产品规格书 SPECIFICATION - 无锡市好达电子有限公司

规 格 书 编 号SPEC NO :产 品 规 格 书SPECIFICATIONCUSTOMER 客 户 :PRODUCT 产 品 :MODEL NO 型 号 :MARKING 印 字 :SAW FILTERHDF110L S3HDF112PREPARED 编 制 : CHECKED 审 核 :APPROVED 批 准 : D A T E 日 期 : 2006-5-11客 户 确 认 CUSTOMER RECEIVED:审 核 CHECKED 批 准 APPROVED 日 期 DATE无 锡 市 好 达 电 子 有 限 公 司Shoulder Electronics Limitedwww.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 1 of 8

SAW FILTERHDF110L S3更 改 历 史 记 录History Record更 改 日 期Date规 格 书 编 号Spec. No.产 品 型 号Part No.客 户 产 品 型 号Customer No.更 改 内 容 描 述Modify Content备 注Remarkwww.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 2 of 8

SAW FILTERHDF110L S31. SCOPEThis specification shall cover the characteristics of SAW filter F110L.2. ELECTRICAL SPECIFICATIONDC Voltage VDC10VAC Voltage Vpp10V50Hz/60HzOperation temperature -40℃ to +85℃Storage temperature -45℃ to +85℃RF Power Dissipation0dBm2.2Electronic Characteristics型 号Part Number中 心 频 率 (fo)(MHz)Nominal Center Frequency3dB 带 宽Bandwidth(from fo)(KHz)阻 带 衰 耗Stop Band Attenuation(from peak level)(dB)1)fo-3×1.728MHz2)fo-2×1.728MHz3)fo+/-1.728MHz4)fo+2×1.728MHz5)fo+3×1.728MHz插 入 损 耗 (dB)Insertion Loss(at minimum loss point)群 延 时 波 动 (fo+/-576KHz)(μsce.)Group Delay Deviation输 入 / 输 出 阻 抗Input/output ImpedanceHDF110L110+/-576min50min45min30min40min40min4.5max0.7300Ω//1.2μHwww.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 3 of 8

SAW FILTERHDF110L S34.TESTCIRCUIT5. ENVIRONMENTAL CHARACTERISTICS5-1 High temperature exposureSubject the device to +85℃ for 16 hours. Then release the filter into the room conditionsfor 24 hours prior to the measurement. It shall fulfill the specifications in 2.2.5-2 Low temperature exposureSubject the device to -40℃ for 16 hours. Then release the device into the room conditionsfor 24 hours prior to the measurement. It shall fulfill the specifications in 2.2.5-3 Temperature cyclingSubject the device to a low temperature of -40℃ for 30 minutes. Following by a hightemperature of +85℃ for 30 Minutes. Then release the device into the room conditionsfor 24 hours prior to the measurement. It shall meet the specifications in 2.2.5-4 Resistance to solder heatDip the device terminals no closer than 1.5mm into the solder bath at 260℃±10℃ for10±1 sec. Then release the device into the room conditions for 4 hours. The device shallmeet the specifications in 2.2.5-5 SolderabilitySubject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95%area of the terminals must be covered with new solder. It shall meet the specifications in2.2.5-6 Mechanical shockDrop the device randomly onto the concrete floor from the height of 1m 3 times. the deviceshall fulfill the specifications in 2.2.5-7 VibrationSubject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 2.2.www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 5 of 8

SAW FILTERHDF110L S36. REMARK6.1 Static voltageStatic voltage between signal load & ground may cause deterioration &destruction ofthe component. Please avoid static voltage.6.2 Ultrasonic cleaningUltrasonic vibration may cause deterioration & destruction of the component. Pleaseavoid ultrasonic cleaning6.3 SolderingOnly leads of component may be soldered. Please avoid soldering another part ofcomponent.7. Packing7.1 Dimensions(1) Carrier Tape: Figure 1(2) Reel: Figure 2(3) The product shall be packed properly not to be damaged during transportation and storage.7.2 Reeling Quantity1000 pcs/reel 7’’3000 pcs/reel 13’’7.3 Taping Structure(1) The tape shall be wound around the reel in the direction shown below.(2) LabelDevice NameUser Product Namewww.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 6 of 8

SAW FILTERHDF110L S3QuantityLot No.(3) Leader part and vacant position specifications.8. TAPE SPECIFICATIONS8.1 Tensile Strength of Carrier Tape: 4.4N/mm width8.2 Top Cover Tape Adhesion (See the below figure)(1) pull off angle: 0~15º(2) speed: 300mm/min.(3) force: 20~70g[Figure 1] Carrier Tape Dimensionswww.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 7 of 8

SAW FILTERHDF110L S3[Unit:mm]W F E P0 P1 P2 D0 D1 t1 t2 A B12.0±0.35.5±0.051.75±0.14.0±0.18.0±0.12.0±0.05Ø1.5±0.1Ø1.0±0.250.3±0.052.10±0.16.40±0.15.20±0.1[Figure 2][Unit:mm]A B C D E W t rØ330 Ø100 Ø13 Ø21 2 13 3 1.0±1.0 ±0.5 ±0.5 ±0.8 ±0.5 ±0.3 max. max.www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 8 of 8