END MILLS - Fastcut Tool

Serving the Metal-Cutting Industry for Five Decades.DOUBLE END TWO FLUTE BALL - STUB LENGTH(Former List Number 2003 and New Sizes)◆◆◆◆◆Most Ferrous, Non-Ferrous andNon-Metallic MaterialsPlunge and RampProfile, Slot and PocketMicrograin Solid Carbide30° Right Hand Helix, Right Hand CutSOLID CARBIDE◆ Center Cutting◆ Plain Round Shank◆ High Rigidity from Substrate◆ Optimum Speeds and Feeds◆ Cutting Diameter Tolerance is:Sizes less than 1/8, +.000/-.001Sizes 1/8 through 1/4, +.000/-.002Sizes larger than 1/4, +.000/-.003Cutter Shank Length Overall EDP No.Dia. Dia. of Cut Length Uncoated TiCN1/32 1/8 3/32 1-1/2 94969 949713/64 1/8 3/32 1-1/2 94972 949741/16 1/8 1/8 1-1/2 94900 949475/64 1/8 1/8 1-1/2 94975 949773/32 1/8 3/16 1-1/2 94902 949487/64 1/8 1/4 1-1/2 94978 949801/8 1/8 1/4 1-1/2 94904 949499/64 3/16 5/16 2 94981 949835/32 3/16 5/16 2 94906 9495011/64 3/16 3/8 2 94984 949863/16 3/16 3/8 2 94908 949517/32 1/4 1/2 2-1/2 94910 949521/4 1/4 1/2 2-1/2 94912 949535/16 5/16 1/2 2-1/2 94914 949543/8 3/8 9/16 2-1/2 94916 949557/16 7/16 5/8 3 94918 949561/2 1/2 5/8 3 94920 949575/8 5/8 3/4 4 94987 949893/4 3/4 1 4 94990 94992Solid Carbide Two Flute End MillsDOUBLE END TWO FLUTE BALL(Former List Number 2004)◆ Most Ferrous, Non-Ferrous andNon-Metallic Materials◆ Plunge and Ramp◆ Profile, Slot and Pocket◆ Micrograin Solid Carbide◆ 30° Right Hand Helix, Right Hand Cut◆ Center Cutting◆ Weldon Shank◆ High Rigidity from Substrate◆ Optimum Speeds and Feeds◆ Cutting Diameter Tolerance is:Sizes 1/8 through 1/4, +.000/-.002Sizes larger than 1/4, +.000/-.003Cutter Shank Length Overall EDP No.Dia. Dia. of Cut Length Uncoated TiCN1/8 3/8 3/8 3-1/8 94700 947445/32 3/8 7/16 3-1/4 94702 947453/16 3/8 1/2 3-1/4 94704 947467/32 3/8 9/16 3-1/2 94706 947471/4 3/8 5/8 3-1/2 94708 947489/32 3/8 11/16 3-1/2 94710 947495/16 3/8 3/4 3-1/2 94712 9475011/32 3/8 3/4 3-1/2 94714 947513/8 3/8 3/4 3-1/2 94716 947527/16 1/2 7/8 4 94718 947531/2 1/2 1 4 94720 9475412