FTB-8120NGE/8130NGE Power Blazer - Advanced Test Equipment ...

More documents

Recommendations

Info

FTB-8120NGE/8130NGE Power BlazerEthErnEt functional SPEcificationS (cont’d)TESTING (10 GIGE)EtherSAM (Y.1564)Capability to perform the service configuration test, including the ramp and burst tests and service performance test as per ITU-T Y.1564.Tests can be performed to a loopback or dual test set mode for bidirectional results.RFC 2544 Throughput, back-to-back, frame loss and latency measurements according to RFC 2544.Frame size: RFC-defined sizes, user-configurable.BERTUnframed, framed layer 1, framed layer 2 supported with or without VLAN Q-in-Q.Patterns (BERT)PRBS 2E9-1, PRBS 2E11-1, PRBS 2E15-1, PRBS 2E20-1, PRBS 2E23-1, PRBS 2E31-1, and up to 10 user patterns.Error insertion (BERT) FCS, bit, 64B/66B BlockError measurementLAN/WAN: jabber/giant, runt, undersize, oversize, FCS, 64B/66B BlockWAN: B1, B2, B3, REI-L, REI-PUDP, TCP and IP header checksumError measurement (BERT)Alarm insertionAlarm detectionService disruption time (SDT)measurement (BERT)VLAN stackingFlow-control statisticsBit error, bit mismatch 0, bit mismatch 1, performance monitoring (G.821 and G.826)LOS, link down, local fault, remote fault, pattern loss (BERT)WAN: SEF, LOF, AIS-L, RDI-L, AIS-P, RDI-P, LCD-P, LOP-P, ERDI-PSD, ERDI-PCD, ERDI-PPD, UNEQ-PLOS, link down, local fault, remote fault, frequency offset, pattern loss (BERT)WAN: SEF, LOF, AIS-L, RDI-L, AIS-P, RDI-P, LCD-P, LOP-P, ERDI-PSD, ERDI-PCD, ERDI-PPD, PLM-P, UNEQ-P, link (WIS)Defect or No Traffic mode. Disruption time statistics include shortest, longest, last, average, total and count.Capability to generate one stream with up to three layers of VLAN (including IEEE802.1ad Q-in-Q tagged VLAN).Pause time, last pause time, max. pause time, min. pause time, paused frames, abort frames, frames Tx, frames Rx.Multistream generation Capability to transmit up to 10 streams. Configuration parameters are packet size, transmission mode (N-Frames, Burst, N-Burst, Ramp, N-Ramp and Continuous),MAC source/destination address, VLAN ID, VLAN priority, IP source/destination address, ToS field, DSCP field, TTL, UDP source/destination port and payload.(Available with Frame-Analyzer software option.) Selectable predefined stream profiles are also available for VoIP, video and data streams.VoIP codecs (G.711, G.723.1, G.729), video (MPEG-2 SDTV, MPEG-2 HDTV, MPEG-4 HDTV).Traffic filteringCapability to analyze the incoming traffic and provide statistics according to a set of up to 10 configurable filters. Filters can be configured for MAC source/destination address, VLAN ID, VLAN priority, IP source/destination address, ToS field, DSCP field, TCP source/destination port and UDP source/destination port.VLAN filtering can be applied to any of the stacked VLAN layers. (Available with Frame-Analyzer software option.)Multistream analysisCapability to analyze per stream statistics: packet jitter, latency, throughput, frame loss and out-of-sequence (available with Frame-Analyzer software option)Ethernet statisticsMulticast, broadcast, unicast, N-unicast, pause frame, frame size distribution, bandwidth, utilization, frame rate, frame loss, out-of-sequence framesand in-sequence frames. (Available with Frame-Analyzer software option.)Packet jitter statisticsDelay variation statistics (ms)—min., max., last, average and jitter