4" Super Angle Filter - Netafim
4" Super Angle Filter - Netafim
4" Super Angle Filter - Netafim
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
4" <strong>Super</strong> <strong>Angle</strong> <strong>Filter</strong>Technical DataInlet/outlet diameter 110mm/ 4”End connections (optional)Maximum pressureMaximum flow rateFiltration areaFiltration volume<strong>Filter</strong> length<strong>Filter</strong> widthDistance between end connectionsDistance between end connectionsLength of filter elementWeight (victaulic connection)Weight with ARKAL flangesMaximum temperature4" Victaulic .4" ARKAL FLANGE10 bar 145 psi90 m 3 /h 396 gpm1852 cm 2 287 in 21744 cm 3 108 in 3700 mm 27 9 / 16"410 mm 15 3 /4"187 mm 7 9 / 32"147 mm 5 23 / 32"347 mm 13 21 / 32"10.6kg 23.32 lbskg 31.02 lbs60° C 140° F147 [5 25/32"]IN187 [7 3/8"]410 [16 5/32"]OUT664 [26 5/32"]147 [5 25/32"]IN187 [7 3/8"]410 [16 5/32"]OUT664 [26 5/32"]Filtration GradesHead Loss ChartOff-white (800 micron / 18 mesh)Blue (400 micron / 40 mesh)Yellow (200 micron / 80 mesh)44 100FLOW RATE200 440 GPMRedBlackGreenGrey(130 micron / 120 mesh)(100 micron / 140 mesh)(55 micron)(20 micron)HEAD LOSS (kg/cm )21.00.80.60.40.320 30 40 60805 10 20 303100 m / hl / s14.2210.005.000.23.0020 micron55 micron0.10100 micron130 micron0.08200-800 micron 1.000.060.05 0.7110HEAD LOSS (PSI)AK 4” SUPER ANGLE 9606 71410EN 11/07
Dismantling (for cleaning)1. Make sure that the water inlet is turned off and pressure is released.2. Drain the filter through the drainage valve.3. Open the cover by pulling the safety pin out and lifting the clamp lever.4. Remove the filter cover with a slight anticlockwise rotation.5. Remove the filter element.6. Release the spine tightening nut.7. Pull the cap's telescopic extension to decompress the discs.8. Rinse using a high-pressure water jet.Assembly1. Close the spine tightening nut until the discs are tightly compressed.2. Position the filter element back in place.3. Place the filter cover on the filter body and secure it with a slight clockwise rotation.4. Secure the clamp onto the cover and close using the lever, insert the safety pin.Installation1. The 4" SUPER ANGLE filter may be installed horizontally or vertically.2. A shut off valve should be installed at the filter inlet in order to close water supply for servicing.3. A small tap with a flexible hose should be connected in front of the shut off valve for manual cleaning of the filter element.CommentsFlange: Bolt length – recommended ” 10-10mm. Use standard washers.Part ListNo. Description Materials1 <strong>Filter</strong> cover PP2 Hydraulic seal EPDM13 Clamp S.S4 3"-4" Spine tightening nut R.PP5 3"-4" Spine cap R.PP236 Disc set PP7 O-ring 2-220 EPDM8 3"-4" Spine 99 R.PP459 ½” x ¼” Tap BRASS10 3"-4" <strong>Filter</strong> element3"-4" Spine (without disc set)671011 4” body complex victaulic ends11.1 4” body complex flange ends12 4" AK Flange12.1 Loose flange R.P.A12.2 Cone flange POM12.3 4" Gasket style 90 EPDMMaterialsR.PP. - Reinforced PolypropyleneR.PA. - Reinforced PolyamideS.S. - Stainless SteelPP - PolypropylenePOM- Polyacetal811.1AK 4” SUPER ANGLE 9606 71410EN 11/07
Change language