NEW KITS FO

NEW KITS FOUltimate Learn to Solder KitThe Ultimate Learn toSolder Kit provides aperfect way to becomeproficient in soldering.Comes with 3 resistors,6 disc capacitors, 13integrated circuits anda pre-drilled glass epoxyPC board custom made forthese parts. You start with the 3 resistors, progress to the6 disc capacitors and then “hone” your skills by solderingthe 13 integrated circuits in. Instructions that come with thekit present illustrations of correct techniques and solderjoints. The kit is non-functional but provides one of the bestplatforms to obtain good soldering techniques. PC boardsize is 2” x 3”. Skill level 1.C7045 $4.95GM12 Geiger Counter KitThis low cost geiger counter kitdetects beta and gamma rayswith clicks and bright flashes ofred light. Operates from one 9Vbattery (not included) and usesa glass geiger mueller tube. Thiskit will detect radiation emittedby old radium watch hands,radioactive minerals, radioactiveorange dinner plates, older lanternmantles, background radiation from space and of courseradioactive contamination. Size of PC board is 1.37” x 3.69”.Background radiation here in Arizona measured with this kitis about 1cpm. Complete will all parts, glass geiger muellertube, PC board and instructions. Skill level 2.C7069 $69.95World’s Smallest Geiger CounterThis tiny fully assembled geigercounter is only 1.89” long x 0.86”wide x 0.46” thick. This geigercounter detects beta andgamma rays and emits clicksand bright red flashes oflight. Operates from one 9V battery (not included). Herein Arizona, this geiger counter emits about 2 to 4 clicksper minute from background radiation. Use this to detectradioactive minerals, old radium watch hands, radioactiveorange plates, lantern mantles, etc.C7061ASB $129.00 (Fully Assembled)“Speedster 500” Robot KitThis quick and zippy little robot zooms and turnsalong smooth hard surfaces while flashingits colorful “headlights”. The “Speedster500” robot operates from two tinyelectronic brains that consist offlashing rainbow LEDs. Each timeone of the LEDs flash, it causesthe robot to turn in a differentdirection. Operates from one 9Vbattery (not included). Size of board is 2.7” x 2”. Completewith all parts. Requires soldering. Skill Level 1. This robot isalso available fully assembled (9V battery not included).C7048 $13.95Also Available Fully AssembledC7048ASB $19.95 (No Soldering Required)GM22 Geiger Counter KitThe inexpensive GM22 Geiger Counter Kitis sensitive to beta and gamma rays anduses a glass SI-39 geiger mueller tube. Iteasily detects with clicks and flashesof red light all types of radioactiveminerals, radioactive isotopes,radioactive orange plates, oldradium watch hands, old lanternmantles, larger vaseline glass objects,cosmic rays from space and of course radioactive contamination.Operates from one 9V battery (not included). Size of PC board is1.3” x 4.1”. Background radiation in Arizona measured with thiskit is about 8 to 10 counts per minute. Complete with all parts,SI-39 glass geiger mueller tube, PC board and instructions.Skill level 2.C7060 $79.95Also Available Fully Assembled and TestedC7060ASB $99.95 (No Soldering Required)Ultimate Geiger Counter Kitwithout GM TubeThis kit operates from one 9V battery (notincluded) and produces about 450VDCfor use with many GM tubes (such as the LND712, SBM-10,SBM-19, SBM-20, SBM-21, SI-22, and SI-39 GM tubes).When radiation is detected the kit emits a clicking sound andflashes a bright red LED. Size of PC board is only 2.2” long x1.34”. Current drain is about 8mA. Complete with all parts, PCboard, and instructions (you will need to supply a 9V batteryand GM tube). Kit requires soldering. Skill level 2.C8600 $25.95Also Available Assembled (without GM Tube)C8600ASB $39.95 (No Soldering Required)Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

R 2013-2014Guitar Practice Amp Kit with CaseThe Guitar PracticeAmplifier Kit with Caseis perfect for any aspiringguitar musician! Operateson one 9V battery (notincluded) and delivers upto 1Watt of guitar musicfrom a built in 3-1/2” speaker, Featuresstandard 1/4” female jack for guitar cord, volume control,tone control, on/off switch, “on” indicator and compact caseof 4.25” square x 2.25” high. Comes with all parts, PC board,case and knobs. Skill level 2.C7058 $19.950-12V 1Amp Regulated Power Supply KitThis is similar to our G6929power supply kit, howeverthis kit uses a plug-inAC adapter to preventany contact with 120VACvoltage. It features aregulated and filteredvariable 0-12V output withup to 1Amp of availablecurrent. Uses an IC voltageregulator, heavy duty pluginadapter and circuit that uses 3 different LEDs to indicateapproximate voltages. Can power many electronic projects,radios, and small DC powered items. Size of PC board is1.85 x 2.85”. Complete with all parts, PC board, AC adapterand instructions. Skill level 1.C7055 $21.95Blinding White LED Current LimitingDriver KitSmall kit consists of a 1.4” x 1.5”PC board, IC regulator, and brightwhite high power SMD LED. TheSMD LED is pre-soldered on the PCboard, however you must solder theother components. Operates from6VDC up to 30VDC and producesa blinding white light. We have 3different versions of this kit -all usethe same PC board. Size of finished driver with LED kit is1.4” x 1.5” x 1” tall (no case available). Skill level 1.C7062A $5.95 (Single LED)C7062B $7.75 (Two LEDs)C7062C $9.00 (Three LEDs)SCI-TEC Rover Kit(No Soldering Necessary)This fun and educationalSCI-TEC Rover comes with 10activities/experiments. Thereis no soldering necessary forthis exciting project. Partssimply snap together and wiresare twisted onto connectors.Features a powerful motor with gear to propel your rover onalmost any surface (including most carpets). Operates on2 AA batteries (not included). Completed SCI-TEC Roveris about 9.5” long x 5” wide x 5” high. Learn about lamps,motors, circuits, and different types of propulsion! Completewith all parts and detailed instruction booklet. Skill level 1.C7056 $34.95Super Solar Light KitSmall Super Solar Light Kitrecharges daily from the sunand provides blinding white lightfrom 2 ultrabright cool white SMDLEDs. The LEDs in this kit arevery powerful and can provideemergency room lighting, camp tent lighting, etc. Nothing elseto purchase as this kit comes with a compact rechargeablebattery, solar panel, and LEDs. Note: due to the complexityof installing the SMD LEDs without damaging them we preinstallthem on the circuit board. All other components mustbe installed and soldered by the builder. Size of PC boardis about 2” x 3”. Complete with all parts, pre-install LEDs,rechargeable battery, and solar panel -no case available.Skill level 1.C7066 $11.95Large Area Solar Landscape Light KitThis Large Area Solar Landscape Light Kitfloods a 4 ft diameter area with bright lightfrom 2 super power SMD LEDs. The LEDsproduce such a bright light that you can’t lookdirectly at them when they are on. The lightuses a rechargeable battery (included) and asmall solar panel that charges it during the day fromsunlight. At night the light automatically comes on.Note: the powerful SMD LEDs come pre-installedon the PC board, however all other parts must beinstalled. No case available. Size of PC board is 2” x3”. Complete with all parts, PC board, battery, solarpanel, 17” long rod, and instructions. Skill level 1.C7067 $15.95Also Available as Discounted 4 Kit PackageC7067B $52.95 (Save $10.85 on this Package of 4)Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com

COMPUTER BASED TRAININGComputer BasedTraining CoursesChaney CBT courses introduce the basic concepts behindtheories and applications of electronics, by using detaileddiagrams, step by step electrical operational procedures,animations, and user feedback through quizzes and tests.Chaney CBT courses are ideal for both classroom andindividual use.C9006: All Five Courses Only $164.95Current, Voltage& ResistanceComputer Based TrainingLearn the concepts of: atoms, circuits,current, voltage, resistance, and the unitsto measure these parameters.C9001............$34.95 ea.Ohm’s LawComputer Based TrainingLearn the relationships of current, voltageand resistance of circuits through visualdemonstrations and mathematicalformulas.C9002............$34.95 ea.Resistor ColorCodeComputer Based TrainingLearn how to identify resistor valuesusing their color coded bands.Ideal for beginners.C9003............$34.95 ea.ComponentIdentificationComputer Based TrainingLearn and memorize the physicalappearance, name, schematic symboland function of 18 common components.C9004............$34.95 ea.Learn to SolderComputer Based TrainingLearn proper soldering techniques andtroubleshooting through animations andstep by step diagrams to build an actualkit (C6445 - See page 23).C9005............$34.95 ea.NEW!eachAvailable PowerPoint Courses:C7800 The AtomC7801 Current, Voltage & ResistanceC7802 Ohm’s LawC7803 Resistor Color CodeC7804 Component IdentificationC7805 SolderingeachC7806: All Six Courses Only $159.95NOTE:The PowerPoint files used in the PowerPoint courses require PowerPoint versions from 1997 and newer. PowerPointis usually part of the Microsoft Office Suite. Contact your IT Department to determine your version of PowerPoint.Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

If you are introducing soldering kits to your students, you’ll want one of these value packed exciting 4 in 1 packages.The student starts by following detailed instructions on “how to solder” and builds a non-functional “learn to solder” practice kit. This allowsthe beginner to gain hands-on soldering experience with actual components onto a PC board without worry about ruining kit functionality inthe process. After the proper soldering skills are mastered, the student can then progress on to each of the 3 remaining functional kits withexperience and confidence. Each remaining kit is battery operated, fully functional and can be mounted in an optional project box (if desired).At the conclusion, the student has built 1 non functional kit and 3 fully operating kits that he/she can enjoy. All 4 in 1 kits are rated Skill Level 1 andcome complete with all parts, PC board and detailed instructions. Each kit (except the non functional Learn To Solder Kit) operates from a 9V battery(not included). We offer five different “4 in 1” packages to choose from (each package is sold separately):Learn to Solder Kit Package “A”Package “A” starts off with our non-functional Learn to Solder Kit, which is an introductionto soldering and proper soldering techniques. After gaining some experience from theLearn to Solder Kit the student has three functional kits to build:SECRET IRRITATOR KIT - About once a minute, the kit will produce a 3 second long tone then remainsilent for another minute before making another sound. It is difficult for another person to find it becauseit remains silent for so long. Size of PC board: 2” x 1.25”.ELECTRONIC SIREN KIT - This kit produces the upward and downward wail of a “police siren” as you pressand release a small pushbutton. Uses a small speaker. Size of PC board: 2” x 1.25”.MULTICOLOR LED FLASHER KIT - This kit uses 2 red LEDs, 1 yellow and 1 green LED. Features a controlthat can be adjusted to cause 2 groups of 2 LEDs to alternately flash or all 4 LEDs flash together. Features C6880 PACKAGE “A” $15.25reliable IC circuitry. Size of PC board: 2” x 1.25”.Optional Boxes for above kits: Type 1 C6363 $1.80 ea. (3 boxes for 3 kits)Learn to Solder Kit Package “B”Package “B” starts off with our non-functional Learn to Solder Kit, which is an introduction tosoldering and proper soldering techniques. After gaining some experience from the Learn toSolder Kit the student has three functional kits to build:PHASOR RAY KIT - This kit generates the sound of a phasor ray gun and flashes a brilliant orange light.Uses a small speaker, a crystal clear lens LED and 2 transistor circuit with adjustable sound control.Size of PC board: 2” x 1.25”.RED STAR FLASHER KIT - This kit will really attract attention as it flashes a bright red star made up of six5mm red LEDs. Features simple and reliable 2 transistor circuit. Size of PC board: 2” x 1.25”.YES/NO DECISION MAKER KIT - Simply press the button on your decision maker kit and two brightlycolored LEDs will begin to flash. As soon as you release the button, one of the LEDs will remain on. The C6881 PACKAGE “B” $14.75green LED indicates yes and the red LED indicates no. Uses IC circuitry. Size of PC board: 2” x 1.25”. Optional Boxes for above kits: Type 1 C6363 $1.80 ea. (3 boxes for 3 kits)Learn to Solder Kit Package “C”Package “C” starts off with our non-functional Learn to Solder Kit, which is an introductionto soldering and proper soldering techniques. After gaining some experience from theLearn to Solder Kit the student has three functional kits to build:LED FLASHER KIT - This kit uses a 555 timer IC to alternately flash a red and green LED. The kit makesa great attention getter. Operates from 5 to 9VDC. Size of PC board: 1.5” x 1”.IC DECISION MAKER KIT - When you press a small on board switch a bright green LED and a brightred LED begin to alternately flash. As soon as you release the button, one of the LEDs stays onindicating the decision. Uses a CMOS IC. Size of PC board: 1 3/8” x 1 7/8”.TEMPERATURE WARNING KIT - The kit can be set to indicate a rise or drop in temperature by simplyadjusting its control knob for ambient temperature. As the temperature changes, a Red or Green LED C6934 PACKAGE “C” $14.95indicates over or under temperature from its setting. Size of PC board 2” x 1.8”.Optional Boxes for above kits: Type 1 C6363 $1.80 ea. (3 boxes for 3 kits)Learn to Solder Kit Package “D”Package “D” starts off with our non-functional Learn to Solder Kit, which is an introduction tosoldering and proper soldering techniques. After gaining some experience from the Learn toSolder Kit the student has three functional kits to build:COIN TOSSER KIT - This kit uses 3 transistors and 2 LED circuits to make decisions or replace cointossing. Features 1 red and 1 green LED that flash when you touch the sensor wires. When you quittouching the sensor your decision is shown by the LED that remains on. Size of board: 1.6” x 2.2”.SUPER LED FLASHER KIT - This kit features a two IC circuit which alternately flashes 4 LEDs: 2 red, 1yellow and 1 green. Size of board: 2” x 2”.NO ENTRY KIT - This Kit features a custom designed full color label and a bright flashing red LED. Perfectfor bedrooms, dorm rooms, teachers’ desks, offices, or any other place that you would like to express C6935 PACKAGE “D” $15.50yourself. Size of PC Board: 3 1/4” x 4 3/4”.Optional Boxes for above kits: Type 1 C6363 $1.80 ea. (2 boxes for 2 kits) and 1 Type C Base C6622 $2.50 ea.Learn to Solder Kit Package “E”Package “E” starts off with our non-functional Learn to Solder Kit, which is an introductionto soldering and proper soldering techniques. After gaining some experience from theLearn to Solder Kit the student has three functional kits to build:ELECTRONIC SIREN KIT - This kit produces the upward and downward wail of a “police siren” as youpress and release a small pushbutton. Uses a small speaker. Size of PC board: 2” x 1.25”.YES/NO DECISION MAKER KIT - Simply press the button on your decision maker kit and two brightly coloredLEDs will begin to flash. As soon as you release the button, one of the LEDs will remain on. The green LEDindicates yes and the red LED indicates no. Uses IC circuitry. Size of PC board: 2” x 1.25”.LITTLE JITTERBUG ROBOT KIT - This kit uses a light sensor to come alive in darkness and scootaround with the help of a tiny vibrating motor. Customize its antennas and legs. Flashing LED allows C6994 PACKAGE “E” $16.75you to find this little critter. Operates on a 3V CR2430 coin battery (included).Optional Boxes for above kits: Type 1 C6363 $1.80 ea. (2 boxes for 2 kits)4 in 1 Introduction to Solder KitsChaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com

RadiationUltra Sensitive Giant Geiger Counter KitAlpha, Beta & Gamma Sensitive Miniature Geiger Counter KitDemonstration VideoAvailable on our WebsiteOur largest and most sensitive geiger counter kit uses aRussian Geiger Mueller tube. This tube is 0.75” in diameterx 7.2” long and because of its large surface area it is sosenstive to beta and gamma rays that the background counthere in Arizona on this kit is about 100 counts per minute.Operates on one 9V battery (not included). Flashesa bright red LED and “clicks” from a small onboard speaker with each particle detection. Sizeof PC board is 7-13/16” x 1-7/16”. Complete withall parts, GM tube, and instructions. Requiressoldering. No case available.Ultra Sensitive Giant Geiger Counter Kit............C7026 $149.00Miniature Geiger Counter Kit measures alpha, beta, and gammarays using a mica window GM tube type 6108. The miniaturemica window tube is only 1.6” long x 0.35” diameter. The tubewas made for the US Navy during the Cold War and is precisionmade. This kit has its sensitive detection window at the end of thetube at about 0.3” diameter so you that you can pinpoint specificsources of radioactivity. This kit uses a 555 IC, a small metalspeaker, and a blue-green LED to provide indication of radiationwith both clicks and flashes of bright light each time radioactiverays strike the mica window. Comes with all parts, PC board, andinstructions. Operates from one 9V battery (not included). Thiskit requires soldering. Skill level 2. Please do not purchase thiskit if you have never soldered an electronic kit before.Replacement Geiger Mueller Tube C7291 $80.00optional plastic Type 2 box C6364 $2.40Alpha, Beta & Gamma Sensitive Miniature Geiger Counter Kit............C6998 $149.95Highly Sensitive Beta Gamma Geiger Counter KitVery sensitive geiger counter kit uses a russian geiger tube which is even moresensitive than the tube used in our C6979 kit. This kit can detect radiationfrom contamination, old radium watch hands, certain orange colored plates,lantern mantles, radioactive minerals and even radioactive vaseline glassmarbles. Produces familiar clicking sound and lights up a bright red LED witheach click. Detects background radiation from cosmic rays (here in Scottsdale,Arizona the count is about 14 per minute). When we placed a vaseline glassmarble next to the tube, the count went to about 50 per minute. Operatesfrom one 9V battery (not included). Complete with all parts, PC board, andtube. As a bonus we will include a vaseline glass marble. PC board size is2.5” x 1.5”. Skill level 2.Replacement Geiger Mueller Tube C7292 $60.00optional plastic Type 2 box C6364 $2.40Highly Sensitive Beta Gamma Geiger Counter Kit...C7023 $129.00Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

DetectionSensitive Geiger Counter KitOur Sensitive Geiger Counter Kit uses a Russian Geiger Mueller tubeand is sensitive to Beta and Gamma rays. Want to know if that orangecolored plate that was all the rage in the 60’s is radioactive, how aboutyour dad’s radium dial watch, or the mantles on your camping lantern -thiswill tell you! Produces the familiar audio clicks and lights up a blue/greenLED in response to radioactive sources. Random clicks are even heardfrom your kit as cosmic rays strike the tube! Uses a Russian GM tube thatwas made during the cold war (we test every one for proper operation),various resistors, capacitors, and a special miniature speaker. Operatesfrom one 9V battery (not included). Comes with all parts, PC board, GMTube and instructions. Size of PC board 4-5/16” x 1-1/2”. Skill Level 2.Sensitive Geiger Counter Kit.................................................................................C6979 $101.95Digital Display Geiger Counter KitThis sensitive geiger counter kit uses a Russian geiger mueller tubeand a microcontroller IC to measure and display radiation countson a 3 digit display. The counter is sensitive to beta and gammarays and will indicate the presence of radiation with a click fromthe built in speaker and a brilliant blue-green flash from an LED. Inaddition the microcontroller IC outputs the count to a pale yellow 3digit display (the display is visible indoors but not bright enough tobe viewed outdoors in order to conserve battery life). The uniquefeature of the microcontroller digital output is that you can selecteither counts per minute or total counts to be displayed. The totalcounts display uses a unique setup with multiplier LEDs to indicate10x 100x and 1000x counts allowing the counter to display 999,000before an overflow LED lights up. In the lower range (from 0 - 999)no multipliers are used. The microcontroller is fully programmed andthe kit comes with: all parts, PC board, microcontroller, instructionsand Russian geiger mueller tube made during the cold war (every tube is verified for proper operation). Operates from one 9Vbattery (not included). The size of the PC board is 4.25” x 3.2”. Skill level 2.Please have soldering experience before building this kit as some components use high voltage where faulty solderingwill cause problems with kit operation.Replacement Geiger Mueller Tube C7330 $40.00optional plastic Type 5 box C6367 $3.90Digital Display Geiger Counter Kit........................................................................C6981 $139.95Micro Geiger Counter KitDemonstration VideoAvailable on our WebsiteDemonstration VideoAvailable on our WebsiteThis Micro Geiger Counter Kit is only 1.3” x 1.9” x .6” thick. It operates on one 9V battery (notincluded) and is sensitive to Beta and Gamma rays. Uses a tiny .6” long Russian Geiger Muellertube and a one IC circuit. Great for detecting radiation from radioactive minerals, old campinglantern mantles, some orange colored dinner plates, old radium dial watches etc. Emits loudclicks and bright blue green flashes of light when radioactive rays strike the tube. Very compactand unique! Comes with all parts, PC board, GM tube and instructions. Skill level 3.Replacement Mini Geiger Tube C7331 $45.00optional plastic Type 2 box C6364 $2.40Micro Geiger Counter Kit...............................................C6986 $99.00Replacement Geiger Mueller Tube C7330 $40.00optional plastic Type 4 box C6366 $3.60Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com

