You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
320V<strong>AQUAMAX</strong> <strong>BASECOAT</strong> series 500WATERBORNE <strong>BASECOAT</strong> FOR 2-3 STAGE FINISHESAquaMax Basecoat is a waterborne basecoat for multistage and pearl effect colours.This product has excellent hiding power that delivers high quality and productivity.Can be used in full panel & spot repair situations.AquaMax Basecoat can be recoated with any clearcoat of MaxMeyer Car Refinish range,with highest result and durability.AquaMax Basecoat is not flammable and strongly reduces solvent emission to theatmosphere.SUBSTRATESMaxMeyer Compliant 2K HS Primers and Fillers(Refer to product TDS for compatibility with Aquamax Basecoat)Original finishes, sanded (P360 - 400 or scotch brite fine)PREPARATIONSee the technical data sheet of the undercoat used. Final sanding with P320-400 andScotch Brite Fine (hand or machine) is strongly recommended before topcoating.In spot repair thoroughly sand fillers with P800-2000 for better covering of scratches.Tack with tag-rag before topcoating.<strong>AQUAMAX</strong> <strong>BASECOAT</strong>TAP WATERPOT LIFEVOLUME1000100 - 300100 - SCB and pearlescent colours200 - metallic colours300 - metallic at temperature >25-30°C.3 months. Stir well before use.Viscosity will vary with thinner level chosen, but optimum optimum application viscosity is22 – 26 seconds DIN4 at 20°C.THINNERTap waterJanuary 2007These products are for professional use only.
320VAPPLICATIONGun setups Conventional HVLPLVLP orhigh transferefficiency> 65 %Gravity spray gun nozzle (mm) 1.2-1.3 1.2-1.3 1.2-1.3Pressure at the gun (bar) 2-3 0.3-0.7 2-3Number of coats: 2-3 2-3Suggested thickness:15-20 micronsImportant:If necessary apply a final crossed mist-coat in order to get a uniform metallic control.Thoroughly clean spray equipment with tap water or Gun Cleaner before use.Do not use spray equipment containing residues of solvent. After use thoroughlyclean spray equipment withtap water or Gun Cleaner.DRYINGAIR DRYING ( 20°C, less than 50% humidity)Flash off between coatsFlash off between coats (air blower)Flash off before application of clearAIR DRYINGI.R. DRYINGMedium wavesShort waves10-15 minutes1-2 minutes20-30 minutes3 minutes2 minutesImportant:Dry AquaMax Basecoat until the film becomes matt before using the IR lamp.CLEARSAll 2K clearcoats in MaxMeyer Car Refinish range excluding UHS Clear 0260.TECHNICAL DATAPack size 0.5 - 1 l.StorageStore in a cool dry place away from heatTheoretical coverage 12.5-20 sqm/l. of ready for use product, 10 microns thicknessVOC INFORMATIONThe EU limit for this product (product category:IIB.d) in ready for use form is max. 420g/lof VOC. The VOC content of this product in ready for use form is max. 420 g/l.Depending on the chosen mode of use, the actual ready to use VOC of this productmay be lower than that specified by the EU Directive code.SAFETY AND HANDLINGThese products are for professional use onlyand are not to be used for purposes other than those specified.The information on this TDS is based on present scientific andtechnical knowledge, and it is the responsibility of theuser to take all necessary steps in order to ensure thesuitability of the product for the intended purpose.For further information please contact:PPG Industries (UK) Limited.MaxMeyer DivisionCustomer Service & Sales Group,Needham Road,Stowmarket,Suffolk.IP14 2AD,England.For Health and Safety information, please refer to thematerial Safety Data Sheet, also available at : Tel: 01449 771779http://www.ppg.com/Maxmeyer_MSDS Fax: 01449 773495MaxMeyer and the MaxMeyer logo© 2007 PPG Industries. All rights reserved.are trademarks of PPG Industries.
Change language