DP2 SERIE PRINCE 300/500/700/1000W - QuickÂ® SpA

More documents

Recommendations

Info

GBMAINTENANCE41 Stud 8*060 Ø8 MBP080608X0042 Gearbox flange gasket TOP TG40 PGFLRDTG400043A Gearbox - Quick TG40 500W SLMR05TG400043B Gearbox - Quick TG40 500W HS SLMR05TG40HS44 Washer MBR08X00000045 Grower MBR08XDE000046 Nut MBD08MXEN00047 Screw MBV0516MXE0048 Geared motor seal PGBMR040000049 Key MBH040415F0050A Electric motor 300W 12V EMF03120000050B Electric motor 500W 12V EMF05120000050C Electric motor 500W 24V EMF05240000051 Flange gasket PGGPMFN0400052 Motor casing watertight 300/500W PCCCPM04000053 Poles gasket electric motor PGGPMPM0400054 Bottom protec cover electric motor PCCPPMFN040055 Screw MBV03916AXCC56 Stud 8*080 Ø8 MBP080808X0057 Gearbox flange gasket TOP TG50 PGFLRDTG5000058 Gearbox - Quick TG50 1000W SLMR10TG500059 Washer MBR061815X0060 Self locking nut MBD06MXET00061 O-ring PGR02300000062 Key MBH050515F0063A Electric motor 700w 12v EMF07120000063B Electric motor 1000w 12v EMF10120000063C Electric motor 700w 24v EMF07240000063D Electric motor 1000w 24v EMF10240000064A Motor casing watertight 700w PCCCPM07000064B Motor casing watertight 1000w PCCCPM10000065 Grommet 700/1000w PCGPMMR0000066 Terminal board cover 700/1000w PCCPPMMR000067 Screw MBV02213AXSC68 Bottom gasket 700/1000w PGGPMFN0000069 Bottom protec cover 700/1000w PCCPPMFN000070 Cable outlet PPM20B000000414950424854554344454653475251MOTORGEARBOX 300/500W566357626869 67584445466167705960646665MOTORGEARBOX 700/1000W20DP2 300/500/700/1000W - REV001A
WARNING - USAGEGBWARNINGWARNING: stay clear of the chains, ropes and gypsy. Make sure the electric motor is off when windlass is used manually(even when using the handle to disengage the clutch). In fact people with windlass remote controls (hand-held remotecontrol or radio-controlled systems) might accidentally operate it.WARNING: secure the chain with a device before starting the navigation.WARNING: do not operate the windlass by using the electrical power when the handle is inserted in the drum or intothe gypsy cover.WARNING: Quick ® recommends using a protection to prevent the engine line from suffering damages due to overheatingor shortcircuits. For AC currents the use of a fuse is recommended (details on its dimension are specified in the pageof the connection diagram); For DC currents the use of a specific and delayed-action (thermal-magnetic or hydraulicmagnetic)circuit breaker is recommended. The circuit breaker can be used to cut off power to the windlass controlcircuit and so avoid accidental activation.CLUTCH USEThe clutch (6 and 8) provides a link between the gypsy (7) and the main shaft (16, 17, 18 or 19). The clutch can be released (disengagement)by using the handle (1 or 2) which, when inserted in the bush (3) of the drum (4) or into the gypsy cover (5), mustbe turned counter-clockwise. The clutch will be re-engaged by turning it clockwise (engagement).WEIGHING THE ANCHORTurn on the engine. Make sure the clutch is engaged and remove the handle (1 or 2).Press the UP button on the control provided.If the windlass stops and the hydraulic magnetic switch (or thermal cutout) has not tripped, wait a few seconds and try again(avoid keeping the button pressed).If the hydraulic magnetic switch, has tripped, reset it and wait a few minutes before weighing anchor once again.If, after a number of attempts, the windlass is still blocked, we suggest to move the boat to release the anchor.Check the upward movement of the chain for the last few meters in order to avoid damages to the bow.CASTING THE ANCHORThe anchor can be cast by using the electrical control or manually. To operate manually, the clutch (6 and 8) must be disengagedallowing the gypsy (7) to revolve and letting the rope or chain fall into the water.To slow down the chain, the handle (1 or 2) must be turned clockwise.To cast the anchor by using the electrical power, press the DOWN button on the control provided. In this manner, anchor castingis under control and the chain and rope unwind evenly.In order to avoid any stress on the windlass -once the boat is anchored- fasten the chain or secure it in place with a rope.DP2 300/500/700/1000W - REV001A21
Page 8 and 9: 8 DP2 300/500/700/1000W - REV001AIT
Page 10 and 11: ITMANUTENZIONE41 Prigioniero 8*060
Page 12 and 13: ITSETBARBOTIN - DP2OSP BARBOTIN DP2
Page 14 and 15: GBTECHNICAL DATAHOW TO IDENTIFY THE
Page 16 and 17: GBCONNECTION DIAGRAMBASIC SYSTEM DP
Page 18 and 19: 18GBDP2 300/500/700/1000W - REV001A
Page 22 and 23: GBSETGYPSY - DP2OSP GYPSY DP2 1/4
Page 24 and 25: RADIO RECEIVER RRCMOD. R02 (2CH)UPD
Page 26 and 27: DP2 - DIMENSIONI / DIMENSIONS mm (i
Page 28: DP2 SERIE PRINCE300/500/700/1000WR0

DP2 SERIE PRINCE 300/500/700/1000W - QuickÂ® SpA

Create successful ePaper yourself

Delete template?

Save as template?