GREEN ENERGY andCheck Out Our:54 in 1 Solar House“Green Energy” LabMakes a GreatIntroduction toSolar EnergySee Page 13for Full DetailsC7041$49.95No Soldering Solar PoweredSpeed Car KitOur Solar Powered Speed CarKit features a high power6VDC lightweight 4 3/4” x 11/4” silicon solar panel thatyou attach along with wheelsto a 2 7/8” x 2 1/8” body. Has anefficient super speed motor driving 11/2” Dia. wheels with a rubber band belt drive. Simple to buildand fun to operate. Race others to see who has the fastest car.In full sunlight our test car traveled 10 feet in only 3 seconds.Complete with all parts, motor, solar panel and instructions. NoPC board and no soldering needed for this kit.Skill Level 1. Great for Science Camp.C6904 $19.95Super Solar Light KitSmall Super Solar Light Kitrecharges daily from the sunand provides blinding whitelight from 2 ultrabright coolwhite SMD LEDs. The LEDsin this kit are very powerful andcan provide emergency roomlighting, camp tent lighting, etc. Nothing else to purchase asthis kit comes with a compact rechargeable battery, solarpanel, and LEDs. Note: due to the complexity of installingthe SMD LEDs without damaging them we pre-install themon the circuit board. All other components must be installedand soldered by the builder. Size of PC board is about 2” x3”. Complete with all parts, pre-install LEDs, rechargeablebattery, and solar panel -no case available. Skill level 1.C7066 $11.95Sun SpinnerRobot KitThis colorful robot featuresa see through green domehead that spins when exposedto sunlight. The robot is about 6” talland 4” diameter. As the head spinsthe robot shakes, sometimes creepsslowly but at the same time it takesthe sun’s rays and stores them in itsbuilt in rechargeable battery. At nighta built in LED flashes, even thoughthe head stops spinning. The nextday when full sunlight strikes thehead again, the robot’s head beginsto spin and the cycle repeats. Uses a small motor, solar paneland a rechargeable battery. Complete with all parts, PC boards,dome and rechargeable battery. Skill level 1.C6946 $19.95Solar Bug KitThis totally solar powered bugnever needs batteries! It producesa sound similar to a crazed cricketwhenever the sun shines on it. Put itin your garden to surprise and entertainguests. It can be heard from quite adistance away. Your tiny SolarBug caneven be placed under a lamp and will “chirp” happily. Your uniquelooking SolarBug can be “customized” or painted to look like ascorpion, strange beetle, etc. You’ll never need to buy batteriesfor your SolarBug as it uses 4 tiny solar electric power generators.Size of PC board is about 2” x 15/16”. Complete with all parts, PCboard and instructions. Skill Level 1.C6843 $10.25Solar Camping Light Kit10 in 1 Solar LabC6853 - Page 18Solar Powered BoatC6983 - Page 19This impressive, light weight only (4oz),“Green Energy” camping light is theperfect camping companion. Whileyou’re hiking, kyaking or canoeing, the2” x 3” rechargeable solar cell chargesthe built in battery by sunlight so whennight time settles in, you will have hoursof illumination. This kit features a smallslide switch so you can light-up yourimmediate camp surroundings when switched to the “full power”position (4 ultrabright LEDs having approx. 2 hrs of illumination). Oryou may choose to relax in your tent with the “nightlight” position. (1warm white LED offers all night illumination). The light is housed in thebottom of your recycled 2 litter soda bottle (not included) and hungby an “L” bracket. Comes with PC board, solar panel, rechargeableNiMH battery, LEDs and all parts (no soda bottle included). Requiressoldering. Size about 2” x 3” x 1.2”. Skill Level 1.C6985 $14.9510Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

SOLAR POWER KITSLarge Area Solar Landscape Light KitThis Large Area Solar Landscape Light Kitfloods a 4 ft diameter area with bright lightfrom 2 super power SMD LEDs. The LEDsproduce such a bright light that you can’t lookdirectly at them when they are on. The lightuses a rechargeable battery (included) and asmall solar panel that charges it during the day fromsunlight. At night the light automatically comes on.Note: the powerful SMD LEDs come pre-installedon the PC board, however all other parts must beinstalled. No case available. Size of PC board is 2” x3”. Complete with all parts, PC board, battery, solarpanel, 17” long rod, and instructions. Skill level 1.C7067 $15.95Also Available as Discounted 4 Kit PackageC7067B $52.95 (Save $10.85 on this Package of 4)Solar Powered Brilliant Walklight KitThis small Solar Powered WalklightKit is much brighter than thecommon solar walklight and it featuresthree brilliant white LEDS that produceover 10,000 mcd (millicandelas) luminousintensity each. These white LEDS glowbrilliantly when it gets dark for up to 10 hourseach night from the charge stored in the powerful3.6V 750mAh NiMH battery (hours of glowing may bereduced in areas of the country with less daily sunshine). Eachday the battery recharges again from the suns output on the 2small solar panels on the top of the kit. The kit sits on top of astainless steel 6mm diameter 17” long rod that you tap into theground. Overall size of finished kit is about 4”L x 2.4”W x 1.7”Tall(excluding rod). Note this kit uses a PC board that is purposelynot drilled (the components mount directly to the foil pads to keepout moisture) and we recommend covering the electronic partswith Household Goop (not included - available in the glue sectionin most stores) to protect them from moisture. Complete with allparts, solar panel, battery, rod and instructions. Skill Level 2.• 4 for $39.95 • 8 for $74.95 • C6930 $10.95Glass Solar Powered Propeller ProjectThis awesome kit requires no soldering. Justpush the propeller onto the motor, twist thewires from the round 4” glass solar panelonto the motor terminals and it is ready togo. Great for demonstrating solar power.Whenever sunshine strikes the glass panelthe propeller turns! Complete with all parts,pre-wired solar panel and instructions (no case or motor mountincluded). Great for science fairs, science camps, scouts, etc.No soldering or PC board required.C18976 $6.00World’s BrightestLandscape Light KitThis large solar powered landscape light uses two220,000MCD warm white 5-chip 10mm LEDs. The lightoutput of this is unlike any other solar powered landscapelight available on the market today for its very bright illumination!It uses a powerful 5” diameter solar panel, a3.6V 750mAh rechargeable battery and a 2 transistor circuitwith CDS cell sensor. Just build the kit, cover the electroniccomponents with Goop (not included) to insulate from theelements and push the heavy duty stake into ground whereyou wish position the light. Each day the light will automaticallyturn on when it gets dark. Requires Soldering. Skill Level 1. Sorry,no case available.C7021 $14.95optional Glass Cover C7500 $4.95Also Available in Discounted PackagesC7021B 4 Kits for $49.95 (Save $9.85)Solar PoweredBoat ActivityIdeal for AllGrade LevelsSee Page 19for Full DetailsSolar Nite Screamer KitC6983$24.95Here is a great little kit which is sureto disturb everyone! The Solar NiteScreamer Kit stores up the sun’senergy during the day then when itgets dark it produces a high pitchedtone which typically goes on all night!The next morning the kit goes silent and stores up the sun’senergy for another “screaming night”. No batteries to buy orreplace -just hide the kit on a roof, tree, etc, and leave it there!Size of PC board is 1.3” x 3”. Complete with tiny solar panel,rechargeable battery and all parts, PC board and instructions.Skill level 1.optional plastic Type 2 box C6364 $2.40 C7022 $9.95Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 11

17 in 1 Microcontroller lab17 in 1Deluxe Microcontroller Exploration LabAre you looking for a way to introduceyour students to the exciting worldof microcontrollers? Have you beenoverwhelmed with the difficulty of finding everything you needin one convenient package? Well look no further as we havedeveloped a complete microcontroller introduction course. Ournew 17 in 1 Deluxe Microcontroller Exploration Lab was developedas an introduction to microcontrollers and requires no previousknowledge of microcontrollers or programming languages.This is the perfect hands-on lab that gives your studentsvaluable practical experience as they build each experiment. All ofthe source code (written in C) is provided on a CD rom and eachexperiment has a hex file (the compiled source code) that can beprogrammed onto the microcontroller using a Microchip PICkit2programmer. The PICkit2 programmer plugs into a USB port onyour computer and allows you to program your microcontroller witha hex file (the compiled source code). The PICkit2 programmeris included with the complete version of the kit and is necessaryto program the microcontroller. Advanced users or students thatare familiar with the C programming language will be able tofollow the source code that was used to generate the hex file foreach experiment.*This lab requires no soldering as each experiment isbuilt on a reusable solderless breadboard using the suppliedelectronic components. At the heart of this lab is a microntrollercircuit comprised of: the Microchip PIC18F2410 microcontroller,a crystal, a voltage regulator, and other components. Thismicrocontroller plugs directly into the breadboard and controlsall 17 experiments.A printed instruction manual with detailed illustrationsguides students through the lab. The instruction manual startswith an introduction to microcontrollers and gives an overview ofwhat microcontrollers can do and how they are used in today’smodern digital circuits. Information on interfacing the PICkit2programmer with your computer is also included. From here,the student will begin to build the experiments. All experimentsoperate from one 9VDC battery (not included). Each experimenthas a detailed theory of operation, a complete wiring diagram,the circuit schematic and a basic overview of the source code.Some of the exciting topics that are covered in this course arebasic digital circuits, logic levels, pull up resistors, sensors, LEDsand LED displays, binary and hexadecimal numbers, pulse widthmodulation (PWM), analog to digital conversion, stepper motors,LCD displays, and more. Please see the complete list of theexperiments.The 17 in 1 Deluxe Microcontroller Exploration Lab comeswith all the parts, microcontroller, a breadboard, instructionmanual and source code CD-ROM. Requires one PICkit2programmer (included with the C7043) and a Windows XP®,Windows 2000®, or Windows 98SE® computer with availableUSB port for operation.Complete 17 in 1 Deluxe MicrocontrollerExploration Lab with PICkit2 ProgrammerC7043 $134.95Also Available without the ProgrammerComplete 17 in 1 Deluxe MicrocontrollerExploration Lab WITHOUT PICkit2 ProgrammerC8043 $99.95The Microchip name and logo, the Microchip logo, MPLAB, PIC, PICkit are registered trademarks of Microchip TechnologyIncorporated in the U.S.A. and other countries. All other trademarks mentioned herein are property of their respectivecompanies.INCLUDES:• PIC18F2410 Microcontroller• High Quality Breadboard• All necessary Electronic Components• PICkit2 Programmer (Included with the C7043)• Fully Illustrated Printed Instructional Manual• Source Code CD-ROM17 in 1 Deluxe Microcontroller Lab Experiments:Instructional Experiments1 Experiment 1 Dual LED Flasher2 Experiment 2 Dual Speed Single LED Flasher3 Experiment 3 Darkness Alarm (CDS Cell)4 Experiment 4 IR Sensor5 Experiment 5 Stepper Motor6 Experiment 6 Sequential 8 LED Flasher7 Experiment 7 Seven Segment Display8 Experiment 8 8 Bit Binary Counter9 Experiment 9 4 Bit Binary/Hexadecimal Counter10 Experiment 10 Light Meter (Bargraph Display)11 Experiment 11 Sound Meter (Bargraph Display)12 Experiment 12 PWM LED13 Experiment 13 Music Maker14 Experiment 14 Intro to LCD15 Experiment 15 LCD Temperature Display (ºF or ºC)16 Experiment 16 LCD Clock (Hours, Minutes, Seconds)17 Experiment 17 RGB PWM Color FaderUse Your Computer to Program a MicrocontrollerMicrochip PICkit2Programmer*NOTE: This course was not developed to be a tutorial or instructional course for C programming.Advanced users my install Microchip’s MPLAB® IDE and MPLAB® C18 Compiler software (not included)for advanced use with the supplied source code.12Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

54 in 1Solar House “Green Energy” LabHave you seen a house with a solar panel on the roof and wondered how it produces electricity?In response to increasingly high electricity costs and the overall well being of our environment,advanced technologies in solar energy has made it possible for home owners and businesses toinstall Photovoltaic Solar Panels to convert sunlight to usable electricity and heat. With this in mind,we have designed this course for the inquisitive student that wants to gain an understanding of howdifferent technologies using green or alternate energy can be used in the home.In this course, we will create our own model house made of Plexiglas and install an amorphoussilicon glass solar panel to simulate how we can harness the sun’s energy into one’s house. Thesolar panel that we will be using will provide the energy used for all of our experiments. We willperform most experiments with solar energy stored in a battery that has been charged from oursolar panel along with a re-useable solderless breadboard.The fully illustrated and detailed manual included in this course will introducethe student to some basic technology and fundamental conceptsused in common house hold devices such as lighting,thermostats, fire alarms, and burglar alarms. In orderto study these technologies, we are going to studysolar panels, motors, fans, resistors, diodes, LEDs,switches, lamps and batteries. The easy-to-followpictorial diagrams will guide the student through 26chapters containing a variety of activities and usefulexperiments along with fun and interesting facts relatingto solar energy.54 in 1 Solar House LABThis course offers a hand on approach that is applicablefor use in grades junior high up through college.All parts to create the model house, along with the necessarycomponents, wires, breadboard, solar panel, and detailedinstruction manual are included. No soldering or additionalbatteries required. Re-usable and safe to use.Skill Level 1C7041 $49.9554 in 1 Solar House “Green Energy” Lab Contents:Chapter 1Chapter 2Chapter 3Chapter 4Chapter 5Chapter 6Chapter 7Chapter 8Chapter 9Chapter 10Chapter 11Chapter 12Chapter 13Chapter 14Chapter 15Chapter 16Chapter 17Chapter 18Chapter 19Chapter 20Chapter 21Chapter 22Chapter 23Chapter 24Chapter 25Chapter 26AppendixIntroductionEnergy SourcesConstructing the Solar HouseSolar SystemsSolar CellsSolar PanelsInvertersGrid-Tied vs Off-GridBatteriesMeteringDisconnectCharging Batteries with Solar PowerResistorsSwitchesCeiling FansDiodesLEDsLightingSeries Circuit vs Parallel CircuitsOutdoor LightingTransistorsConductorsWater Flood AlarmDoorbellThermostatsBurglar AlarmFire AlarmAdditional InformationExperiment 1Experiment 2Experiment 3Experiment 4Experiment 5Experiment 6Experiment 7Experiment 8Experiment 9Experiment 10Experiment 11Experiment 12Experiment 13Experiment 14Experiment 15Experiment 16Experiment 17Experiment 18Activity 1Activity 2Activity 3Activity 4Activity 5Activity 6Activity 7Activity 8Activity 9Activity 10Battery Charging with solar PowerSwitchesFansDiodesLEDsLED Lighting Color TemperatureIncandescent Lamps vs LEDsParallel CircuitsSeries CircuitsAutomatic Outdoor LightingTransistorsConductorsWater Flood AlarmDoorbellThermostatBurglar AlarmFire AlarmElectronic CandleEnergy ActivitySolar Systems ActivitySolar Cells ActivitySolar Panels ActivityBatteries ActivityResistors ActivityCeiling Fans ActivityDiodes ActivityLEDs ActivityConductors ActivityChaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 13

26 in 1 ROBOTICS LABCHANEYC-100026 in 1Robotics Experimenter LabHave you noticed how robots arebecoming more and more a part of our lives?From practical robots to novelty robots,industrial applications to sciencefiction, robots are a part of our modernlife. We designed this course to givestudents an introduction to what a robotis and how robots sense the world aroundus. This course is the perfect introductionto the exciting field of robotics becauseit offers a hands on experience for yourstudents as they build and experimentwith different robots. For example, your students will beable to build a robot that “sees” in the dark and a robotthat can sense a puddle of water all while learning aboutelectronics and robotics. A complete list of the robotsincluded with this lab is shown below.A detailed Instruction Manual is included with this Labthat contains all of the information that your students will need to successfully complete the robot experiments. This labfeatures a detailed introduction of what a robot is and what robots do. After the introduction, the student will begin tobuild a basic robotic platform from which all of the other experiments will be based. The robots progress in complexityand each robot is fun to build and operate. Some of the topics covered include: Sensor Technology, Infrared (IR) Vision,Transistor Operation, Integrated Circuits, Relay Operation, Electronic Motors and basic electronic concepts includingOhm’s law and component identification.This lab is completely reusable and designed with the student in mind. Each experiment has been thoroughly testedand developed to offer the maximum educational value. Each robot that the student will build comes with detailed12326 in 1 Robotics Experimenter Lab Manual Contents:Instructional ExperimentsExperiment 1 Building the Robot PlatformExperiment 2 Testing the Basic Robot Base, Drive System & Power SystemExperiment 3 Electronic Component Identificationinstructions, illustrations, schematic, wiring guide andtheory of operation. All experiments/robots operate onone 9V battery (not included) and use the same robotchassis and relay control board. The relay control boardand the optical eye sensor board require soldering forassembly (see C6907 below for a pre-soldered version).4 Experiment 4 Assembling the Relay Control Board & Optical Eye Sensor BoardAll of the necessary components and wires are supplied5 Experiment 5 Testing the Relay Control Board & Optical Eye Sensor Boardalong with a re-useable solderless breadboard and6 Experiment 6 Basic Robot Turnsdetailed instruction manual. This lab will captivate andRobot Experimentsexcite your students and is a tremendous educational7 Robot 1 Direction Changing Desktop Robotvalue.8 Robot 2 “Hollywood Starbot” Light Activated Robot9 Robot 3 “The Moth” Light Following Robot10 Robot 4 Nocturnal Explorer Robot11 Robot 5 Shadow Controlled Robot12 Robot 6 “The Pirate” Treasure Finding Robot13 Robot 7 The Dancing Robot14 Robot 8 “The Nightcrawler” Optical Obstacle Avoider Robot15 Robot 9 Repelled by Dark Surfaces Robot16 Robot 10 Target Practice Robot17 Robot 11 Infrared Navigator Robot18 Robot 12 Infrared Racer Robot19 Robot 13 Acrophobic Robot20 Robot 14 Fearless Explorer Table Navigator Robot21 Robot 15 Phototropic Robot22 Robot 16 Abracadabra Magic Spell Robot23 Robot 17 “Night Vision” Infrared Obstacle Avoider Robot24 Robot 18 The Line Tracer Robot25 Robot 19 “Mr. Puddle” The Water Detecting Robot26 Robot 20 “The Wall Flower” Wall Follower RobotTroubleshooting InformationINCLUDES:• High Quality Breadboard• 4 Wheels, 2 Motors, and VariousMechanical Parts• All necessary Electronic Parts• Fully Illustrated Instructional Manual• Relay & Sensor Boards (requires soldering)C6890 $52.95Comes with relay and sensorboard unassembledor the Same Lab and NO Soldering Needed!Relay Control Board Optical Eye Sensor BoardComplete 26 in 1 Robotics Lab with pre-assembled andsoldered Relay Control Board and Optical Eye Sensor Board.Exact same kit as above except we solder it for you so that thereis absolutely no soldering needed for assembly.Comes with relay and sensor boardPre-assembled & SOlderedC6907 $64.9514Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

44 in 1Super Valuable& ReusableCommunications & Opto-ElectronicsDeluxe Exploration LabAbsolutely the best introduction to Radio Communications and Opto-Electronics.Build:• PA Systems with Microphone and Speakers• AM Radio Receiver• AM & FM Broadcast Stations• Optical Receivers & Transmitters• Infrared Communication Links• Fiber Optic Communication Links• IR Remote Control Transmitters and Receivers• IR Proximity Detectors...and Many More!This lab was created with the student in mind. It will keep the handsand minds of the students busy building amazing communicationexperiments by using wire, fiber optics, radio waves, light andinfrared links. No previous knowledge or experience is required.Try it! We are sure you will be completely satisfied with this excitingand fun Chaney Communications Lab.Lab includes:• Over 50 Electronic Components• 2 Solderless Breadboards• 64 Page, Fully Illustrated Manual• A Tuner Board(Requires Soldering)C6763 $45.95Introduce your students to the basics ofvarious communication systems with thisexciting and reusable CommunicationsTraining Lab.44 in 1 Communications & Opto-ElectronicsDeluxe Exploration Lab Manual Contents:1 Introduction2 Parts Inventory3 PreactivityInstructional Lessons & Experiments4 Lesson 1 Electronic Communication5 Experiment 1 Morse Code Generator6 Experiment 2 1-Wire Telegraph System7 Experiment 3 2-Wire PA System8 Experiment 4 Coaxial Cable PA System9 Lesson 2 Alternating Current (AC) Characteristics10 Lesson 3 Radio Communication & Electromagnetic Waves11 Lesson 4 Frequency Spectrum12 Lesson 5 Wireless Lightwave Communication13 Experiment 5 Opto Receiver14 Experiment 6 Opto Transmitter15 Experiment 7 Infrared Opto Transmitter16 Experiment 8 Opto Voice Transmitter17 Experiment 9 Infrared Opto Voice Transmitter18 Experiment 10 Opto Music Transmitter19 Experiment 11 Infrared Opto Music Transmitter20 Lesson 6 Fiber Optics Communication21 Experiment 12 Introduction to Fiber Optics22 Experiment 13 Fiber Optics - Dual Color Transmission23 Experiment 14 Fiber Optics - Multiple Fiber Transmission24 Experiment 15 Fiber Optic Audio Link25 Experiment 16 Infrared Fiber Optic Audio Link26 Experiment 17 Infrared Remote Control Receiver27 Experiment 18 Infrared Remote Control Transmitter28 Experiment 19 Audible Infrared Remote Control Receiver29 Experiment 20 Infrared Proximity Detector30 Experiment 21 Audible Infrared Proximity Detector31 Experiment 22 Infrared On/Off Remote Control Switch32 Experiment 23 Simple Infrared Transmitter33 Lesson 7 AM/FM Radio Communication34 Experiment 24 Crystal Radio Receiver35 Experiment 25 Basic AM Receiver36 Experiment 26 AM Radio Receiver with Speaker37 Experiment 27 AM Radio Receiver with Speaker and Volume Control38 Experiment 28 AM Tone Transmitter39 Experiment 29 AM Code Transmitter40 Experiment 30 AM Broadcast Station41 Experiment 31 AM Microphone Transmitter42 Experiment 32 FM Tone Transmitter43 Experiment 33 FM Code Transmitter44 Experiment 34 FM Microphone Transmitter44 in 1 COMMUNICATIONS LABChaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 15