measurement estimate (RFC 3393) (available with Frame-Analyzer option).PBB-TE aCapability to generate and analyze streams with PBB-TE data traffic including configuration of B-MAC (source and destination), B-VLAN and I-tag(as per 802.1ah) and to filter received traffic by any of these fields.MPLS aCapability to generate and analyze streams with up to two layers of MPLS labels and to filter received traffic by MPLS label or COS.IPv6 aCapability to perform BERT, RFC 2544, traffic generation and analysis and Smart Loopback tests over IPv6; ping, traceroute, neighbor discovery and statelessauto-configuration.Advanced filtering aCapability to enhance the filters with up to four (4) fields each, which can be combined with AND/OR/NOT operations.A mask is also provided for each field value to allow for wildcards. Complete statistics are gathered for each defined filter.Data capture aCapability to perform 10/100/1000M full-line-rate data capture and decode.Capability to configure detailed capture filters and triggers as well as capture slicing parameters.One-way delay Capability to measure one-way frame delay as part of EtherSAM (Y.1564) and RFC 2544ADDITIONAL TEST AND MESUREMENT FUNCTIONS (10 GIGE)Power measurementFrequency generationand measurementSignal label controland monitoringDual test setDHCP clientSmart LoopbackIP toolsSupports optical power measurement, displayed in dBm.Supports clock frequency generation and measurements (i.e., received frequency and deviation of the input signal clock from nominal frequency).Frequency offset generation:Range: ±50 ppmResolution: ±1 ppmUncertainty (accuracy): ±4.6 ppmFrequency offset measurement:Range: ±135 ppmResolution: ±1 ppmUncertainty (accuracy): ±4.6 ppmAbility to configure and monitor J0 Trace, J1 Trace and payload signal label C2 (WAN).Performs end-to-end, bidirectional performance testing (as required by leading standards bodies)—remote FTB-8120NGE/8130NGE controlled via the LANconnection under test.Capability to connect to a DHCP server to obtain its IP address and subnet mask to connect to the network.Capability to return traffic to the local unit by swapping packet overhead up to layer 4 of the OSI stack.Capability to perform ping and traceroute functions.Notea. Available as a software option.
EthErnEt functional SPEcificationS (cont’d)ADDITIONAL FEATURESExpert modefiBrE channEl intErfacESAbility to set thresholds in RFC 2544 and BERT mode to provide a pass/fail status.FTB-8120NGE/8130NGE Power BlazerScriptingThe built-in Visual Basic .NET scripting engine and embedded macrorecorder provide a simple means of automating test cases and routines.Embedded scripting routines provide a powerful means of creating advanced test scripts. aEvent loggerSupports logging of test results, and the ability to print, export (to a file), or export the information contained in the logging tool.Power up and restore aIn the event of a power failure to the unit, the active test configuration and results are saved and restored upon bootup.Save and load configurationAbility to store and load test configurations to/from non-volatile memory.Configurable test viewsAllows users to customize their test views; i.e., to dynamically insert or remove test tabs/windows, in addition to creating new test windows,so as to accurately match their testing needs. aConfigurable test timerAllows a user to set a specific start, stop and