Number CodeSeries Model Action BoreP 3 D 4Mounting Stroke A / Sroke B– SM 0.375 / 1.500 –OptionsVModel and Action3D - 3-position, double actingSeriesP - Pancake IIBore1 - 1/2"2 - 3/4"3 - 1-1/16"4 - 1-1/2"5 -2"6 - 2-1/2"7 -3"8 -4"Stroke A0.125 - 1/8"0.250 - 1/4"0.375 - 3/8"0.500 - 1/2"etc., thru4.000 - 4"Stroke B0.125 - 1/8"0.250 - 1/4"0.375 - 3/8"0.500 - 1/2"etc., thru4.000 - 4"4-22-02