HABCDEJ35 in 1 DELUXE DIGITAL LAB10 15 20 25 30 35 40 45 50 55 6010 15 20 25 30 35 40 45 50 55 6035 in 135 in 1 Deluxe Digital Exploration Lab Manual Contents:Tips on Building the ExperimentsThe Universal Solderless Breadboard: Use and PreparationInstructional Lessons & Experiments1 Lesson 1 Introduction to Digital Electronics2 Experiment 1 The Logic Probe: “The Tool”3 Experiment 2 The YES Logic Circuit: “The Buffer”4 Experiment 3 The NOT Logic Circuit: “The Inverter”5 Experiment 4 The AND Logic Gate6 Experiment 5 The OR Logic Gate7 Experiment 6 The NAND Logic Gate8 Lesson 2 Components, Gates and ICs9 Experiment 7 The NOR Logic Gate10 Experiment 8 Building the Six Basic Logic Gates Using Only NOR Gates11 Lesson 3 Combinational & Sequential Circuits,Boolean Algebra & Timing Diagram12 Experiment 9 “The Clock”: Astable Multivibrator13 Experiment 10 The 555 Timer IC14 Experiment 11 “The Timer”: Monostable Multivibrator15 Experiment 12 “The Flip–Flop”: Bistable Multivibrator16 Experiment 13 Reaction Challenge Game17 Lesson 4 The Binary Numbering System18 Experiment 14 The Binary Counter/Divider19 Experiment 15 Manual Binary Counter & Switch Debouncing20 Experiment 16 The BCD Counter (Decade Counter)21 Experiment 17 Touch Activator ON/OFF Switch22 Experiment 18 Seven Segment Display Decoder23 Experiment 19 “0 to 9” Counter with Display24 Experiment 20 Lucky Number Generator25 Experiment 21 Electronic Die Game26 Experiment 22 0 to 9 Photoelectric Counter27 Experiment 23 Sequential LED Flasher28 Experiment 24 Triple Answer Decision Maker29 Experiment 25 “10 by 10” Reaction Game30 Experiment 26 Touch Activated Brightness Control31 Experiment 27 Macho Meter32 Experiment 28 “Go for the Gold” Game33 Experiment 29 0 to 99 Counter with Display34 Experiment 30 0 to 99 Photoelectric Counter35 Lesson 5 Troubleshooting TechniquesNo Soldering Required& ReusableDeluxe Digital Exploration LabThis lab does not require soldering, is reusable, and contains 5lessons and 30 meaningful and exciting digital experiments. Thebooklet is fully illustrated with easy-to-follow pictorial diagramsand schematics. It is designed so that the teacher does not needto be involved (unless he or she desires to be). It is applicablefor use in junior high grades up through college. All experimentsoperate on one 9V battery (not included) so there are no dangerousvoltages involved. Compared to other similar digital labs, you willfind that this lab is far superior in that it contains a wider varietyof digital components, including a double binary counter and two7-segment displays, allowing the students to build “0 to 99” digitalcounters instead of only “0 to 9”. This lab also includes LEDs ofthree different colors (red, green, and yellow), and uses a uniformprewired breadboard system which is applied in each experiment,along with reverse polarity protection and a switch wire to preventdamage to the ICs or battery snap. This lab also covers more digitaltopics such as Boolean algebra, timing diagrams, frequency andduty cycle formulas, troubleshooting techniques. The lab includes a96 page, fully illustrated manual, a large solderless breadboard, 6integrated circuits, a CDS photocell, plus all other parts necessaryto perform each experiment. Just supply a fresh 9V battery andnothing else is required to perform all the experiments in thebook. The Complete 35 in 1 Deluxe Digital Exploration Lab isself-contained and ready-to-use!C6721 $35.95The perfect lab to introduce studentsto Digital Electronics andComputer Technology!Optional Logic Probe: Although the 35 in 1 Deluxe Digital Labincludes a simple logic probe section built on the breadboard,you may wish to purchase the very inexpensive Chaney C6722CMOS/TTL Logic Probe Kit. Although this is totally optional youwill find that this logic probe is very useful to test and troubleshootall kinds of digital circuits. (See Page 49).16Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

33 in 1Electronic Exploration LabNo Soldering Required& ReusableThis exciting breadboard lab requiresno soldering or previous electronicexperience. The lab enables anystudent to build 33 different electronicexperiments and activities. It’s applicablefor use in elementary grades up throughcollege and is safe to use. The lab ismeant to be used over and over againto save money. Not only is this lab complete with everythingthe student needs, but also the instruction booklet is designedso that the teacher does not need to be involved (unless heor she desires to be).The student builds and studies the first 11 instructionalcircuits which include theory and data facts along with a simplepencil activity quiz. The remaining 22 experiments for thestudent are fun to build electronic circuits that have a partslist, schematic and parts placement drawing. These give thestudent an ample introduction to electronic components andcircuitry.Breadboard type kits have been around for years, however,this lab is the first to incorporate an introduction to Ohm’s law,electromagnet circuitry, motor circuitry, transistor circuitry, ICcircuitry and 7 segment display circuitry all in one lab. There isnow no need to have several different breadboard kits to learnbasic electronic concepts. One lab covers almost all aspectsof basic electronic concepts and components.Not only does our 33 in 1 Deluxe Electronic ExplorationLab introduce various electronic educational concepts butit is also a fun and interesting motivational activity for yourstudent. Complete with all electronic parts, breadboard andinstruction booklet. Requires one 9V battery (not included).If the student has already built the 33 in 1 Deluxe ElectronicExploration Lab, you may wish to purchase our 35 in 1 DeluxeDigital Lab Exploration Kit shown on the previous page so thatthe student can gain digital electronics fundamentals.C6709 $26.95Learn Electronics with our 33 in 1Deluxe Electronic Exploration Lab!33 in 1 Electronic Exploration Lab Manual Contents:Instructional Experiments1 Experiment 1 Resistor Color Code2 Experiment 2 Ohm’s Law and The Basic Electronic Circuit3 Experiment 3 Parallel Circuit with Lamp4 Experiment 4 Diode Action5 Experiment 5 Light Emitting Diodes6 Experiment 6 Electromagnetism7 Experiment 7 Capacitance8 Experiment 8 Transistor Switch9 Experiment 9 Variable Resistor LED Dimmer10 Experiment 10 DC Motor Experiment11 Experiment 11 Transistor OscillatorElectronic Construction Activities12 Activity 12 7 Segment Display Circuit13 Activity 13 SCR Latching Switch14 Activity 14 Conductor Identifier15 Activity 15 2 Transistor Audio Oscillator16 Activity 16 Continuity Tester17 Activity 17 Multivibrator LED Blinker18 Activity 18 Insanity Alarm19 Activity 19 Light Controlled Bird20 Activity 20 Code Practice Oscillator21 Activity 21 Magic LED Light22 Activity 22 Water Alarm23 Activity 23 Ticking Clock Sound24 Activity 24 Phasor Ray Sound Generator25 Activity 25 Emergency Siren26 Activity 26 Adjustable Blinking Light and Sound27 Activity 27 Timer with LED28 Activity 28 Electronic Motor Speed Control29 Activity 29 IC LED Flasher30 Activity 30 IC Adjustable Frequency Sound Generator31 Activity 31 IC Light Activated Wake Up Alarm32 Activity 32 IC 2 Color LED Flasher33 Activity 33 IC Burglar Alarm33 in 1 ELECTRONIC EXPLORATION LABChaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 17

SOLAR EXPLORATION LAB10 in 1Solar Energy Exploration LabOur re-usable Solar Energy Exploration Lab requiresno soldering or previous electronic experience. The labenables any student to experiment with free electricity generatedfrom the sun. Its applicable for use in elementary grades upthrough college and is safe and easy to use. The lab is meant to beused over and over again to save money. The lab is complete withinstruction booklet and is designed so that the teacher does not needto be involved (unless he or she desires to be). Utilizes a quality universalplug-in breadboard with high quality powerful solar panel, resistors, diode, motor with prop, electronicbuzzer, flashing LED, super capacitor and wires. There’s nothing extra that you’ll need to use this laband unlike other solar labs on the market, you will get more value from our product as it has many experimentsthat are unique to our 10 in 1 Solar Exploration Lab. Of course, you’ll get a prop experiment plus 9 more fun and educationalexperiments to challenge you students. In addition you will receive detailed descriptions of the concepts that each experiment covers.In all you will find that the added detail and additional experiments that The 10 in 1 offers make it a superior product more suitable foruse in educating your students. We know you will like our Solar Energy Exploration Lab and will want to have one for everyone in yourclass. Listed below are the main experiments/activities that the student will perform.No Soldering Required& Reusable10 in 1 Deluxe Solar Energy Exploration Lab Manual Contents:Instructional Lessons & Experiments1 Experiment 1 Introduction to Solar Cells2 Experiment 2 Solar Panels3 Experiment 3 Diode Action4 Experiment 4 Solar Powered DC Motor5 Experiment 5 Resistors & Color Code6 Experiment 6 Solar Powered Alarm7 Experiment 7 Solar Power Storage8 Experiment 8 Solar Powered Flashing Light9 Experiment 9 Solar Pulsating Alarm10 Experiment 10 Another Environmentally Safe Method of Generating PowerThis Lab comes with a special glass Solar Panelthat produces a useful amount of voltage andcurrent so that it can be used to perform yourown experiments!Introduce your studentsto SOLAR ENERGYwith our 10 in 1Solar Exploration Lab!C6853 $30.9518Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Solar Science WorkshopsSolar Powered Boat ActivitySolar Powered Boat ActivityPower from the sun can be harnessed in many different ways. This clean, environmentally safe form of energy is readilyavailable and is being used to heat water, heat buildings, cook food, provide electricity and many other applications aswell.The Solar Powered Boat Kit uses a high current silicon solar cell to directly power a small electric motor. The shaft of themotor will turn a small plastic propeller when the sun strikes the solar cell. When connected with the correct polarity, thepropeller will produce a force of wind which will push the small balsa wood boat forward.This kit also contains parts and instructions for several scientific experiments. All of the experiments are designed to givea basic understanding of solar cells, magnetism, compass operation, electric DC motors and method of propulsion. Onlysimple hand tools, sandpaper, white glue and tape are required, but not included. In addition, you may wish to customizeand paint your boat. Paint is not included. No batteries and no soldering is required.Our Solar Powered Boat Activitymakes a fun introduction toSolar Energy!andWith No Soldering this activity isideal for all grade levels!Solar Powered Boat Manual Contents:Instructional Lessons & ExperimentsSolar Cell Introduction and Brief History1 Experiment 1 Compass Function2 Experiment 2 Permanent Magnet Function3 Experiment 3 Identifying Solar Cell Polarity4 Experiment 4 DC Motor Function5 Experiment 5 Fan Function6 Experiment 6 Boat PropulsionBoat ConstructionC6983 $24.95Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 19

34 in 1 ROBOTICS LAB34 in 1Deluxe ExplorationROBOTICS LABIntroduce your students to the fundamentals of robotics technologywhile building 28 different robots in one. The student starts by buildinga simple robot, and then disassembles it to progress to building morecomplex designs which are remote controlled with IR (infrared) visionand object avoidance. This lab is totally reusable and will stimulatethe student’s minds in robotic technology.Try it! You will love it!Lab Includes:• High Quality Breadboard• 3 Wheels, 2 Motors, 2 Belts,and Various Mechanical Parts• Attractive Smoked Plexiglass Base• All Necessary Electronic Parts• Fully Illustrated Instructional Manual• Relay Board (requires soldering)Super Value& Reusable!Each experiment is designed to progressin an easy-to-follow and logical manner.Each one explores both meaningfuland interesting topics!Experiment 13: The IR-Eye Robot(Assembled)LEARN ABOUT:Robot Motor Tractionand Power SystemRobotic MotionTime Controlled MotionRemote Controlled MotionRobotic Vision (CDS & Infrared)Sound Detection & Control... and many more topics.BUILD THE FOLLOWING ROBOTS:Explorer I and IIThe UnstoppableThe Independent Minded RobotThe Night RunnerThe Day RunnerThe IR (eye) RobotObedient I (Remote Controlled Robot)Obedient II (Remote Controlled Robot)Robot PetObstacle Avoiding Robot IObstacle Avoiding Robot IIBig Ears RobotThe Music Dancer Robot... and many more.C6762 $71.0034 in 1 Deluxe Exploration Robotics Lab Manual Contents:Instructional Lessons & Experiments1 Lesson 1 Introduction to Robotics2 Inventory & Parts Identification3 Lesson 2 The Chaney Robotics Lab4 Experiment 1 Assembling and Testing the Robot Motor System5 Experiment 2 Assembling the Robot Base and Power System6 Experiment 3 Assembling and Testing the Relay Control Board7 Experiment 4 Robot Forward Motion8 Experiment 5 Robot Backward Motion9 Experiment 6 Robot Forward Right Turn10 Experiment 7 Robot Backward Right Turn11 Experiment 8 Robot Hard Right Turn12 Experiment 9 Robot Forward Left Turn13 Experiment 10 Robot Backward Left Turn14 Experiment 11 Robot Hard Left Turn15 Experiment 12 Time Controlled Motion I16 Experiment 13 Time Controlled Motion II17 Experiment 14 Time Controlled Hard Right Turn18 Experiment 15 Time Controlled Hard Left Turn19 Experiment 16 Explorer I Robot20 Experiment 17 Explorer II Robot21 Experiment 18 The Unstoppable Robot22 Experiment 19 The Independent Minded Robot23 Experiment 20 The Night Runner Robot24 Experiment 21 The Day Runner Robot25 Experiment 22 Infrared (IR) Vision26 Experiment 23 The IR-Eye Robot27 Experiment 24 Obedient I: IR Remote Controlled Robot28 Experiment 25 Obedient II: IR Remote Controlled Robot29 Experiment 26 Robot Pet30 Experiment 27 IR Obstacle Avoiding Robot I31 Experiment 28 IR Obstacle Avoiding Robot II32 Experiment 29 Sound Detection (Robot Ears)33 Experiment 30 Big Ears Robot34 Experiment 31 The Music-Dancer Robot20Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Intro to SMTSurface Mount Technology LabChaney Electronics would like to introduce you to the tiny world of SMTThis Chaney Training Lab will introduce your students to the latestassembly technology known as “Surface Mount Technology”.Surface mount technology uses tiny leadless components, knownas surface mount devices (SMDs) which are quickly replacingstandard electronic components. Currently most electronicequipment incorporates this exciting new technology.By completing this lab, the student learns concepts about surfacemount technology (SMT) such as: the different types of surfacemounts devices (SMDs), the various types of surface mountassemblies, the automated soldering methods, and all of thestages of the manual and automated assembly processes ofsurface mount circuits. The student gains experience identifying,soldering and using surface mount devices by physically buildingan actual working surface mount technology project.This lab is the perfect introduction to SMT and does not requireany previous knowledge of this topic. It was designed so thatthe teacher does not need to be involved (unless he or shedesires to be). The lab is self-contained and reusable with theexception of the SMT project kit: “Deluxe SMD Learn to SolderKit” (Stock # C6719) which may also be purchased separately.A small soldering iron with a fine point and some solder is allthat is required to build the included kit.Lab Includes:• Fully Illustrated Instructional Manual• All Necessary Electronic Parts• Extra Practice and IdentificationComponents• Magnifier with TweezersSurface MountTechnology is Here!IDENTIFICATION COMPONENTSSMD COMPONENTSINTRO TO SMT LABIntro to SMTSurface Mount Technology LabPerfect introduction forstudents to learn oneof the latest componenttechnologies!magnifierwith tweezersC6725 $23.95DELUXE SMD LEARN TO SOLDER KITChaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 21

MAGNETISM EXPLORATION LAB25 in 1Deluxe Magnetism, Motors and DC Circuits Exploration LabThis fun, interesting and reusable Exploration Lab is perfect for any beginning student in Science,Electricity/Electronics, or Physics.Not only does this lab introduce students to important concepts in magnetism, but also it introducesthem to resistance, capacitance, diode action, LEDs, electromagnets, motors, switch operation, colorcode for resistors, series/parallel25 in 1 Deluxe Magnetism Exploration Lab Manual Contents:circuits, basic Ohm’s Law, currentInstructional Lessons & Experimentsflow measurement and even electricitygeneration.1 Experiment 1 Permanent MagnetsThis breadboard lab requires no soldering and is battery 2 Experiment 2 Electromagnetsoperated for safety. This lab doesn’t require any previous experience 3 Experiment 3 Compass Operationor knowledge. The instructor does not need to be involved if he or 4 Experiment 4 Galvanometershe chooses not to and the lab will amaze and provide interesting 5 Experiment 5 The Basic Electrical Circuitexperiments to motivate your students. This lab can be used over and 6 Experiment 6 Resistors / Color Codeover again so it is very economical.7 Experiment 7 Light a LEDThe 25 in 1 Deluxe Magnetic Lab covers some of the same8 Experiment 8 The Diodeconcepts that are presented in our 33 in 1 Electronic Exploration Lab,9 Experiment 9 Series Circuitshowever the 33 in 1 moves onto electronic concepts whereas this lab10 Experiment 10 Parallel Circuitsconcentrates on electricity and magnetism concepts and goes intomore depth in these areas. It’s best to have the students complete 11 Experiment 11 Series / Parallel Circuitsthe 25 in 1 Deluxe Magnetism Lab first and then move on to the 33 12 Experiment 12 Current Flow in Circuitsin 1 Deluxe Electronic Exploration Lab if possible, although each lab 13 Experiment 13 Ohm’s Lawcan be used alone and neither lab requires any previous knowledge 14 Experiment 14 Switch Actionof electricity!15 Experiment 15 Make a Simple MotorThe Deluxe Magnetism Lab Instruction Manual features 25 16 Experiment 16 Practical Motorexciting and fun to build learning experiments. Each experiment has 17 Experiment 17 Complex Circuitan explanation, a hands on lab that the student completes and a18 Experiment 18 Insulator or Conductorshort quiz to help with the learning experience and reinforce important19 Experiment 19 Flashing LEDsconcepts.20 Experiment 20 The CapacitorPlease look at the list of experiments on the right and you’lldiscover that the 25 in 1 Deluxe Magnetism, Motors and DC Circuits 21 Experiment 21 Electronic Coin FlipperExploration Lab is the best introduction to electricity and magnetism, 22 Experiment 22 Swinging Compassat an affordable price on the market today. Complete with all parts, 23 Experiment 23 Stop/Go Motor with Indicatorsuniversal breadboard and comprehensive Lab Manual. Requires 4 24 Experiment 24 Small Electricity Generator“C” batteries (not included). Skill Level 1.25 Experiment 25 Storage and Use of ElectricityRequires No Soldering & Can Be Used Over and OverA Tremendous Educational Value!25Reusable ExperimentsC6819 $21.9522Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