duration for tests.Test favoritesCapability to select and load from predefined or user-modified test conditions.Report generationAbility to generate test reports in the following user-selectable formats: .pdf, .html, .txt and .csv.Graph Allows to graphically display the test statistics of the performance (RFC 2544).Screen capturing bCapability to gather a snap-shot of the screen for future use.Logger printing bCapability to send logger messages to a supported local printer.Remote controlRemote control through Visual Guardian Lite software or VNC.FC-1X/2X/4XWavelength (nm) 850 1310 1310 1550Tx level (dBm) –9 to –2.5 –8.4 to –3 0 to 5 1 to 5Rx level sensitivity (dBm)–15 at FC-4–18 at FC-2–20 at FC-1–18 at FC-4–21 at FC-2–22 at FC-1–18 at FC-4–21 at FC-2–22 at FC-1–16.5 at FC-4–20.5 at FC-2–22 at FC-1Maximum reach500 m on 50/125 µm MMF c 4 km 30 km 40 km300 m on 62.5/125 µm MMF cTransmission bit rate (Gbit/s) 1.06/2.125/4.25 1.06/2.125/4.25 1.06/2.125/4.25 1.06/2.125/4.25Reception bit rate (Gbit/s) 1.06/2.125/4.25 1.06/2.125/4.25 1.06/2.125/4.25 1.06/2.125/4.25Tx operational wavelength range (nm) 830 to 860 1260 to 1350 1285 to 1345 1544.5 to 1557.5Measurement uncertainty (accuracy)Frequency (ppm)Optical power (dB)±4.6±2Notesa. Available on the FTB-500 platform only.b. Available on the FTB-200 platform only.c. Values in the table correspond to FC-1 rate. For FC-2, maximum reach is 300 m on 50/125 µm MMF and 150 m on62.5/125 µm MMF. For FC-4, maximum reach is 150 m on 50/125 µm MMF and 70 m on 62.5/125 µm MMF.±4.6±2Max Rx before damage (dBm) 3 3 3 3Jitter compliance ANSI FC-PI-2 ANSI FC-PI-2 ANSI FC-PI-2 ANSI FC-PI-2FC classification ANSI FC-PI-2 ANSI FC-PI-2 ANSI FC-PI-2 ANSI FC-PI-2Laser type VCSEL Fabry-Perot DFB DFBEye safety Class 1 Class 1 Class 1 Class 1Connector LC LC LC LCTransceiver type SFP SFP SFP SFPFC-10XWavelength (nm) 850 1310 1310 1550 1550Tx level (dBm) –5 to –1 0.5 max –6 to –1 –1 to 2 0 to 4Rx level sensitivity (dBm) –11.1 –12.6 –14.4 –16 –23Maximum reach300 m on 50/125 µm MMF 10 km 10 km 40 km 80 km30 m on 62.5/125 µm MMFTransmission bit rate (Gbit/s) 10.5 10.5 10.5 10.5 10.5Reception bit rate (Gbit/s) 10.5 10.5 10.5 10.5 10.5Tx operational wavelength range (nm) 840 to 860 1260 to 1355 1290 to 1330 1530 to 1565 1530 to 1565Measurement uncertainty (accuracy)Frequency (ppm)Optical power (dB)±4.6±2±4.6±2Max Rx before damage (dBm) 6 6 6 2 4Jitter compliance ANSI FC-PI-3 ANSI FC-PI-3 ANSI FC-PI-3 ANSI FC-PI-3 ANSI FC-PI-3FC classification ANSI FC-PI-3 ANSI FC-PI-3 ANSI FC-PI-3 ANSI FC-PI-3 ANSI FC-PI-3Laser type VCSEL DFB DFB EML EMLEye safety Class 1 Class 1 Class 1 Class 1 Class 1Connector LC LC LC LC LCTransceiver type XFP XFP XFP XFP XFP±4.6±2±4.6±2±4.6±2±4.6±2±4.6±2
Page 1 and 2: ®Established 1981Advanced Test Equ
Page 3: thE choicE for intEgratEd MultiSErv
Page 6 and 7: ETHERSaM: thE nEW Standard in EthEr
Page 8 and 9: Ethernet Quality of Service Measure
Page 10 and 11: FTB-8120NGE/8130NGE Power BlazerunS
Page 12 and 13: ElEctrical intErfacESThe following
Page 14 and 15: FTB-8120NGE/8130NGE Power BlazerSon
Page 16 and 17: SonEt/Sdh functional SPEcificationS
Page 18 and 19: FTB-8120NGE/8130NGE Power BlazerEth
Page 22 and 23: FTB-8120NGE/8130NGE Power BlazerfiB
Page 24: FTB-8120NGE/8130NGE Power BlazerEXF

FTB-8120NGE/8130NGE Power Blazer - Advanced Test Equipment ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?