R.O.H.S. Expression Flashers100% Lead Free!Our new expression flashers are not only fun and colorful, they’re LEAD FREE!This R.O.H.S. series offers eight different and exciting label-based project kits. Each project kit features a custom designed full color labeland a bright flashing LED. These are a perfect introduction to basic electronic circuit theory and transistor function. Using two transistorcircuitry powered by one 9V battery (not included) each kit provides hours of blinking amusement. Size of PC board 3 1 /4” x 4 3 /4”.Complete with all parts, PC board, color label and instructions. Each kit is sold separately. Skill level 1.Out of Sight Kit C6962C6962C6964C6966C6967Keep Out KitToo Hot KitAwesome Kitonly$ 5 50eachC6964C6966C6967ROHS Compliant KitsMagical LED Learn to Solder Robot KitPerfect for any age students,our new “Magical LED learnto solder robot kit” containsno lead or hazardouschemicals. All componentsin this kit meet strict R.O.H.S.Requirements.The “Magical LED learn tosolder robot kit” consists of2 circuit boards and variouselectronic parts that yousolder to the boards. You firstsolder the non-functionalcomponents to learn goodsoldering techniques,then you progress to thefunctional components.Simple to build and can be customized to makevariations. You can paint the boards before assembly,pose the arms, and change the top antenna, i.e. hairwire!In the center of the robots body is an LED thatmagically changes from Red to Green. The 3.5” tall by1” wide robot uses one 9V battery (not included) whichallows the robot to stand on its own. Complete with allPC boards, parts and instructions. Skill Level 1.R.O.H.S. Magical LED Learn to SolderRobot Kit C6959 $8.95Customizeable Colorful R.O.H.S.Blinker KitThis small easy to buildelectronic kit uses aspecial 2 transistormultivibrator circuitto alternately flashtwo brilliant clear lensLEDs. To make thiskit customizeable wegive you 1 red LED,1 green LED, and 1yellow LED so that you can make the color combinationof your choice. Simply pick the combination of 2 LEDsthat you want! Operates from one 9V battery (notincluded). Size of PC board 1 1/4” x 1 3/8”. Completewith all parts (including the 3 brilliant color LEDs), PCboard and instructions. Skill Level 1.Customizeable Colorful R.O.H.S.Blinker Kit C6970 $4.25Handy R.O.H.S. SolderThis specially formulated rosin core soldercontains no lead and meets R.O.H.S.requirements. This solder is perfect foruse in building any of the R.O.H.S. kitson this page. You get a 6ft coil (amplesupply to build several kits).C7329 $2.00R.O.H.S. ApprovedSoldering IronC6652 $4.50Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 23

Microcontroller kitsSure to be a Sold Out show! Jam Man and band are coming to rock your town.Uses a preprogrammed PIC16F88 microcontroller and a sensitive IC amplifierwith an electret microphone to drive a 5X7 green LED matrix display. Jam Manis happy and sings along to the music. When its quiet for awhile heStock#C6987$25.95Stock#C7029$16.95Now TouringThe Jam Mantakes 5 (frowns and then goes to sleep) until he hears soundagain, then he gets back on stage! Operates on one 9V battery(not included). Size of PC board 2.8” X 1.25”. Complete with allparts, PC board and instructions. Requires soldering.Skill Level 2.(Demonstration Video Online!)POV KitCreate words that appear in mid air from 7 bright LEDsas the kit is waved. The POV kit uses a microcontrollerthat is easy to program with a simple built in pushbuttonswitch. Complete with all parts, programmed PIC16F88,PC board, and instructions. Operates from a 9V battery(not included). Requires soldering. Skill level 2.(Demonstration Video Online!)Learn to Solder KitsRobot spinswhen activatedRotating POVStock#C7030 Message KitCreate words that appear in a circle in mid$22.95 air. This kit is similar to our C7029 POV kit,however you don’t wave it -just turn it on and thewords appear in a circle. Uses a microcontrollerthat is easy to program with a simple built in pushbuttonswitch. Complete with all parts, programmed PIC16F88,motor, 2 PC boards, instructions, and 6” x 8” attractivebase. Operates on two 9V batteries (not included).Skill level 2.Learn to Solder Temperamental Robot KitThe Learn to Solder Temperamental Robot Kit features a fun robot with attitude thatcomes to life when it gets hot. Just grasp the Temperamental Robot’s heat sensor withyour fingers. If you are “hot blooded” within a second or two 3 bright LEDs will light up,one will flash and the Robot will spin around. Temperamental Robot will cool down,then shut down after a few seconds and will wait for the next person to activate it. Ifyou are “cold blooded”, you can grasp the Robot’s sensor and nothing will happen!The kit features about 20 components you install to learn good soldering techniques.Once you have mastered soldering, you then install the working electronic circuitrycomponents. Operates from one 9V battery (not included). Size of PC board is 1.5”x 3.5”. Complete with all parts, motor, PC board and instructions. Skill Level 1.Learn to Solder Temperamental Robot Kit.................................C6928 $9.9524Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Insider Soldering Tips to get Great Results the First Time!Always use a soldering iron and solder that’s adequate forthe job at hand. For all Chaney Kits a 30 watt soldering iron isadequate, and high quality rosin core solder should be used.Never use acid code solder for Chaney kits.Always tin the tip of the soldering iron by thoroughly coatingit in solder, then wiping the tip clean on a damp sponge. Thisremoves built up flux and gives better heat conduction. This stepcan be very messy and will drop solder onto your work surface,so be sure to have a safe work area before tinning the tip.Learn to Solder Robot KitAlways heat the connecting point where the component andboard meet before applying solder. Never drip solder ontothe connection point as this will nearly always give a faultyconnection.Always inspect each solder connection after cooling. A singlefaulty connection can cause a variety of problems including:complete non-operation, improper function,component damage, and even fire.This unique flashing Robot will not only help you learn good soldering techniques but will also be the centerof attention wherever it is placed! The eye LEDs, center LED, and both hand LEDs flash brightly for weekscontinuously or for months when you turn it off at the end of the day. Consists of 2 circuit boards and variouselectronic parts that you solder to the boards. You first solder the non-functional components in to learn goodsoldering techniques, then you progress to the functional LEDs. Simple to build and can be customized tomake unlimited variations (you can paint the boards before assembly, pose the arms and eyes, change theappearance of the antenna, etc.)! The 3 1/2” tall x 7/8” wide Learn to Solder Robot uses one 9V battery (notincluded) which also allows it to stand on just about anything (keyboards, monitors, desks, books, etc.). Uniquedesign incorporates the battery into the robot. Simple to build! Skill Level 1.Learn to Solder Robot Kit....................................................................................C6845 $9.25LEARN TO SOLDER KITSLearn to Solder KitSpecial kit designed for the student who has not had any experience with soldering. This kit has 30components to solder in giving the student ample soldering experience. The first 20 componentsto be soldered are used to gain soldering experience, but the last 10 components, when solderedin, make up a bright red and yellow alternating LED flasher! The LED flasher portion is built afterthe student has soldered in the 20 practice components, which include: capacitors, a transistor,resistors, and an IC socket. When the student has completed this kit, he/she should have developedgood soldering techniques and has a functioning LED flasher to show for his/her efforts. This kitrequires one 9V battery (not included). Size of board: 4.75” x 3”. Complete with all parts (includingpractice parts for soldering) and complete soldering instructions. Skill Level 1.optional plastic Type 5 box C6367 $3.90Learn to Solder Kit.....................................................................C6445 $7.25Learn to Solder Rocket KitThis special kit is the perfect kit to introduce students to good soldering techniques. Whencompleted, the 4” tall rocket flashes 13 bright red LEDs and will stand upright on a desk or shelf.The student learns to solder by following the detailed instructions showing how to solder the 22practice components. These include cable, capacitors, diodes, resistors, and transistors. With theknowledge and skills obtained from soldering the practice components, the student then finishesthe rocket by installing the 13 bright LEDs that flash when a 9V battery is connected (battery notincluded). Size of rocket PC board is 4 3/8” tall x 1 1/4” wide. Complete with all parts, PC boardand instructions. Skill Level 1.Learn to Solder Rocket Kit.......................................................C6864 $9.25Universal Learn to Solder KitHere’s the perfect kit to give students experience in learning soldering techniques for both standardand SMD components. The student begins by soldering various standard lead components suchas transistors, capacitors and an IC socket. The student then progresses to SMD sections (on thereverse side of board) where the student practices soldering various SMD parts such as transistors,diodes, resistors, capacitors and an IC. Finally, the student builds a functional Insanity Alarm Kit(see description on page 35) which is constructed using both regular and SMD components sothat some parts are on each side of the board. The Insanity Alarm operates on one 9V battery (notincluded). Size of PC board: 2 1/2” sq. Kit is supplied with 33 parts, PC board and instructions.Skill Level 1. optional plastic Type 2 box C6364 $2.40Universal Learn to Solder Kit..................................................C6758 $7.25BackFrontChaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 25

INTRO TO KIT BUILDING PACKAGESComplete Introduction to Kit BuildingThis super package helps your student succeed in buildingelectronic kits because it contains everything your studentneeds to get started. This is an amazing value and it providesan easy way to get started in the “Fun of Kit Building”.C6898 $19.95Learn toSolder KitNon-functionalPC board andcomponents thatthe students build tolearn how to solder.“Blinder” LEDFlasher Kit(see C6891 on page 41of this catalog) Createsbrilliant flashes oforange/red light!C6891 kit requires one 9Vbattery to operate (not included).Contains everything neededfor the novice to start buildingkits right away: Tools, Solder,Kits & more!Deluxe Introduction to Kit BuildingLearn to Solder Kit:Non-functional PC board andcomponents that the students build tolearn how to solder.Electronic Cricket Kit:(see C6707 on page 50 of thiscatalog). This is a fully functional,one IC kit that the student builds afterhe/she learns how to solder.Learn to Solder Robot Kit:(see C6845 on page 25). Uniqueflashing Robot will not only help youlearn good soldering techniques butwill also be the center of attentionwherever it is placed!Kits (C6707 & C6845) require one 9V battery each to operate (not included).The Complete Introduction to Kit Building package contains:• Low wattage 120VAC soldering Iron• Tube of 63/37 rosin core solder for electronic kit building• Sharp wire cutting pliers• Special Soldering Helping Hands with adjustable board holder,magnifying glass, solder tip cleaner sponge and soldering ironholder• Pair of safety glasses• Learn to Solder Kit; Non-functional PC board and componentsthat the students build to learn how to solder.• “Blinder” LED Flasher Kit (see C6891 on page 41 of this catalog).This is a fully functional, one IC kit that the student builds afterhe/she learns how to solder.• Complete detailed instructionsThis super package helps your student succeed inbuilding electronic kits because it contains everythingyour student needs to get started. Amazingvalue containing three separate kits which are easyto build and fun to operate!C6933 $29.95Each DELUXE Introduction to Kit Building package includes:Detailed set of Instructions;Low wattage 120VAC SolderingIron; Tube of 63/37 RosinCore Solder (for electronickit building); Sharp Wire CuttingPliers; Special SolderingHelping Hands (with adjustableboard holder, magnifyingglass, solder tip cleanersponge and soldering ironholder); Pair of Safety Glasses.Kits included are the Learn to Solder Kit, the Electronic CricketKit (C6707) and the Learn to solder Robot Kit (C6845).Complete Introduction to SMD Kit BuildingThis super package helps your student succeed in buildingelectronic kits which incorporate Surface Mount Devices(SMD) because it contains everything your student needs toget started. This is an amazing value and it provides an easyway to get started in the “Fun of Kit Building”.C6932 $27.95Each Complete Introduction to SMD Kit Building package includes:Detailed set of Instructions; Low wattage 120VACSoldering Iron; Tube of 63/37 Rosin Core Solder (forelectronic kit building); Sharp Wire Cutting Pliers;Special Soldering Helping Hands (with adjustableboard holder, magnifying glass, solder tip cleanersponge and soldering iron holder); Pair of SafetyGlasses; Magnifier with Tweezers. Kits includedare the SMD Learn to Solder Kit (C6719) and theSMD IC Star Flasher Kit (C6708).SMD Learn to Solder Kit:(see C6719 on page 27 of thiscatalog) Student learns to solderSMD parts but in the end thestudent has an attractive andfunctional SMD dual color LEDflasher to show for his/her effort.Very nice introduction to soldering!SMD IC Star Flasher Kit(see C6708 on page 48 ofthis catalog). This is a fullyfunctional, one SMD IC kitthat the student builds afterhe/she learns how to solder.C6708 kit requires one 9V batteryto operate (not included).26Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Deluxe Learn to Solder KitThis special kit is similar to the regular “Learn To Solder Kit” shown on page 25, however, this kit has somevery unique features. Not only does it have a special non-functioning “Learn To Solder” section, it also hastwo additional kits on one circuit board. You get a bright yellow and red “Jewel” LED Flasher Kit and also anInsanity type Alarm Kit. The deluxe learn to solder kit uses a specially designed circuit board that allows youto build all three kits. After construction and testing, you simply snap the main circuit board into the 3 separateindividual kits.1. The Learn to Solder middle section is constructed first to give your student ample soldering experience.2. Next, the student constructs the Insanity type Alarm Kit section. This unique kit is equivalent in operation toour most popular selling Insanity Alarm Kit (see page 35). It emits a piercing tone when the lights go out, butstays perfectly silent when they turn on the lights to look for it.3. Finally, the student completes the more complicated “Jewel” LED Flasher Kit section. This IC circuit kitalternately flashes 4 bright red LEDs with one bright yellow LED.This unique kit is more challenging to build and is the perfect “wrap up”to test the students skill in making kits.Remember, you get all three kits listed with all parts and PC board. Requires two 9V batteries (not included), one for each functional kit. Overall size of circuitboard before snapping it apart is 5.5” x 1.75”. Order this unique kit now for a complete solution to your kit building needs! Skill Level 1.Deluxe Learn to Solder Kit..............................................................................................................................C6491 $10.00Deluxe SMD Learn to Solder KitHere’s the perfect way to gain experience in soldering, identification and use of Surface Mount Device (SMD)technology. This kit features 32 SMD components, including 3 SMD 8 pin ICs, microprocessor IC, capacitors,resistors, transistors and a LED. The first 24 components are parts used to gain ample soldering experiencewith SMD parts as the student solders the various parts onto the practice section of the PC board. The last 8SMD components are used to make an IC type dual LED flasher. This section of the kit flashes a dual colorSMD LED. It flashes red then green from the same LED. Not only does the student learn to solder SMDparts but in the end the student has an attractive and functional SMD dual color LED flasher to show forhis/her effort. Operates on one 9V battery (not included). Size of PC board: 2” x 3”. Complete with all parts,PC board and instructions. A super value! Skill Level 2.optional plastic Type 2 box C6364 $2.40Deluxe SMD Learn to Solder Kit.........................................................C6719 $8.25Learn to Solder 9V Battery Tester KitThis is the perfect learn to solder kit! Not only does it give the first year student ample solderingexperience with 22 practice components, it allows the student to create a very useful 9VDCbattery analyzer/tester. Accurate and handy to have around, the tester lights up 2 LEDs toindicate whether the battery is in new/fresh condition, has some life left (about 7.5V to 8V) or isdead (under 7V). Size of PC board 1.9” x 3.4”. Complete with all parts (including practice partsfor soldering) and complete soldering instructions. Skill Level 1.optional plastic Type 2 box C6364 $2.40Learn to Solder 9V Battery Tester Kit.............................C6972 $9.00Racing Robot Learn to Solder KitThe Racing Robot Learn to Solder Kit features a three wheel motorized chassis and a colorfulrobot face that flashes on and off as the robot races out of control. Race this robot againstothers to see which robot is the fastest. Kit features 18 components that you install first tolearn good soldering techniques. Once you have mastered soldering you then install the oneIC circuitry, Face circuit, motor and mechanical assembly. Operates from one 9V battery (notincluded). Size of Face PC board about 1.5” x 2”. Size of main chassis PC board 2” x 4”.Complete with all parts, PC boards, motor and instructions. Skill Level 1.Racing Robot Learn to Solder Kit........................................................C6927 $12.95Electric Slider Learn to Solder RobotStand up Electric Slider Learn to Solder Robot, not only allows students to learngood soldering techniques, but also provides them with a bright colorful sliding,scooting robot. Operates on one 9V battery (not included) and uses 2 powerful motorsand a one IC circuit to move in a weird pattern on any smooth surface. Featurescolorful flashing LEDs which make this kit a real attention getting project. Overallsize of PC board is 1.8” x 4”. Complete with all parts, PC board and instructions.Skill level 1.Electric Slider Learn to Solder Robot.................................................C7012 $9.95optional plastic Type 2 box C6364 $2.40 (requires two boxes)LEARN TO SOLDER KITS Robot KitsChaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 27

Robot KitsOne of ourmost popularkits!Light Spider Robot KitThis amazing robot uses its electronic brain to follow or find a light source (such as astandard flashlight). Using its drive motors, the Light Spider will scoot across any smoothhard surface (such as a linoleum floor or a wooden table top) looking for light. Whilesearching, a LED array on the front of the robot lights up and blinks. You will be amazedat the Light Spider’s ability to follow light. Operates from one 9V battery (not included)and uses a transistor brain to control its 2 motors. The PC board and motors can becustomized by painting them before assembly. Size of PC board is approximately 3.75”x 2.5”. Comes complete with all parts, PC board & instructions. Skill Level 2.Light Spider Robot Kit..................................................................C6886 $12.25Mini Light Spider Robot KitJust like our full size Light Spider Robot Kit, our Mini Light Spider Robot Kit uses itselectronic brain to follow the light from a standard flashlight. The Mini Light Spider willscoot across any smooth hard surface (such as linoleum, wood or other smooth hardsurface). We have sold thousands of the full size Light Spider Kits and we know you’llalso have fun with this mini version of it! The Mini Light Spider PC board is only 3” Lx 1.6”. It uses two tiny motors and operates from a built in 3.6V rechargeable battery(battery and charger are included so there are no batteries to buy!). Complete with allparts, PC board, battery, battery charger and instructions. Skill Level 2.Mini Light Spider Robot Kit..............................................................C6920 $12.95Alien Warbot Robot KitActivated by IR energy, this kit remains motionless until it detects IR energy. It will cometo life when you press random buttons on any TV/DVD remote or by our IR ActivatorRobot Kit (sold below). When activated, it vibrates/scoots on any smooth surface andalso flashes 7 bright LEDs while emitting a pulsating low frequency “vibrating” sound.Movement stops as soon as the source of IR energy stops. Operates from one 9Vbattery (not included) and features two special IR sensors, a special vibrating motor,sensitivity control and transistorized circuit. Round PC board is 2 3/4” in Dia. and canbe customized by painting it with your paint before you solder it (if desired). Completewith all parts, PC board and instructions. Skill Level 2.Alien Warbot Robot Kit...........................................................C6870 $15.25IR Activator Robot KitOur special IR Activator Kit vibrates and scoots while flashing 1 red LED and 6 IR LEDs. Ifplaced near an Alien Warbot, the IR Activator Robot will cause the Warbot to immediatelycome to life and either move towards it to attack or away from it to run! This kit is not activatedby IR energy, in fact its job is to produce crystal controlled IR energy to activate IRsensitive robots. Operates from one 9V battery (not included). PC board is 2 3/4” Dia. andcan be customized by painting it with your paint before you solder it (if desired). Completewith all parts, PC board and instructions. Skill Level 2.IR Activator Robot Kit....................................................................C6871 $16.25Classroom Alien Warbot Combination PackageHere’s a great way to save money and give students the exciting kits they want tobuild. This package includes 7 Alien Warbot Robot kits for the students to build,plus a free IR Activator Robot kit for the teacher to build. The Alien Warbot kits afterassembly can be placed in a grouping on a large table or smooth floor. When theteachers IR Activator Robot is placed in the center of the group, the Alien Warbotsactivate and go crazy trying to avoid it. It’s amazing to watch them scoot, spin,backup, etc. See above for detailed descriptions of the robots. Remember, you get7 Alien Warbot Kits and 1 IR Activator Kit as described above (This is a $120.00value!). Skill Level 2.Classroom Alien Warbot Combination Package...................C6865 $107.0028Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Peanut Mover Robot KitThis slow speed robot moves in a zig-zag pattern and can detect Styrofoam peanuts.The Peanut Mover will stop when it detects a peanut and then sound a shrillalarm. You can also configure the Peanut Mover Robot to push a peanut alongthe floor until a wall or other obstacle is reached. At the wall it will stop and soundits alarm. Have races against other Peanut Mover robots! Fun to build and operate.Works best in low light conditions on smooth surfaces. Features 2 motors,flashing LEDs, front brush, a 6 transistor circuit. Size of PC board is 5.2” x 2.4”.Operates on a 9V battery (not included). Complete with all parts, PC board andinstructions. Skill Level 2.Peanut Mover Robot Kit..........................................................C6914 $14.95Robot Kits“Speedster 500” Robot KitThis quick and zippy little robot zooms and turns along smooth hard surfaceswhile flashing its colorful “headlights”. The “Speedster 500” robot operates fromtwo tiny electronic brains that consist of flashing rainbow LEDs. Each time one ofthe LEDs flash, it causes the robot to turn in a different direction. Operates fromone 9V battery (not included). Size of board is 2.7” x 2”. Complete with all parts.Requires soldering. Skill Level 1. This robot is also available fully assembled (9Vbattery not included).“Speedster 500” Robot Kit..........................................................C7048 $13.95Also Available Fully Assembled.......................................C7048ASB $19.95Chrome Dome Line Tracing Robot KitChrome Dome is a fascinating robot! It can follow a black line (use black tape or a blackmarker) on a light surface. Not only does it reliably follow the unique “line track” thatyou lay out for it but it also does it with style. Features colorful brilliant blue and yellowLEDs that flash back and forth as each motor is activated. Uses only one 9V battery forpower (not included) and is about 3” square excluding the “Chrome Dome” top. Thisrobot features 4 separate adjustable controls to allow fine tuning of “Chrome Dome’s”line tracing abilities. Fascinating to watch, fun to build and operate. Complete with allparts, PC Board, Chrome Dome and Instructions. Skill Level 2.Chrome Dome Line Tracing Robot Kit..................................C6900 $24.95Special “Chrome Dome” Classroom PackageOrder this package of 10 “Chrome Dome” Robots at a discount and receive oneroll of 1/2” wide 100ft. long black electrical tape for free to use in making your linetrack. You get a package of 10 plus a free roll of tape for the price shown. This a$251.50 Value!Special “Chrome Dome” Classroom Package....................C6901 $240.00The Unstoppable Bug Robot KitThe Unstoppable Bug Robot (TUBR) is really a bug with an attitude andan electronic brain. It just can’t be stopped! If you put a box, object, or ifthere is a wall in front of the bug it has a powerful infrared detecting systemthat “senses” the obstacle and causes its simple brain to change direction.Features 2 motors, a bright red eye, a transistor/relay brain and 2 built inrechargeable batteries. Black plastic bug body is about 3 3/4” L x 1” W (excludingarms which have small motors attached). Operates on any smoothsurface such as a table, floor, desk, etc., when quick charged from a 9Vbattery (not included). Complete with all parts, PC board, bug body, motorsand instructions. Skill Level 2.The Unstoppable Bug Robot Kit.............................................C6902 $18.95Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 29

Robot KitsIR Vision Rover Robot KitThis incredible robot can actually see! As it explores, it emits invisible beams of IR (infrared)light which reflects off any obstacles in its path, including walls, rocks, humans, boxes,etc. Its simple brain and sensor causes the IR Vision Rover Robot to turn backwardsand then go forward in a different direction avoiding the obstacle it has detected up toone foot away. It can even be remotely controlled from up to 25 feet away by using anystandard DVD/TV IR remote control that you have. Simply point and press almost anybutton on your remote and you will notice that your IR Vision Rover Robot will immediatelyback up and then go forward in a different direction. The Rover emits beeps and blinksbright colorful LEDs as it explores. Operates from only two AA batteries (not included).Features DC-DC converter circuitry, sensitive IR sensor module, 2 IR LEDs, 9 colorfulLEDs, 2 powerful motors and reliable drive train. It’s a fun kit to build, and an excellentintroduction to robotics for your student. Size about 5 1/2” x 6 1/2”. Works on any smoothhard surface. Complete with all parts, PC board and instructions. Skill Level 2.IR Vision Rover Robot Kit.......................................................C6761 $35.95Little Jitterbug Robot KitBetter not leave any popcorn or chips around! This little jitterbug robot is waiting fornight, or when it’s completely dark, to roam the countertops in search of goodies.The light sensor allows the jitterbug to come alive and scoot around with the help ofa tiny vibrating motor. Customize its antennas and legs. Flashing LED allows you tofind this little critter. Operates on a 3V coin battery (included). Size of PC board 1.8”X .9”. Complete with parts, battery, PC board and instructions. Soldering required.Skill Level 1. One of the most reasonably priced robots available anywhere!Little Jitterbug Robot Kit............................................................................C6984 $5.95Aqualocator Robot KitHere’s an exciting colorful addition to our robot line. The Aqualocator Robotconstantly spins, scoots twirls or glides as it searches for water or soda popthat may have been “spilled” on a floor. As soon as it finds a “puddle” the brightred LED ring on top made up of 12 LEDs shuts off, its 3 powerful motors shutdown and a group of 4 bright green LEDs light up showing that the robot hasindeed found a water spill! Works on any smooth floor or surface (no carpetor pavement). Operates from one 9V battery (not included). Uses 2 PC boardsand 3 motors. Top PC board can be customized by painting before assembly (ifyou desire). Size of PC boards: 2.9” dia. Complete with all parts, 2 PC boardsand instructions. Skill Level 2.Aqualocator Robot Kit.....................................................................C6883 $24.95Gear Motor for RobotsGear motor assembly featuressee through yellow plastichousing which is about 2.7”long x 1.17” wide x 1.4” thick.Operates from 1.5VDC up to6VDC. Has 4 gears that makeup the assembly and a 0.9”long metal hex standoff with aremovable 2-59 screw. Great forexperimenting/creating robots.Note: this does not come with any instructions or other parts andthe output is not precision (slight wobble).C8601 $7.95Bag of Gears and SprocketsExperimenters bagof various gears andsprockets. Great forexperimenting withrobotics, this assortmentcontains variousplastic and metalgears from small tolarge with variouspitches, shapes, and teeth. Some may haveunusual shapes. Sorry no instructions or datais available for these.C8602 $14.9530Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Deluxe Blacklight in a Case KitThis is the ultimate blacklight for hundreds of applications such as lighting blacklight posters,detecting invisible UV inks, lighting certain fluorescent minerals, lighting glow in the dark stars,etc. This deluxe blacklight kit features a sturdy and handsome gray custom case, a concentratingreflector, a long life 5 1/4” filtered blacklight tube, an adapter, and a 3” x 1 3/4” PC board. Thecircuitry uses an IC and a high power darlington transistor. An AC adapter is included so thatthe blacklight can be operated from standard 120 VAC. Size of case is about 7” x 3 1/4” x 2 1/4”.For portable operation at night the kit can operate from 4 “C” cells (not included). Completewith all parts, tube, custom gray case, adapter, PC board and instructions. Skill Level 2.Deluxe Blacklight in a Case Kit...............................................C6786 $23.45Battery Operated Blacklight KitHere’s an unusual kit that is just the thing for finding fluorescent minerals, detecting insectsthat glow under black lights, reading invisible fluorescent inks, etc. Completely portablekit comes with an unfiltered large U shaped black light tube and efficient solid state drivecircuitry. Features control to vary the brightness and lightweight portable design. Sizeof board: 7” x 1.8”. Operates from 6VDC (battery not included). Complete with all parts,PC board and instructions. Skill Level 1.optional Type “B” mounting base C6622 $2.25Battery Operated Blacklight Kit..............................................C6889 $11.25Portable Filtered Blacklight KitThis kit features a high output 5 1/4” long filtered ultraviolet longwave blacklight tube. Light upposters, invisible inks, many minerals, glow in the dark stars, products, etc. Completely portable asit operates on either a 6V lantern battery or 4 “D” cell batteries (Batteries and battery holders notincluded). The output is filtered and it emits very little regular light spectrum. The deep purple glowcan even be used to find certain insects, which glow brightly under UV light. Size of PC board: 513/16” x 2 3/8”. Complete with all parts, PC board, tube and instructions. Skill Level 2.optional Type “B” mounting base C6622 $2.25extra 5 1/4’’ long filtered UV tube C6527 $5.95Portable Filtered Blacklight Kit...............................................C6790 $17.45Unfiltered Blacklight Strobe KitLight up blacklight inks and posters with this unique Unfiltered Blacklight Strobe Kit (greatfor Halloween effects). Uses 3 large (10mm) UV LEDs that flash at a rate adjustable fromabout 80 up to 300 flashes per minute. In a darkened room the output is amazing. Operatesfrom one 9V battery (not included) and features an IC circuit with “on board” adjustablespeed control. Size of PC board 3 3/8” x 2 1/4”. Complete with all parts, PC board andinstructions. Skill Level 2.optional plastic Type 2 box C6364 $2.40Unfiltered Blacklight Strobe Kit..........................C6973 $10.958 Note Tunable Electronic Organ KitTunable 8 note organ features IC oscillator and darlington transistor output stage to provideclear loud tones. Play simple compositions, favorite tunes, etc. Uses reliable push-buttonswitches for continuous trouble-free performance. Each note is fully tunable with on boardtrimmer controls. Operates from 3V to 9VDC. Size of board: 2” x 5”. Complete with all parts,PC board and instructions. Skill Level 1.optional plastic Type 5 box C6367 $3.908 Note Tunable Electronic Organ Kit.....................................................C4736 $10.25Light Sensitive Sound Generator KitSimple to build kit creates a tone which varies depending on the amount of light you allowto strike on a CDS cell. Kit features IC circuitry and small speaker to create this unusualeffect. In total darkness the unit emits clicks or is silent; as light increases the kit emitsclicking sounds then with more light a continuous tone. Operates from 9V battery (notincluded). Size of board: 1 1/4” x 1”. Complete with all parts, PC board and instructions.Skill Level 1.optional plastic Type 2 box C6364 $2.40Light Sensitive Sound Generator Kit...................................................C4164 $5.25BLACK LIGHT & PARTY KITS SOUND EFFECTS KITSChaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 31

SOUND EFFECTS KITSCOLOR ORGAN KITSChirp Chirp KitWhen you are in the mood for some disturbing, irritating chirping sounds, this kit will meet yourneeds. Not only does it produce a sharp chirping racket but it also flashes a bright LED alongwith the noise. Operates on one 9V battery (not included). Size of PC board 2” x 1.25”. Completewith all parts, PC board and instruction. Skill Level 1.optional plastic Type 1 box C6363 $1.80Chirp Chirp Kit.............................................................................C6878 $4.2510 Note Sound Synthesizer KitVery unique synthesizer features 10 adjustable notes, variable pitch, variable speed, flashingLED and individual or flowing notes. Make “robot” sounds, space war, computer effects,etc. One our most unusual kits! Circuit features three ICs and 12 trimmer resistors. Size ofboard: 2 13/16” x 4”. Operates from one 9V battery (not included). Complete with all parts,PC board and instructions. Skill Level 2.optional plastic Type 5 box C6367 $3.9010 Note Sound Synthesizer Kit...............................................C4722 $12.25Sci-Fi Sound Effects “Theremin”Produce all kinds of weird sound effects with this small simple to build kit. Utilize 2 light sensors: onecontrols the frequency and the other modulates (varies) the sound. Simple one IC circuit with builtin speaker and an RCA jack so you can send the sound to your amplifier if desired. Simply use yourhands to produce some of the strangest, spookiest sounds you’ll ever want to hear! Operates fromone 9V battery (not included). Size of PC board 3 1/2” x 1 1/4”. Complete with all parts, PC boardand instructions. Skill level 1.optional plastic Type 5 box C6367 $3.90Sci-Fi Sound Effects “Theremin”...........................................C6841 $9.25120VAC Single Channel Color Organ KitSimple to build kit uses a transformer and SCR circuit to flash lamps of your choice (up to 200 watts)to the beat of the music. Simply connect input of the color organ to your stereo speaker and watchthe display. Features level control and one AC outlet to connect Christmas lights, lamp, etc. Operatesfrom standard 120VAC. Size of board: 2” x 1”. Complete with parts, PC board and instructions.Skill Level 2.optional plastic Type 2 box C6364 $2.40120VAC Single Channel Color Organ Kit.............................C4738 $6.75120VAC Sound Activated 3 Channel Color Organ KitThis exciting kit causes lights of your choice (up to 200 watts per channel/600 watts total) to flashto the beat and the frequency of the music without any connection to your amplifier, stereo, radio,etc. Simply plug in any lights of your choice to the 3 AC outlets provided. Features 3 separatefilters with each channel having its own “on board” response control so that you can adjust eachchannel for desired response. This deluxe kit has a speaker microphone driving a high gainIC/SCR circuit. Operates from standard 120VAC. Size of board: 6.2” x 3.4”. Complete with allparts, PC board and instructions. No case available. Skill Level 2.120VAC Sound Activated 3 Channel Color Organ Kit.......C6353 $20.50Our Most Sensitive Sound Activated 2 Ch Color Organ KitThis is our most sensitive sound activated 2 channel color organ kit. It uses a built in microphone and isperfect for use in haunted houses, Halloween displays, Christmas displays and more. Has two outlets toplug in any incandescent lamp (up to 200 Watts). Complete with PC board and all electronic parts, however,we do not have a case available. Operates on 120VAC. Requires soldering and you should have AC safetyknowledge before using. Size of PC board is 2.7” square. Skill level 2.optional plastic Type 5 box C6367 $3.90Our Most Sensitive Sound Activated 3 Channel Color Organ Kit....C7025 $17.95120VAC 3 Channel Color Organ KitVery popular 3 channel color organ causes lights of your choice (up to 200 watts per channel) to flashto the beat and frequency of the music. Simply connect the color organ to your stereo speaker. Hasinput transformer to isolate color organ from stereo and has 3 different signal filtering stages for low,medium and high notes. Kit features level control and 3 separate AC outlets to connect Christmaslights, lamps, etc. Operates from standard 120VAC. Size of board: 3” x 5”. Complete with all parts,PC board and instructions. Skill Level 2.optional plastic Type 5 box C6367 $3.90120VAC 3 Channel Color Organ Kit.......................................C4530 $12.2532Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Electro Spinner KitThis amazing kit features a brilliant neon like rainbow of spinning colors. The Electro SpinnerKit uses two special rainbow flashing LED’s, a motor and a special electronic circuit to produceattractive and stunning ever changing rings of neon like colors. The Electro Spinner automaticallyturns on when it is in the dark and spins for almost an hour before needing to be recharged. Kitincludes all parts, PC board, motor, rechargeable battery, charger and CD base. Overall size ofPC board is about 2” square. Skill Level 2.Electro Spinner Kit....................................................................................C6936 $14.95Exploding Star Color Organ KitThis spectacular color organ kit will amaze and thrill anyone who has the pleasure of seeing it in action.Very colorful, bright and highly animated exploding star effect is controlled by the beat of the music and a 2IC circuit. The display is like a firework that is in sync with your music. No connection to your sound sourceis necessary as it uses an ultra-sensitive electret microphone to pick up the sound. Kit uses blinding outputLEDS in red, green and yellow colors (25 total), 6 transistors and 2 ICs. Operates on one 9V battery (notincluded). Size of PC board is 5 1/16” x 3”. Complete with all parts, PC board and instructions. Be the firstin your class to own this amazing electronic display and everyone else will want to borrow it for their nextparty! Skill Level 3.Exploding Star Color Organ Kit........................................................C6818 $16.25Shimmering Color Organ KitExciting portable color organ provides a colorful display in response to music. Display shimmers andflashes to your music without any connections. The kit uses 6 jumbo red LEDs and 6 jumbo yellowLEDs with a sensitive amplifier IC. No connection to your stereo is needed as the Shimmering ColorOrgan Kit uses a crystal microphone to pick up the sounds of your music! Take your color organ withyou anywhere, as it requires only one 9V battery (not included) to operate. Size of board: 2 3/4” x 31/8”. Complete with all parts, PC board and instructions. Skill Level 2.optional plastic Type 4 box C6366 $3.60Shimmering Color Organ Kit...................................................C6446 $8.25Bright Star Color Organ KitThis small super sensitive color organ kit features 5 bright LEDs that flash to the beat of the music.Circuit features a miniature electret microphone and a high gain 3 transistor circuit so no connectionsto your stereo are needed! Simply place the kit in the general vicinity of your speakers, adjust thegain control and you are ready for bright Star flashes of light as your music plays. Operates on one9V battery (not included). Size of PC board is 1 13/16” square. Complete with all parts, PC boardand instructions. Skill Level 1.optional plastic Type 2 box C6364 $2.40Bright Star Color Organ Kit......................................................C6815 $6.75Binary Counter (Logic Basics) Kitoptional plastic Type 5 box C6367 $3.90One of the most basic building blocks of electronic computers is the binary number system. Thiskit counts in binary numbers and displays the binary number by red LEDs. A LED turned on is a 1and off is a 0. This kit provides an easy to understand display of the binary number. The counterincreases by 1 number each time the button is pushed. It also can count automatically by holdingthe button down. Teaches logic principles and binary counting. This kit features 7 red LEDs, countbutton, clear button and a 2 IC circuit. Counts from 0 up to 127 in binary numbers. Can be usedalone or can be connected to the Decimal Display Kit below which displays the decimal numberequivalent of the binary number. Operates from one 9V battery (not included). Size of circuit board:3.6” x 3”. Complete with all parts, PC board and instructions. Skill Level 3.optional plastic Type 5 box C6367 $3.90Binary Counter (Logic Basics) Kit.........................................C6359 $12.25COLOR ORGAN KITS COUNTER KITSDecimal Display KitThe Decimal Display Kit counts and displays decimal numbers from 0 to 99. Its primary function is tobe connected to the Binary Counter Kit above to display the decimal number equivalent of the binarynumber shown on the Binary Counter Kit. Can also be used in conjunction with several of our kits toprovide “next number to be served display”, people counter, lap timer, event counter, etc. FeaturesIC circuitry and two bright 7 segment LED displays. Operates from one 9V battery (not included).Size of board: 3” x 3.25”. Complete with all parts, PC board and instructions. Skill Level 3.optional plastic Type 5 box C6367 $3.90Decimal Display Kit....................................................................C6360 $13.25Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 33

ALARM KITSTemperature Warning KitThe Temperature Warning Kit can be set to indicate a rise or drop in temperature. You simply adjustthe control knob on the kit for the ambient control temperature that the thermistor is sensing. Now asthe temperature changes, a Red or Green LED indicates over or under temperature from the standard.Features an IC circuit and operation from one 9V battery (not included). Use this kit to warn of gardentemperatures below 32˚ or refrigerator/freezer temperatures above normal, etc. Order optional wire toallow for remote location of thermistor sensor if desired. Size of PC board 2” x 1.8”. Comes completewith all parts, PC board, 9” of wire, and instructions. Skill Level 1.optional Type 2 plastic box C6363 $1.80optional 200ft. of twisted pair wire for above C6579 $19.00Temperature Warning Kit..........................................................C6908 $5.25Plant Soil Monitor KitTime saving kit allows the user to determine if the plant soil needs more watering or is wetenough. Features IC circuitry and two bright LEDs. Green LED indicates ample moisture, redLED indicates more water is needed. Kit comes with simple moisture probe and has trimmercontrol to adjust kit to a “standard” of moisture content. Helps prevent over-watering or underwateringof plants, gardens, etc. Operates on 9V battery (not included). Size of board: 2” x 1.8”.Complete with all parts, PC board and instructions. Skill Level 1.optional Type 1 plastic box C6363 $1.80optional 200ft. of twisted pair wire for above C6579 $19.00Plant Soil Monitor Kit.................................................................C4744 $5.75Deluxe Burglar Alarm KitThis deluxe burglar alarm system is perfect for helping to protect houses, sheds, garages and evencars. Uses unique pressure sensitive switch that you make and then hide under throw rugs, carpets,car mats, etc. Very unique and has many features found on professional alarm systems:• Adjustable time out period • Pressure Sensitive Switch• Red LED arming indicator • Built in horn• Battery powered from 6VDC • Relay contacts for optional external equipmentComplete with all parts (except wire), PC board, pressure switch material and instructions. Operatesfrom one 6V lantern battery (not included). Size of PC board: 4” x 3.25”. Requires 2 conductor wirethat you must supply (to go from pressure switch to PC board) and masking tape. Skill Level 2.optional plastic Type 5 box C6367 $3.90Deluxe Burglar Alarm Kit..........................................................C6486 $10.25Professional Burglar Alarm KitThis useful kit includes all the features you would expect from a professional burglar alarm. It usesan IC circuit and has an exit time delay to allow you to leave your home before the unit is armed, anentrance delay to allow you to disarm the unit when you return home, an automatic horn cutoff aftera period of time, an automatic reset circuit, and of course, N.O. and N.C. loops to allow you to useyour choice of optional sensor switches, such as reed switches, snap action switches, etc. Operatesfrom two 9V batteries (not included). Comes with 9V horn alert, but if you wish, you can activate yourown horn alarm if you have one. Size of PC board: 3 1/4” x 2 5/8”. Complete with all parts (exceptsensor switches), PC board and instructions. Skill Level 2.Professional Burglar Alarm Kit...............................................C6785 $11.25The Magic People Detector KitAre you tired of your little sister/brother sneaking into your room and getting into things? Well thiskit may be the answer. The Magic People Detector Kit uses an IC circuit “brain” that senses tinychanges in the ambient light striking its “magic eye”. It sets off a loud siren when it detects someonein its view. The kit can guard the entrance to your room or you can set it up to warn you whensomeone comes down the hallway, etc. Works with room lighting or natural light (will not work indarkness). This fun and practical kit is very unique. Operates from 9V battery (not included). Sizeof board: 3 1/8” x 2”. Complete with all parts, PC board and instructions. Skill Level 3.optional plastic Type 5 box C6367 $3.90The Magic People Detector Kit................................................C6738 $10.25Wake Up Alarm Kitoptional plastic Type 5 box C6367 $3.90Here’s the perfect kit for the person that wants to sleep in but has to get up at sunrise. Featuresminiature vibrator motor which sounds like a crazed bumble bee and a yellow LED which glowsfaintly at night to show you that the kit is armed. CDS cell and transistor circuit has push on/pushoff switch and operates for over a month of regular use on just 2 standard AA batteries (notincluded). The kit is sensitive enough that it does not require direct sunlight and by varying thelocation of the kit you can vary the time at which the kit begins to buzz. Size of PC board: 1”x 2”. Complete with all parts, PC board and instructions. Skill Level 2.optional plastic TYPe 5 box C6367 $3.90Wake Up Alarm Kit......................................................................C6481 $5.9534Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Secret Alarm KitThis is the perfect device to scare off someone who opens your desk, dresser, file cabinet, lunchbox, etc. Simply turn the arming switch to the on position. You have a couple of seconds to put yourSecret Alarm in a desk and close the drawer. The next time someone opens it, a loud obnoxiousnoise comes from the horn until unit is reset. Uses sensitive CDS and SCR circuit to respond tolight. As long as it is kept in the dark it is quiet, but when light hits the sensor, WATCH OUT! Sizeof board: 3.75” x 2.25” Operates from one 9V battery (not included). Complete with all parts, PCboard and instructions. Skill Level 1. optional plastic Type 5 box C6367 $3.90Secret Alarm Kit..........................................................................C6455 $7.25PIR Wireless Alarm System KitTurn on a lamp, siren, horn, etc, when a human intruder is detected by this kit. Uses a sophisticated PIR sensorthat is fully assembled and a 433MHz receiver that you build. The PIR can detect the presence of a humanat up to 40 feet away and transmit the intruder detection to the tiny 433MHz receiver kit that you build. Thereceiver consists of a pre-assembled front end 433MHz receiver module and a pre-programmed microcontrollerIC circuit which must be assembled. The size of the receiver PC board is 2.05” x 1.35”. It operates from one9V battery (not included) and has a relay that can switch on your 120VAC lamp, optional sound bomb, orany device of your liking up to the current rating of the contacts. The receiver kit turns on devices for about15 seconds each time an intruder is detected, then resets itself and waits for the next activation. The PIRsensor uses one 9V battery (not included) and can operate for up to a month before the battery needs tobe replaced. The receiver unit can be activated by more than one sensor, so if you purchase more than onesensor you can protect various rooms, garage, etc, in your house. Receiver range to sensor is about 30 feet.Complete package containing one pre-assembled sensor, all parts, PC board and instructions to build thereceiver. Skill level 2. optional plastic Type 2 box C6364 $2.40PIR Wireless Alarm System Kit...............................................C7003 $28.95ALARM KITSGot-Ya KitOne of the sneakiest, disruptive, frustrating kits ever made. Just the ticket for a curious friend who just can’tresist picking up this innocent looking creation. As soon as he or she picks it up, it emits an obnoxious noisewhich can’t be silenced -you can’t turn it off with the switch and the way it is constructed you can’t evenremove the battery! Once they pick it up, they have really messed up, that is unless someone knows theone secret turn off procedure! Uses IC, SCR, CDS cell and transistor circuit. Works on one 9V battery (notincluded). Size of circuit board: 4.125” x 3.875”. Comes with all parts, PC board and instructions (you needto supply glue). Skill Level 2.optional plastic Type 5 box C6367 $3.90Got-Ya Kit......................................................................................C6464 $9.25Burglar Alarm KitUniversal type burglar alarm kit has on board horn and red LED “ON” indicator. Can be used with eithernormally closed and/or normally open loops. This allows you to use reed switches, foil, lever switches,mat switches or just about any type and quantity of switches (switches not included). With the ability touse N.C. and N.O. switches many areas can be protected by this one kit. Operates from 6VDC (batterynot included). Size of board: 3.6” x 2.5”. Skill Level 1.optional plastic Type 5 box C6367 $3.90Burglar Alarm Kit........................................................................C6280 $7.25Window/Door Burglar Alarm KitThis kit makes a great burglar alarm for your home. Whenever anyone attempts to open yourwindow, this kit produces a loud pulsating electronic sound from the built in piezo speaker andit also flashes a bright red LED. The sound won’t stop, even if the window is closed again. Onlyyou can shut it off. The kit will protect a window or door. It is very simple to install as only a smallmagnet (included) needs to be attached (glued) to the movable window or door. Uses IC, SCRand transistor circuitry. Operates on a 9V battery (not included). Size of PC board: 2 1/8” x 3 7/8”.Complete with all parts, PC board, reed switch, magnet and instructions. Skill Level 2.optional plastic Type 5 box C6367 $3.90Window/Door Burglar Alarm Kit.............................................C6703 $8.25Insanity Alarm KitSet this kit in an inconspicuous place with light shining on it and it remains perfectly silent,however, as soon as the light is turned off the kit emits a high pitched irritating tone! When theyturn the light on again to look for the culprit it keeps silent again! Easy to build and loads offun to use. Operates from one 9V battery (not included). Size of board: 2.9” x 1.8”. Completewith all parts, PC board and instructions. Skill Level 1. optional plastic Type 2 box C6364 $2.40Insanity Alarm Kit.......................................................................C6240 $5.25Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 35

SPECIALTY KITSSecret Squealer KitThis is a strange and amusing kit! Just connect the battery and it happily emits a strangehigh pitched squeal once every minute. If you’re not the one that hid the Secret Squealer,it’s pretty difficult to find, because it only squeals for a second, then it is quiet again untilits 1 minute rest period is over! Size of board: 2” x 2.25”. Operates from one 9V battery(not included). Complete with all parts, PC board & instructions. Skill Level 1.optional plastic Type 3 box C6365 $3.00Secret Squealer Kit....................................................................C6379 $5.25Metal Locator KitDetect coins, rings, buried treasures, etc. with this simple to build kit. Transistorized circuit usessensitive circuit and coil. Can detect up to 5” away depending on size of object. The metallocator detects metal by a shift in tone which is transmitted to a standard portable AM radio(you supply). Operates from one 9V battery (not included). Size of board: 1.5” sq. Completewith all parts, PC board, and instructions. Skill Level 1.optional plastic Type 5 box C6367 $3.90Metal Locator Kit..................................................................................C6742 $4.50IR Controlled Spinner KitIf you’re channel surfing with your TV remote control and you get bored, simply aim yourremote at this kit and the bright red hypnotic wheel starts rotating. Uses a motor anda sensitive IR module to allow it to operate with any brand or type of IR remote controlmade. Easy to build kit uses one 9V battery (not included). Size of PC board: 3 1/8” x 11/4”. Complete with all parts, spinner, label, PC board and instructions. Skill Level 1.NOTE: You provide the TV or DVD IR remote control.IR Controlled Spinner Kit..........................................................C6778 $5.25Large Glowing Light Panel KitHypnotic Bars Kitoptional plastic Type 3 box C6365 $3.00The Large Glowing Light Panel Kit uses a single IC circuit to drive a miniature white fluorescentbulb to light up a 3.4” x 4.6” white glowing plastic panel. On top of the display you place aclear piece of transparency film which you can use any permanent marker to write your name,draw a picture, design etc. If you want to change the design just replace the film. Can be usedfor custom message boards, night light and backlighting. Operates on one 9V battery (notincluded) or optional AC adapter. Overall size of panel and frame is about 4.5” x 6”. Size ofPC board is 1.5” x 2.5”. Complete with all parts, PC board, instructions, and transparent film.Skill level 2.Large Glowing Light Panel Kit.......................................................C7034 $10.95Gotta Glow KitThis amazing kit produces beautiful glowing color shapes that are mesmerizing andsoothing. Colors are produced by ultra-bright Blue, White and Red LEDs. IC circuitrycauses the patterns to appear and then fade away as the color changes. Featuresvariable color fade rate control and comes with a 3” x 4” white opaque panel (you mustprovide a box or mounting arrangement for the panel as only the panel is included withthe electronic kit). By experimenting with the angle and distance between the opaquepanel and LEDs, you can create some stunning visual effects. Operates from one 9Vbattery (not included). Size of PC board: 3” x 4”. Complete with all parts, PC board,opaque panel, and instructions. Skill Level 2.optional AC ADAPTER C7277 $2.99Gotta Glow Kit.............................................................................C6915 $9.95This unusual kit consists of 10 bright green LED bars which shimmer or flash for ahypnotic looking display. Kit features 1 IC circuit with a “Bar Effect” control to adjustthe back and forth flashing for the optimum unique shimmering display. Although the kitwon’t hypnotize you it really has a unique attention getting display of bright green bars.Operates from one 9V battery (not included). Size of PC board 2” x 1 1/2”. Completewith all parts, PC board and instructions. Skill Level 2.optional plastic Type 1 box C6363 $1.80Hypnotic Bars Kit.....................................................................................C6772 $5.2536Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Transistor Tester KitSmall transistor tester tests both NPN and PNP type transistors. Identifies automaticallywhich type of transistor you have plugged into the socket. Uses 2 ICs, 2 red LEDs, and1 bi-polar LED to show type of transistor, good functioning quality, opens and shorts.Simple to use and very useful for identifying unmarked transistors for type and whetherthey are good or bad! Size of board: 1 1/4” x 2 3/8”. Operates from one 9V battery(not included). Complete with all parts, PC board and instructions. Skill Level 2.optional plastic Type 2 box C6364 $2.40Transistor Tester Kit...................................................................C6448 $6.25Manual Siren KitThis kit produces upward and downward wail of a “police siren” as push-button isdepressed then released. Good for sound effects, parties, etc. Kit is small in size butproduces a loud tone from a small speaker. Kit features transistor and IC circuitrywhich operates from one 9V battery (not included). Size of PC board: 2 3/4” x 2”.Complete with all parts, PC board and instructions. Skill Level 1.Manual Siren Kit..........................................................................C6382 $6.75Super Siren KitWhen you need a real irritating siren, you need the Super Siren Kit.It features one special IC that contains 3 separate transistors and ahigh gain power amp. Great for getting everyone’s attention in theclassroom! Siren sound is the pulsating automatic electronic typeand features 2 separate sound adjustments. Size of board: 2.5”x 2.75”. Operates from one 9V battery (not included). Completewith all parts, speaker, PC board & instructions. Skill Level 2.One IC Speaker Radio Kitoptional plastic Type 3 box C6365 $3.00optional plastic Type 4 box C6366 $3.60Super Siren Kit..............................................................C6474 $8.75You will be amazed with the performance of this little radio receiver. It operates based ona sophisticated radio IC and has a powerful antenna coil with a high-grade ferrite core sono external antenna is needed. It includes a volume control and a two transistor audioamplifier with a power transistor to drive the speaker. Easy to build and to operate, as noalignment is necessary. A great project to take home and be proud of! Approximate size ofboard: 3 1/2” x 2 1/4”. Operates from a standard 9V battery (not included). Complete withall parts, PC board, and instructions. Skill Level 1.optional plastic Type 4 box C6366 $3.60One IC Speaker Radio Kit..............................................C6749 $12.25Adjustable Flashing Bright Light LED KitSmall size Adjustable Flashing Bright Light LED Kit alternately flashes 2 groups of 4 LEDs. The first groupconsists of 2 green and 2 yellow LEDs and the second group consists of 1 green, 2 yellow and 1 orangeLED. The 2.2” x 0.75” kit also uses a one IC circuit with a trimmer control to adjust the speed of flashing.Operates on one 9V battery (not included). Great attention getter! Complete with all parts, PC board andinstructions. Skill level 2.optional plastic Type 2 box C6364 $2.40Adjustable Flashing Bright Light LED Kit...................C7019 $4.253D Shimmering Pyramid KitGiant 3D pyramid shimmers mysteriously to delight and amaze everyone! Uses 75 jumbo red LEDs on a 3 dimensionalpyramid that stands over 4’’ tall and has a base of 6’’ x 6’’ x 6’’. Our 3D shimmering pyramid kit features a hidden controlto vary the effect from an overall shimmering effect to a sequencing effect which features bands of LEDs that sequencefrom the base to the top. Stunning and mysterious pyramid will be the focus of attention wherever it is placed. Operatesfrom one 9V battery (not included). Has a two IC circuit and uses 4 separate circuit boards (3 LED boards and 1 ICboard). Complete with all parts, PC board and instructions. Skill Level 3. This kit requires soldering of components tothe PC board while building. (Please do not attempt this kit if you have never built a kit).3D Shimmering Pyramid Kit....................................................C6437 $25.75Specialty KITSRADIO KITSFLASHING LED KITSChaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 37

FLASHING LED KITSAmazing Arrow KitOptional AC Adaptor: C6401 $4.95Giant bars of LEDs light up sequentially as this arrow appears to move! Absolutely amazing visualeffect using 63 LEDS and a variable speed control. Great as an attention getter, people director, oruse 2 kits as an auto directional signal (check local laws). Kit comes with 9V battery snap but willalso operate on any voltage between 5V and 12VAC or DC. Kit is available in one of three bright LEDcolors: red, green or yellow. Optional AC adapter is available. Size of board: 5 1/2” x 4”. Completewith all parts, PC board and instructions. Skill Level 2.Arrow with Red LEDS................................................................C6398 $18.50Arrow with Green LEDS............................................................C6399 $20.50Arrow with Yellow LEDS...........................................................C6400 $20.50Flashing Arrow Kit7-Speed Perpetual Blinker Kitoptional plastic Type 5 box C6367 $3.90Our Flashing Arrow Kit uses 16 bright red LEDs and one IC to provide a unique “arrow” that flashes.The IC circuitry features a small trimmer resistor to adjust the speed at which the “arrow” flashes.Operates on one 9V battery (not included). Size of PC board is about 2 3/8” square. Complete with allparts, PC board and instructions. Skill Level 2.optional plastic Type 2 box C6364 $2.40Flashing Arrow Kit......................................................................C6923 $5.75Here you have it! This is the ultimate blinker kit! It not only blinks three powerful clear LEDs for monthswhen powered by two “AA” alkaline batteries, but also includes an 8 position DIP switch that turns thekit on and off and adjusts the speed of operation. Seven different blinking speeds can be achieved bychanging the settings on the DIP switch. Approximate blinking speeds vary between 10 to 60 flashesper minute. This kit is ideal to put in the front or rear of your bike when biking at night. Hang it on yourclothes or hat when jogging or for Halloween. It also is great to put inside your car or by your windowat home for a fake alarm system. We are sure you will find many other applications. Approximate sizeof board: 4” (base) x 2 3/4” x 2 3/4”. Operates from two AA batteries (not included). Complete with allparts, PC board and instructions. Skill Level 1.optional plastic Type 5 box C6367 $3.907-Speed Perpetual Blinker Kit.................................................C6744 $4.75Electronic Fireworks KitExciting kit electronically creates an exploding “firework” like display. Kit features 17 micro red LEDs,7 green mini LEDs and 1 jumbo red LED. The circuit uses a 2 transistor multi-vibrator that alternatesbetween the “rings” of LEDs, which cause a display like “sky rocket” type fireworks. Great attentiongetter in a darkened room. Attractive and makes an interesting intermediate project. Size of board:3.875” x 3”. Operates from one 9V battery (not included). Complete with all parts, PC board andinstructions. Skill Level 2.optional plastic Type 5 box C6367 $3.90Electronic Fireworks Kit...........................................................C6454 $7.25XXL Green LED Flasher KitOur extra extra large (XXL) LED Flasher Kit features 2 mammoth (10MM) green LEDs that alternately flash.Circuit uses 1 IC and operates from one 9V battery (not included). Great for hundreds of applications! Infact, if you need to attract attention in a large way the XXL size is for you. Size of PC board: 2” x 1 3/16”.Complete with all parts, PC board and instructions. Skill Level 1. optional plastic Type 2 box C6364 $2.40XXL Green LED Flasher Kit......................................................C6791 $4.25Giant LED Traffic Light KitUnique attention getting Traffic Light Kit uses 3 bright, colorful, giant 10mm LEDs. Just like areal traffic light, this smaller version slowly sequences through green, yellow and red lights.Comes with a paper traffic light label you glue on the PC board and uses a 3 transistorsequencing circuit. Works from one 9V battery (not included). Size of PC board is 3 1/4”L x 115/16”W. Comes with all parts, PC board & instructions. Skill Level 1.optional plastic Type 3 box C6365 $3.00Giant LED Traffic Light Kit.......................................................C6810 $7.25Flashing Stop Sign KitThis kit features 20 small LEDS which flash a bright red color. Features a red and white labelwhich you glue to the octagon shaped PC board and a reliable 1 IC circuit. The circuitry featuresa small control to adjust the flash speed. Operates from one 9V battery (not included). Overallsize: about 5” x 5”. Complete with all parts, label, PC board and instructions. Skill Level 1.optional Type C MOUNTING BASE C6622 $2.50Flashing Stop Sign Kit..............................................................C6788 $10.2538Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Fantastic Atom Expander KitGiant visual effect kit uses 98 bright red LEDS to provide an “exploding atom” electronic display. Kit sequences froma small “nucleus” center to consecutive larger rings, then “shrinks” back to the center again. Absolutely incredibledisplay for science exhibits, game rooms, art displays or any place where you need to attract attention. Kit requireslonger assembly time than most of our kits due to the large number of components. Please don’t attempt this kitunless you have built other kits. Size of board: 8” x 5 3/4”. Operates from one 9V battery (not included). Completewith all parts, PC board and instructions. Skill Level 3.optional Type C MOUNTING BASE C6622 $2.50Fantastic Atom Expander Kit...............................................................C6373 $27.75Brilliant 3D Shimmering White Cube KitThe Brilliant 3D Shimmering White Cube Kit uses 125 ultra bright 10,000MCD white LEDs that flash or shimmer depending onthe hidden control setting. Operates from one 9V battery (not included) and uses 6 PC boards. The small one IC control boardand 9V battery are located out of sight inside the 2.5” square cube. The light effects from this kit are amazing! The output is abrilliant strobe flash to a dazzling shimmering effect (depending on the control setting). This kit is time consuming to build andshould not be attempted by anyone who has not built kits before. Assembling this kit requires good soldering skills, howeveryou will be rewarded with a stunning display! Complete with all parts, 6 PC boards and instructions. Skill Level 3.Brilliant 3D Shimmering White Cube Kit...............................................................C6919 $29.95Fascination Star KitProduces an “exploding star” visual effect using 25 LEDs and IC circuitry. The center LED lights first then thenext group of LEDs light and then another set lights until the outer edge of the star lights up. The process thenreverses itself. Great attention getter for game rooms, discos, etc. Operates from one 9V battery (not included).Size of board: 5.25” x 3.5”. Complete with all parts, PC board and instructions. Skill Level 3.Fascination Star Kit................................................................................C4432 $13.25Rock Star Kitoptional plastic Type 5 box C6367 $3.90Thinking about stardom? With your skill level 3 talent you can create your own rock star. This Rock StarKit is sure to light up the billboards with 78 ultra bright LEDs that sequentially flash R.O.C.K.S.T.A.R.one letter at a time. The Rock Star kit uses 2 ICs and has 2 PC boards. The control PC board allowsthe speed of the letters to be adjusted. Approximate size: main board 2.6” x 4.5” and the control board1.4” x 2.9”. Operate from a standard 9V battery (not included). Complete with all parts, rockstar label,2 PC boards and instructions. Skill Level 3.optional plastic Type 4 box C6366 $3.60Rock Star Kit.........................................................................................C6955 $14.95FLASHING LED KITSRed White & Blue Star Strobe KitStrobing red white and blue LEDs on this 3” star produce a blinding bright flashing display. Uses one IC circuit with 20 brilliant LEDsand an adjustable control for flashing speed. The star can be seen from great distances and is very eye catching. Operates fromone 9V battery (not included). Size of PC board is 3.52”sq. Complete with all parts, PC board and instructions. Skill Level 2.Red White & Blue Star Strobe Kit..........................................................................C6912 $11.95Mysterious 3D Pyramid Kitoptional plastic Type 5 box C6367 $3.90Super LED Chaser KitHere is an exciting visual display! Three groups of 2 LEDs light up sequentially to provide a stunning display.Kit uses 6 jumbo LEDs and 3 transistors. Operates from one 9V battery (not included) and comes in yourchoice of colors. Size of PC board is 2 7/8” x 15/16”. Complete with all parts, PC board and instructions.Skill Level 2.optional plastic Type 2 box C6364 $2.40RED LEDs........................................................................................................C6825 $4.25Green LEDs.....................................................................................................C6826 $4.25Yellow LEDs....................................................................................................C6827 $4.25Super Bright Clear Case Red LEDs..........................................................C6828 $4.75Super Bright Clear Case Green LEDs......................................................C6829 $4.75Very unique kit consists of 3 circuit boards that when assembled form a 3 dimensional flashing LED pyramid. This mysterious andamazing kit features 47 bright LEDs that flash at a rate that you can adjust using a small control. Operates from one 9V battery(not included) and uses a reliable one IC circuit. The pyramid is about 3” high and has a 4 1/2” base. The pyramid is hollowinside and can be set on top of the 9V battery to conceal it. Complete with all parts, PC board and instructions. Skill Level 2.optional Type C MOUNTING BASE C6622 $2.50RED LEDs.............................................................................................................C6792 $13.25Yellow LEDs.........................................................................................................C6793 $13.25Green LEDs..........................................................................................................C6794 $13.25Blue LEDs.............................................................................................................C6795 $19.95Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 39

FLASHING LED KITSLED Flasher KitEasy to build kit uses the amazing 555 timer IC to alternately flash a red and green LED. The kitmakes a great attention getter and can be used in robots, warning lights, model railroads, spacemodels, etc. Operates from 5 to 9VDC. Size: 1.5” x 1”. Complete with all parts, PC board andinstructions. Skill Level 1.optional plastic Type 1 box C6363 $1.80LED Flasher Kit...........................................................................C3287 $3.75“T3” Tip Top Triangle Kit“T3” is a fun electronic triangle kit that uses a special 2 transistor multi-vibrator circuit to alternately flash the bottom trianglebase consisting of two brilliant clear lens LEDs (1 blue and 1 white) with the top clear lens LED (red). Size of PC board: 1.5”x 2-7/8”. Complete with all parts, PC board and instructions. Skill level 1. optional plastic Type 2 box C6364 $2.40“T3” Tip Top Triangle Kit.....................................................................C6982 $3.95Jumbo LED Flasher KitSimple to build kit uses a programmable unijunction transistor (PUT) to flash a jumbo red LED. Makes agreat first kit and is useful for all types of convention badges, posters, attention getters, hats, model railroads,model planes, etc. Operates from one 9V battery (not included). Size of board: 1.25” x 1”. Complete withall parts, PC board and instructions. Skill Level 1.optional plastic Type 1 box C6363 $1.80Jumbo LED Flasher Kit........................................................................C4567 $3.75Piranha LED Flasher KitThis kit produces blinding red bursts of light from 3 special “Piranha” LEDs. Uses the popular 555 IC andfeatures 2 controls. One control for the speed of flashing and one for the intensity of the LEDs. Operatesfrom one 9V battery (not included). Size of PC board 2” square. Complete with all parts, PC board andinstructions. Skill Level 2.optional plastic Type 2 box C6364 $2.40Piranha LED Flasher Kit...................................................................................C6951 $5.95Super LED Flasher KitOne of our most popular display kits, this kit is perfect for use in robot projects, space models, warning lights,etc. Features a two IC circuit which alternately flashes 4 LEDs: 2 red, 1 yellow and 1 green. Produces a brightand colorful display. Operates from one 9V battery (not included). Size of board: 2” x 2”. Complete with all parts,PC board and instructions. Skill Level 1.optional plastic Type 2 box C6364 $2.40Super LED Flasher Kit.....................................................................................................C4407 $5.25Flashing Triangle KitThis triangle shaped LED flasher has 8 jumbo red LEDs that flash brightly. Kit is divided into two independentLED flasher groups with one group of LEDs flashing at a faster rate than the other. This difference producesan exciting display. The circuit consists of two independent multi-vibrator transistor circuits each drivingfour LEDs. Although this kit is a little more complicated than many of our Skill Level 1 kits, it can be builtby a Skill Level 1 student if the teacher gives some supervision. Size of board: 3.8” x 3.8” x 3.8”. Operatesfrom one 9V battery (not included). Complete with all parts, PC board and instructions. Skill Level 1.optional plastic Type 5 box C6367 $3.90Flashing Triangle Kit.............................................................................C6440 $5.75Ultra-Bright RGB LED 7 Color LED Flasher KitThis amazing kit uses a single ultra-bright RGB (Red Green Blue) LED to produce 7 different colors! By combiningthe different LED elements inside the RGB LED it is possible to have Red, Green, Blue, Aquamarine (B+G),Purple (R+B), Yellow (R+G), and White (R+B+G). This kit uses a two IC circuit to continuously flash through apattern of colors. Features a speed control to adjust the flash rate and an on/off switch. This kit makes a uniquevisual display in the dark as the ultra-bright colors are very intense - perfect for parties or as a conversation piece.Operates from one 9V battery (not included). Size of PC board 2 7/8” x 2 3/4”. Complete with all parts, PC board,and instructions. Skill Level 2.optional plastic Type 4 box C6366 $3.60Ultra-Bright RGB LED 7 Color LED Flasher Kit........................................C6953 $7.95Sequential LED Flasher KitThis kit combines CMOS IC circuitry and 10 jumbo red LEDs to produce a unique visual display. LEDscontinuously light from right to left. Easy to build kit makes a great conversation piece, game room display,attention getter, etc. Operates from one 9V battery (not included). Size of PC board 5.3” x 1.5”. Completewith all parts, PC board and instructions. Skill Level 2.optional plastic Type 5 box C6367 $3.90Sequential LED Flasher Kit......................................................C4431 $8.0040Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

“Customizeable” Colorful Brilliant Blinker KitThis small easy to build electronic kit uses a special 2 transistor multivibrator circuit to alternately flash two brilliantclear lens LEDs. Each LED lights up with such an intense color that it will really attract attention. To make thiskit customizeable we give you 2 red LEDs, 1 green LED, 1 yellow LED, 1 white LED and 1 blue LED so that youcan make the color combination of your choice. Simply pick the combination of 2 LEDs that you want! Operatesfrom one 9V battery (not included). Size of PC board 1 1/4” x 1 3/8”. Complete with all parts (including the 6brilliant color LEDs), PC board and instructions. Skill Level 1.optional plastic Type 1 box C6363 $1.80“Customizeable” Colorful Brilliant Blinker Kit.......................................C6958 $4.50Bulk Colorful Brilliant Blinker KitHere’s a great economical way to introduce your students to the fascinating field of electronics. This bulk Package contains all the parts and PCboards to build 25 Colorful Brilliant Blinker Kits. You get 25 etched and drilled PC boards, a bag of capacitors, transistors, battery snaps, resistors,an assorted bag of 50 colorful LEDs containing 10 each of Red, Green, Yellow, Blue and White, a set of 25 individual instructions, and reclosablezip bags for you to distribute the parts to your students. These are all the components necessary to build 25 alternating bright and colorful flashingdisplays. Skill Level 1. (Batteries not included)C6944 $85.00/Package of 25Magic Light Sweep KitThis kit produces sweeping light bars that magically speed up or down depending on the ambient light level. In darkness, the bars (madeup of 4 bright clear lens LEDs each) rotate very slowly, then as the ambient light increases the sweeping increases and takes on a radarscreen appearance. If the ambient light is very bright the sweeping speed is so rapid that the kit appears to shimmer. This kit producesthese effects automatically and makes a great attention getting display. Size of board: 2.6” x 4.1”. Operates from one 9V battery (notincluded). Complete with all parts, PC board and instructions. Skill level 2. Three colors available. optional plastic Type 4 box C6366 $3.60Red Magic Light Sweep Kit..............................................................................................C6439R $9.95Green Magic Light Sweep Kit C6439G $11.95 • Yellow Magic Light Sweep Kit C6439Y $11.95FLASHING LED KITS“Blinder” LED Flasher KitThis kit features 3 crystal clear special LEDs which create brilliant flashes of orange-red light. The light output of this flasherkit can even be seen in direct sunlight. You’ve never seen anything like it! Great for night joggers, bicyclists, warning markers,etc. Size of PC board: 2” x 1.4”. Operates on one 9V battery (not included). Flash rate is adjustable with the built-in trimmerpotentiometer. Complete with all parts, PC board and instructions. Skill Level 1.optional plastic Type 2 box C6364 $2.40“Blinder” LED Flasher Kit...................................................................................................C6891 $4.50Brilliant Quadflasher KitThis kit produces an attractive display from 4 brilliant colored LEDs that flash in a random pattern. The LEDs have acrystal clear lens, however they light up with their brilliant color when activated: 1 white, 1 red, 1 blue, and 1 yellowishorange.Uses a CMOS IC and operates from one 9V battery (not included). Size of PC board is 2.5” x 1.8”. Completewith all parts, PC board and instructions. Skill Level 2.optional plastic Type 2 box C6364 $2.40Brilliant Quadflasher Kit.............................................................................................C6913 $5.95Expression Flasher KitsDesigned with the student in mind, this series of Chaney Kits offers eight different and exciting label-based project kits for you to proudly display.Each project kit features a custom designed full color label and a bright flashing red LED. Perfect for bedrooms, dorm rooms, teachers’ desks, offices,or any other place that you would like to expressyourself. These fun and easy-to-build kits make aperfect introduction to basic electronic circuit theoryand transistor function. Using 2 transistor circuitrypowered by one 9V battery (notincluded), each kit provides hoursof blinking amusement. Size of PC onlyBoard: 3 1/4” x 4 3/4”. Completewith all parts, PC board, color label $5.25and instructions. Skill Level 1. eachEach kit is sold separately.C6766C6767C6768No Bozo Blinker KitNo Entry KitNo Smoking KitRadiation Alert KitBiohazard KitSleep Deprived KitC6766C6767C6768C6769C6770C6771optional TYPE C mounting base C6622 $2.50C6769 C6770 C6771Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 41

Game Kits INFRARED KITSLaser Target KitHere’s a kit that provides a fun use for your laser pointer. Aim your pointer at the small “CDS Bull’s-eye”and if you strike it you will see a bright red star (made from 8 LEDs). The kit features a red LED aimingspot that can be switched on at night for target practice. The target can also be used inside during daylighthours as it has a control to adjust for ambient room light. The range of use is only limited by the range ofyour laser pointer. Create contests and sharpen your skills with this fun kit. Operates from one 9V battery(not included). Size of board: 2 1/2” x 2”. Complete with all parts, PC board & instructions. Skill Level 1.Laser Target Kit...........................................................................C6739 $5.75Infrared Transmitter KitThe Infrared Transmitter Kit shoots a high power infrared pulse beam each time the button is depressed.Make your own “phasor blaster” for infrared tag games, target practice, etc. Small size board (only 2.9” x1”) allows you to design a custom looking “phasor gun” to mount unit in. Can activate Infrared Target Kit(below) up to 50 ft. away (much further ranges can be obtained if you add a lens in front of the infraredLED). Note: although the target will work with any gun, this Infrared Transmitter Kit will work only with thebelow Infrared Target Kit. Operates from one 9V (battery not included). Complete with all parts, PC boardand instructions. Skill Level 2.optional plastic Type 2 box C6364 $2.40Infrared Transmitter Kit...............................................................C6393 $7.25Infrared Target KitExciting Infrared Target Kit flashes a red diamond every time it gets hit by an infrared beam. Unlike other targets, thistarget works with all infrared guns currently available. Super sensitive target is perfect for practice or tag games. Featuressensitive sensor, transistor, and IC circuitry with sensitivity control. Works in daylight or darkness. Use it with the InfraredTransmitter Kit above if you do not already own an infrared gun. Size of board: 4” x 2”. Operates from one 9V battery (notincluded). Complete with all parts, PC board and instructions. Skill Level 2.optional plastic Type 4 box C6366 $3.60Infrared Target Kit................................................................................................C6392 $10.25Remote Controlled Nightlight Kitoptional plastic Type 2 box C6364 $2.40Now you never have to worry about entering a dark room. Simply aim any IR remote (that you already own) atthis simple kit and 2 laser like brilliant LEDs light up and stay on for about 5 minutes. This gives you ample time towalk out of the room or hallway or to find and turn on the light switch for that room. Our remote controlled nightlightkit uses one 9V battery (not included) and will work with any DVD, TV, Stereo, etc. IR remote up to 15 ft. away.Uses sensitive IR detection module and Darlington circuitry. Size of PC board: 1 7/8” x 1 1/8”. Complete with allparts, PC board and instructions. Skill Level 1.optional plastic Type 1 box C6363 $1.80Remote Controlled Nightlight Kit.........................................................C6777 $5.25Skateboard KitTake a break and kick up your skate score with the skateboard kit game. Uses 5 different colored bright LEDsto indicate your rating. To get your rating the skateboard kit uses touch sensor pads that you place your fingertip on. The LEDs all begin to flash but when you remove your finger, the LED that remains on is your rating.Uses a 2 IC circuit and operates from one 9V battery (not included). Size of PC board 5.25” x 2.2”. Completewith all parts, PC board, label and instructions.Cliff-Hanger Game KitHave you ever met the challenge of mountain climbing? If not, this is your chance to do it electronically. “Cliff-Hanger” willlet you experience the thrill of mountain climbing and test your skills to reach the top! Easy? Not at all, but it can be done.In this game you will have to press the control button at the precise moment, to advance to the next level on your wayto the top of the mountain. If the control button is pressed at the wrong time you will fall to the bottom. You will not breakany bones but you will have to start all over again. This kit features a variable skill adjustment and LEDs of three differentcolors (red, green, and yellow). Operates from a 9V battery (not included). Size of PC board: 4 1/8” x 3 1/8”. Completewith all parts, PC board and instructions. Skill Level 2.optional plastic Type 4 box C6366 $3.60Cliff-Hanger Game Kit.................................................................C6723 $11.25Alien Attack Game Kitoptional plastic Type 5 box C6367 $3.90Skateboard Kit...................................................................................C6974 $8.75Aliens are coming in their warships and are dropping their bombs on you! The only way to defend yourself is byneutralizing their bombs before they reach the ground. The bombs fall at different speeds and in different directions.This kit includes 19 LEDs of three different colors (red, yellow and green), 3 action switches, a circuit board, three ICs,and other components. Operates from one 9V battery (not included). Size of board: 4 1/2” x 3 3/4”. Complete with allparts, PC board and instructions. Skill Level 3.optional plastic Type 5 box C6367 $3.90Alien Attack Game Kit...................................................................................C6727 $14.2542Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

The Tingler KitAre you a “Hero” or a “Wimp”? This kit will give you a chance to prove it! Just set the slidecontrol to the “Wimp” position and place your fingers on the touchpads. You’ll then receivea “tingling” sensation from the mild electrical voltage. Now slide the control towards the“Hero” position and you’ll find it’s much more difficult to leave your fingers on the touchpads(as the tingling sensation becomes much greater). This kit is fun to build and fun to use.Operates from one 9V battery (not included). Size of board: 2 1/2” x 1 1/2”. Complete withall parts, PC board and instructions. Skill Level 1.optional plastic Type 2 box C6364 $2.40The Tingler Kit.............................................................................C6740 $9.25Touch Sensitive Coin Tosser/Decision Maker KitThis small kit uses 3 transistors and 2 LED circuits to make decisions or replace coin tossing. Featuresone red and one green LED that flash at a high frequency when you touch the sensor wires.When you quit touching the sensor your decision is shown by the LED that remains on. Has controlto adjust the “odds”. Safe and fun to operate. Size of board: 1.6” x 2.2” Operates from one 9V battery(not included). Complete with all parts, PC board and instructions. Skill Level 1.optional plastic Type 2 box C6364 $2.40Touch Sensitive Coin Tosser/Decision Maker Kit..............C6354 $3.95GAME KITSSuper Time Reaction KitAmazing and fun to use kit tests your reaction! Simply depress the “start” button with yourfinger. Eight bright LEDs begin to flash in sequence. Then as fast as possible, press andrelease the “stop” button with the same finger. Your reaction rating is indicated by the labelnext to the bright LED which remains on! Have contests with friends to see who has the fastestreaction speed. Do you react with “Lightning Speed” or “Turtle Speed”? Our colorful kitwill tell you. Features adjustable speed control to set difficulty level and operates from a 9Vbattery (not included). Size of PC board: 3 1/4” x 4”. Complete with all parts, PC board andinstructions. Skill Level 2.optional plastic Type 5 box C6367 $3.90Super Time Reaction Kit...........................................................C6716 $8.75Mood Meter KitHere’s an electronic kit that’s fun to build and use. The kit features a colorful label that you glue onto thePC board and 10 bright colorful LEDs to indicate your mood. You simply rest two of your fingers on thesensors and the sophisticated “comparator” IC determines your skin resistance and lights up the appropriaterating: Blue LED= “Cool as a Cucumber”, Green LED= “Easy Going”, Yellow LED= “Warm Hearted”and Red LED= “Smokin Hot”. The LEDs light up the rainbow in colors and more color “bands” light ifyour skin resistance is lower (so if the red band lights, all the other colors will be on also). Operates onone 9V battery (not included). Size of PC board: 4” x 4 5/8”. Complete with all parts, label, PC board andinstructions. Skill Level 2.optional plastic Type 5 box C6367 $3.90Mood Meter Kit............................................................................C6775 $9.75Rolling Dice KitPush the switch on this kit and bright red dice “roll” rapidly. Release the button and one of six standarddice patterns stays on. That’s your number! If you are playing a game that requires two dice, simply rememberthe first number and roll one more time for the second number. Uses 21 bright red jumbo LEDsand two ICs to provide an electronic way to replace standard dice. Kit features black outline printed diceon top of circuit board. Operates from one 9V battery (not included). Size of board: 6.7” x 3”. Completewith all parts, PC board and instructions. Skill Level 1.Rolling Dice Kit............................................................................C6412 $13.25Wheel Of Fortune Kitoptional Type B MOUNTNG BASE C6621 $2.25Very popular game device! Push the start button and a bright red “ball” (LEDs) appearsto spin around ten numbers gaining speed as you hold the button down. When yourelease the button, the electronic ball appears to slow down and finally comes toa stop on one number. As the ball spins, a small speaker emits a ticking sound insynchronization. Features colorful faceplate and jumbo red LEDs. Operates from one9V battery (not included). Size: 2 5/8” x 2 7/8”. Complete with all parts, PC boardand instructions. Skill Level 3.optional plastic Type 5 box C6367 $3.90Wheel Of Fortune Kit.................................................................C3806 $11.25Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 43

GAME KITSMacho Meter KitAre you “macho” or a “nerd”? Or maybe you are a “jock”, a “wimp” or “very smart”.Whatever you are this kit brings back the days of the “Penny Arcade” with a modern twist.Five bright LEDs flash at random when you place your fingers on the touch plate. Whenyou remove your fingers the meter indicates “your rating” by the LED which remains on- MACHO, JOCK, SMART, WIMP or NERD. Lots of harmless fun to use and fun to build,Operates from one 9V battery (not included). Size of board: 5 1/4” x 2 1/4”. Completewith all parts, PC board and instructions. Skill Level 2.optional plastic Type 5 box C6367 $3.90Macho Meter Kit..........................................................................C6362 $9.00Digital Racquetball Game KitThis game is like playing racquetball against a computer opponent. The ball is representedby LEDs, and you have to “hit” the ball by pressing a button. If you do, the ball changesdirection, travels up the court, bounces off the wall, then returns for you to hit again. That’s notall! Suddenly the speed of the ball changes and you have to play faster or slower to keep upwith the game. This kit also includes an adjustable speed control so that beginners will enjoyplaying just as much as the “experts”. You have to keep on your toes though, because if youmiss the ball, the game stops and you will have to start over. Operates from one 9V battery(not included). Size of board: 4.5” x 3”. Complete with all parts, PC board and instructions.Skill Level 2.optional plastic Type 4 box C6366 $3.60Digital Racquetball Game Kit..................................................C6726 $14.25Grab the Gold Game KitThis exciting game kit features a bright red LED pyramid with a clear LED on top. When poweris applied each of the 10 LEDs light up in a sequencing pattern. If you press and hold thesmall pushbutton just before the top clear LED is to light, this LED will stay on illuminating itsbright orange glow indicating that you made it to the top and picked up the gold. If howeveryour timing is off, one of the red LEDs will light up indicating “you lost”. To make the gameeven more interesting, a control is provided to speed things up! When its adjusted to itsfastest position you’ll need excellent reflexes and eye to hand coordination to Grab the Gold!Operates on one 9V battery not included. Size of board 2 1/2” x 4”. Complete with all parts,PC board and instructions. Skill Level 2.Grab the Gold Game Kit............................................................C6876 $9.25IC Decision Maker KitIf you have ever had difficulty in making a decision then this kit may be just the answeryou’ve been looking for. When you depress a small on board switch a bright greenLED and a bright red LED begin to alternately flash. When you release the button,one of the LEDs stays on indicating the decision. Red means no and green meansyes. Fun to use and fun to build. Uses a CMOS IC and operates on one 9V battery(not included). Size of PC board: 1 3/8” x 1 7/8”. Complete with all parts, PC board& instructions. Skill Level 1.optional plastic Type 1 box C6363 $1.80IC Decision Maker Kit................................................................C6701 $3.95Deluxe Decision Maker KitLet this colorful “electronic brain” make all of your important decisions for you. Displaysthe results to your questions using a variety of bright colored LEDs. Uses a 2 IC circuitand a label you glue onto the PC board. Simply press the start button and all of theLEDs begin to flash. As soon as you release the button, one LED will glow to indicatethe “electronic brain’s” decision. Lots of fun to use and easy to build. Operates fromone 9V battery (not included). Size of PC board: 3” x 3 5/8”. Complete with all parts,label, PC board and instructions. Skill Level 2.Time Reaction Tester Kitoptional Type A MOUNTING BASE C6620 $1.75optional plastic Type 4 box C6366 $3.60Deluxe Decision Maker Kit.......................................................C6780 $7.25If you ever thought that your sense of timing was good here’s an electronic kit to proveit! If your timing is good the LED will stay on, if not the LED continues to flash. Operatesfrom one 9V battery (not included). Size of board: 1” x 2”. Complete with all parts, PCboard and instructions. Skill Level 1.optional plastic Type 1 box C6363 $1.80Time Reaction Tester Kit...........................................................C4516 $4.1544Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Lie Detector KitSimple to build kit emits a tone which changes with amount of skin resistancebetween two fingers. If you are relaxed, a lower pitched tone will be heard. Funto use and great for parties. Has 2 copper touch plates on circuit board andsmall speaker. Fun “poor man’s lie detector”! Operates from one 9V battery (notincluded). Size of circuit board: 1 1/2” x 2”. Complete with all parts, PC board &instructions. Skill Level 1.optional plastic Type 3 box C6365 $3.00Lie Detector Kit............................................................................C4657 $5.25Attitude Selector KitWhat kind of attitude do you have today? With this kit you won’t need to eventhink about it! All you need to do is place your finger on the sensor wires andthe “Happy Face” and “Sad Face” LED eyes will glow. When you remove yourfinger only one set of eyes will stay on indicating your attitude. It’s a fun kit tobuild and use. Features colorful label which you glue onto the PC board anda 3 transistor circuit with an “odds” adjustment control. Operates from one 9Vbattery (not included). Size of PC board: 4 1/8” x 3 5/8”. Complete with all parts,label, PC board and instructions. Skill Level 1.optional plastic Type 5 box C6367 $3.90Attitude Selector Kit...................................................................C6776 $5.250-12VDC Variable Power Supply KitThis is one of the most inexpensive and reliable power supply kits on the markettoday! It is ideal for powering breadboard experiments, small tape recorders, radios,amplifiers, calculators and various electronic projects. This kit features a transformer,a circuit protecting fuse, a power transistor, full-wave rectification, two radialelectrolytic capacitors, an LED power indicator, On/Off switch, a potentiometer andother components. This power supply has a reliable circuit design with momentarilyshort circuit protection. Power supply outputs a maximum current of 100mA@12Vand 200mA@6V or less. Operates from standard 120VAC. Size of board: 3 1/2” x2”. Complete with all parts, PC board and instructions. Skill Level 2.optional plastic Type 3 box C6365 $3.000-12Volt Variable Power Supply Kit.......................................C6724 $9.500-12VDC 1Amp Variable Power Supply KitThis is one of the most useful kits to have around. Features variable output from0 to 12VDC filtered at up to 1Amp. Uses IC voltage regulator and a heavy dutytransformer. Kit also features red, yellow and green LEDs that glow at differentoutput voltages to show approximate output voltage - no need for meters.Operates from standard 120VAC and is great for powering amplifiers, radios,projects, etc. Size of PC board 6.5” x 2.9”. Complete with all parts, PC boardand instructions. Skill Level 2.optional Type C MOUNTING BASE C6622 $2.500-12VDC 1Amp Variable Power Supply Kit..........................C6929 $19.95GAMES KITSPOWER SUPPLY KITSRegulated Triple Output DC Power Supply KitGreat for use in a laboratory, on a test bench, or for experimentation. Thispower supply is 3 variable power supplies in one unit. It features ±1VDC to±15VDC@400mA and +1V up to 21VDC@1Amp. Uses IC voltage regulatorand a powerful transformer for reliable operation. Operates from 120VAC, andfeatures 3 separate controls to adjust the 3 separate voltages. Size of PC board:7” x 3.9”. Complete with all parts, PC board and instructions. Skill Level 2.optional Type C MOUNTING BASE C6622 $2.50Regulated Triple Output DC Power Supply Kit................. C6895 $26.95Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 45

AMPLIFIER KITSGeneral Purpose Amplifier KitVery handy amplifier kit can be used as a full volume amplifier to providespeaker output on any item you have which now only drives an earphone.Produces good sound and features volume control. Size of board: 2.25” x 1.8”.Operates from 9V battery (not included). Complete with all parts, PC boardand instructions. Skill Level 1.optional plastic Type 3 box C6365 $3.00General Purpose Amplifier Kit................................................C6238 $9.25Megaphone KitWith this Chaney kit you can build a useful megaphone or PA system to amplifyyour voice. This kit is small and self-contained and includes a high-gain electretmicrophone, an IC audio amplifier, a volume control and a speaker. You willreally be amazed with the clarity of sound and power of this little amplifiersystem. Ideal for use as a megaphone, PA system, one-way intercom, or manyother applications where sound needs to be amplified. Approximate size ofboard: 1 3/4” x 1 1/4”. Operates from a standard 9V battery (not included).Complete with all parts, PC board, and instructions. Skill Level 1.optional plastic Type 5 box C6367 $3.90Megaphone Kit............................................................................C6746 $7.25Electronic Intercom KitVery useful kit for hundreds of two way communication applications. Usein campers to cab, home, office, school etc. Features high gain transistorand IC circuit with special noise reduction filter for clean sound. Kit comescomplete with 2 small speakers - one for master and one for remote. Youprovide any 2 conductor wire of your choice to interconnect the master tothe remote. Size of board: 2 1/2” x 1 1/2”. Operates from 9V battery (notincluded). Complete with all parts, PC board and instructions.Skill Level 1.Electronic Intercom Kit.............................................................C4743 $10.2520 Watt RMS Mono Amp KitHigh power amp for various booster applications. Kit features shortcircuit and open circuit protection and has very low distortion (1% orless). Amplifier has red LED “on” indicator and will boost any tuner, radio,cassette, CD player to room filling volume out of your speaker! Size ofboard: 3.75”x 2.1”. Operates from 12VDC. Complete with all parts, PCboard and instructions. Skill Level 2.optional plastic Type 5 box C6367 $3.9020 Watt RMS Mono Amp Kit......................................C6444 $17.5020W + 20W Stereo Amp Kitoptional plastic boxes: (1) Type 2 box C6364 $2.40and (1) Type 3 box C6365 $3.00Two separate high power amps on one PC board. Each amp hasits own level control and puts out an incredible 20 Watts RMS.Features red LED “on” indicator and low distortion circuitry. Greatstereo booster amp for your car sound system. Use with anyspeakers capable of handling at least 20 watts. Size of board:6” x 2.25”. Operates from 12VDC. Complete with all parts, PCboard and instructions. Skill Level 2.optional plastic Type 5 box C6367 $3.9020W + 20W Stereo Amp Kit.................................C6442 $23.7546Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

9VDC Strobe Warning Flasher KitCompact strobe flasher produces brilliant flashes of white light from a xenon horseshoe strobe tube. Features newlyrevised circuit for brighter output and less current drain. Operates from standard 9V alkaline battery (not included)and flashes approximately 40 times per minute. Great safety device and attention getter. Small board is only 1 7/8” x1 1/2”. Complete with all parts, PC board and instructions. Skill Level 2.9VDC Strobe Warning Flasher Kit..........................................................C5175 $13.25120VAC Variable Strobe Light Kitoptional plastic Type 3 box C6365 $3.00One of our most popular strobe light kits - thousands of these are in use. Features variable flash rate and straightxenon strobe tube. Speed can be varied from about 120 to 200 flashes per minute. Great for discos, parties,dances, displays, etc. Operates from standard 120VAC. Size of board: 3” x 2”. Complete with all parts, PC boardand instructions. Skill Level 2.120VAC Variable Strobe Light Kit.......................................................C3071 $11.25Deluxe Professional Xenon Strobe Kitoptional plastic Type 4 box C6366 $3.60Attractive and powerful xenon strobe kit comes complete with a custom designed case. Features operationfrom 120VAC, variable flash rate speed control, long life horseshoe xenon strobe tube and sturdy beige casewith clear front lens. This high quality kit has everything you need to make a reliable professional quality xenonstrobe that is perfect for parties, dances, theatrical effects, attention getters, etc. Complete with all parts, PCboard, case with lens, knob, instructions and power cord. Designed for heavy duty use with both thermalprotection and overload fuse protection. Size about 6 1/8”W x 2 1/8”H x 6 3/4” Deep. Skill Level 2.Deluxe Professional Xenon Strobe Kit.................................C6888 $27.95STROBE LIGHT KITS120VAC High Power Strobe Light KitDeluxe variable rate strobe light kit which is similar to the C4823 kit but produces a brighter flash. Features a horseshoeshaped strobe tube and includes a reflector. Has control to vary flash rate from 100 to 200 flashes per minute. Great for applicationsrequiring higher light output - discos, school dances, etc. Operates from standard 120VAC. Size of board: 4 1/2”x 3”. Complete with all parts, PC board and instructions. Skill Level 2.optional plastic Type 4 box C6366 $3.60120VAC High Power Strobe Light Kit........................................................C4162 $18.50Giant Super Power Strobe KitThis kit is probably the largest and brightest xenon strobe available anywhere in kit form. Amazing for Halloween, parties,theater productions and more. The Giant Super Strobe Power Strobe Kit uses a 9.5” x 04” borosillicate glass xenonstrobe tube custom made for us! The circuit uses four powerful photoflash capacitors and flashes brilliant white lightadjustable from about 70 to 200 flashes per minute by means of a potentiometer. Operates from 120VAC and the mainPC board is 5” x 2.5”. The strobe tube PC board is 12” x 0.8”. Complete with all parts, PC boards, large linear strobetube and instructions. This strobe should be mounted in an insulated case (not available from us). Please do not attemptto build this kit if you do not know AC safety precautions. Skill level 2.Giant Super Power Strobe Kit.....................................................................C7035 $29.95120VAC Brilliant Strobe Light KitGood medium priced strobe light kit which features variable speed and brilliant flashes of white light from ahorseshoe shaped xenon flashtube. Great for parties, discos, dances, etc. Reliable design circuit has controlto vary flash rate from about 120 to 200 flashes per minute. Another very popular strobe kit which will be thehit of the party. Operates from standard 120VAC. Size of board: 3” x 5”. Complete with all parts, PC board andinstructions. Skill Level 2.optional plastic Type 4 box C6366 $3.60120VAC Brilliant Strobe Light Kit...........................................C4823 $14.25Dual Strobe Light KitThis kit will be the hit of your next party asdual xenon strobe tubes alternately flashon this unique kit! Gives a “police” effectand is a great attention getter. Kit featurestwo straight xenon flashtubes and a fixedflash rate of about 120 per minute. Operatesfrom standard 120VAC. Size of board: 3”x3”. Complete with all parts, PC board andinstructions. Skill Level 2.optional plastic Type 4 box C6366 $3.60Dual Strobe Light Kit...............................C4622 $12.35Tiny Strobe Light KitTiny Strobe Light Kit operates from 3 AAAbatteries (not included) and produces abright white flash of light from a 1” long xenonstrobe tube. The flash rate with fresh batteriesis about 60 per minute (rate will slowdown as the batteries get weaker). Great forwarning flashers on bikes, RC airplanes, hiking, etc. Can be seen in brightsunlight! Uses 2 transistors and an efficient inverter circuit to produce thehigh voltage necessary for the xenon tube. Size of PC board is 1.8” square.Complete with all parts, battery holder, and instructions. Skill level 1.optional plastic Type 2 box C6364 $2.40Tiny Strobe Light Kit...............................C6995 $9.95Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 47

SMD TECHNOLOGYThe latest technology in electronic products is Surface Mount Devices (SMDs). SMDs are tiny leadless (short lead) components that are used inalmost everything from computers to Phones. Now Chaney Electronics makes it possible for your students to learn more about surface mounttechnology through the construction of any of our SMD kits. Students use a drop of white glue (or any other glue that’s handy) to glue the partsto the PC board, then they solder the parts. We recommend using tweezers, a magnifying glass and a small tip soldering iron. NOTE: Please donot have beginners build these kits as we can not repair them due to the fact that the components are very tiny and glued onto the PC board.SMD Infrared Detector KitOur tiniest SMD kit is only 1” x .56”. It detects the infrared energy emitted by TV/DVDremotes, infrared lasers, etc. With each IR pulse a tiny red LED lights up. Simply holdthe remote to be tested about 2” from the detector kit and press each button to see ifthey are all functioning properly. Uses an IR sensor, SMD transistors, SMD resistorsand SMD capacitor. Operates from a 9V battery (not included). Complete with all parts,PC board and instructions. Skill Level 2.optional plastic Type 1 box C6363 $1.80SMD Infrared Detector Kit........................................................C6489 $5.95SMD Insanity Alarm KitHere is the SMD version of one of our all time best selling electronic kits. It operates the exactsame way- Just set this kit in a inconspicuous place with light shining on it and it remainsperfectly silent, however, as soon as the light is turned off the kit emits a high pitched irritatingtone! When they turn on the light again to look for the culprit, it keeps silent again! Operatesfrom one 9V battery (not included). Size of board only 1 5/8” x 1 7/16”. Complete with all parts,PC board and instructions. Skill Level 2.optional plastic Type 1 box C6363 $1.80SMD Insanity Alarm Kit.............................................................C6734 $5.25Brilliant Red and Blue SMD Flasher KitSmall brilliant LED flasher alternately flashes one red and one blue LED. Uses SMD (surface mountdevice) components so there are no holes in the PC board (all components mount to the small foil padson top of PC board). SMD is the most common technology in use today and this kit provides a niceintroduction for your students. Operates on one 9V battery (not included). Size of PC board 1.6” x 1.1”.Complete with all parts, PC board and instructions. Skill level 2.optional plastic Type 1 box C6363 $1.80Brilliant Red and Blue SMD Flasher Kit................................C6945 $4.95SMD/Hybrid Stereo Amplifier KitThis tiny SMD Hybrid stereo booster amplifier takes the output of any walkman, computer, radio, etc. and boostsit to full room filling volume. Uses a combination of standard lead components and SMD components to form aunique “Hybrid” assembly technique that is used in many industrial/commercial applications. The Stereo AmpKit uses a special SMD audio power amplifier IC which puts out an incredible 2.3 watts RMS per channel intoa 4 ohm load. Use with any stereo speakers you wish to use. Operates from any voltage 9V-14VDC. NOTE:Requires the use of super glue (not included). Has excellent frequency response and extremely low distortion.Circuit board size: only 2 1/4” square. Complete with all parts, PC board and instructions. Skill Level 2.SMD IC Star LED Flasher Kitoptional plastic Type 2 box C6364 $2.40SMD/Hybrid Stereo Amplifier Kit....................................... C6736 $13.35Our most advanced SMD kit uses a tiny 555 SMD IC to flash 5 tiny SMD LEDs. The LEDs flash with a brightyellow green color. Because this kit uses a tiny SMD IC, SMD resistors, a tiny SMD capacitor, and SMD LEDs,it provides the best introduction to SMD technology. We do not recommend this kit for beginning students asthe lead spacing on the IC is very tight and the kit must be assembled with patience and a small tip solderingiron. Great for advanced students, colleges and technicians wishing to learn more about SMD technology.Operates on a 9V battery (not included). Size of PC board: 1 3/4” x 2”. Complete with all parts, PC board &instructions. Skill Level 3.optional plastic Type 2 box C6364 $2.40SMD IC Star LED Flasher Kit...................................................C6708 $6.25SMD Light Sentry Alarm KitTiny SMD kit can be hidden in any darkplace, closet, desk drawer, briefcase, etc.The moment it senses light it emits a highpitched tone and it continues to scream untilyou return it to a dark place. The SMD LightSentry Alarm Kit is fun to build and use!Operates from one 9V battery (not included). Size of board only 15/8” x 1 7/16”. Complete with all parts, PC board and instructions.Skill Level 2.optional plastic Type 1 box C6363 $1.80SMD Light Sentry Alarm Kit..........C6735 $5.25SMD Flashing Initials KitVery unique kit flashes two initials of your choice on andoff. Features brilliant Green SMD LEDs that you installto form any two letters from A to Z or any two numbersfrom 0 to 9. Letters are 2” high and can be seen fromquite a distance. Complete with 44 SMD LEDs, all parts,PC board and instructions. Overall size of PC board 21/2” x 3”. Operates from one 9V battery (not included).Skill Level 3 (This kit is not for beginners).optional plastic Type 2 box C6364 $2.40SMD Flashing Initials Kit.............C6861 $13.2548Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

SMD Flashing Name Plate KitThis exciting Chaney Electronics kit features your “Name in Lights”. Features space for up to 8letters or numbers of your choice (A-Z or 0-9) made up of brilliant Green SMD LEDs. Your name orsimple message can be seen from across the room even in full light conditions. The name flashesat your choice of speeds from slow to fast. Each character is about 1 5/8” tall and you can use all8 or just the quantity you need to make your name. We give you 150 special brilliant green SMDLEDs (enough to make most 8 character names). Size of name plate PC board is 2 1/4” x 9 1/2”. Tocause your name plate to flash, a small 2” x 1 5/16” control board that uses regular “feed thru” (notSMD) components is used. This IC circuit features a variable flash rate speed control and operatesfrom one 9V battery (not included). Complete with all parts, 2 PC boards and instructions. Sorry,no case available. Skill Level 3. Not for beginning students.SMD Flashing Name Plate Kit..................................................C6867 $30.25TOL (Temperature, Ohm, Light) KitOur Temperature, Ohm, Light (TOL) Kit makes a great introduction to programmable integrated circuits (PIC) by demonstrating 4specific functions being handled by a single pre-programmed PIC. This kit measures three different parameters and displays themon a 3.5” LCD. This kit uses a PIC16F88 pre-programmed IC to allow you to measure resistance from 30 ohms up to 470k ohms,temperature from 35ºF to 130ºF and light intensity from 0% up to 100% (full sunshine). The PC board is about 4.4” long x 1.6”wide and comes with the LCD display already soldered in (the pins on the display are very close together so we solder and testthe connections to prevent solder bridges). Operates on one 9V battery (not included) and uses a built in thermistor to measureambient temperature, a CDS cell to measure relative light intensity (when the light intensity drops below 10% a bright yellow LEDlights up). Finally, the kit uses clip leads that you can attach to resistors to display their values in ohms. Complete with all parts,pre-programmed PIC, PC board with display installed and instructions. Skill level 2. optional plastic Type 5 box C6367 $3.90TOL Kit..............................................................................................................C6996 $19.95Continuity Tester KitHandy kit is a must for anyone working with electronic circuits. Traces circuit paths for continuity, checksfor broken wires, shorted contacts, etc. Uses small piezoelectric speaker which emits a pleasant toneand features a bright red LED visual indication. Operates from one 9V battery (not included). Size ofboard: 2 1/4” square. Complete with all parts, PC board and instructions. Skill Level 1.optional plastic Type 2 box C6364 $2.40Continuity Tester Kit....................................................................................C6385 $3.95CMOS/TTL Logic Probe KitThe Chaney C6722 CMOS/TTL Logic Probe Kit is a handy, reliable, and inexpensive. Designed tooperate with voltages between 5 and 20 volts, this logic probe is the ideal tool for troubleshootingCMOS and TTL digital circuits. It has a visual indicator that consists of a red LED and a green LED.The red LED indicates a High (1) logic state, and the green LED indicates a Low (0) logic state.This logic probe is small, easy to build, and easy to use. Operates from the power of the circuit beingtested. Size of PC board: 3 5/8” x 1 1/4”. Complete with all parts, PC board and instructions.Skill Level 1.CMOS/TTL Logic Probe Kit......................................................C6722 $6.25Battery Tester KitOur Battery Tester Kit is just the answer to test all types of common batteries. Simple to use–justselect the battery voltage to be tested by rotating the selection switch and connect the clipleads to the battery. If the battery is good, the green LED lights. If it’s bad the red LED lights.Kit features 5 calibration trim pots to allow you to set up your tester to test any 5 different typebatteries that you frequently use. Size of board: 2.6” x 3.5”. Operates from one 9V battery(not included). Complete with all parts, PC board and instructions. Skill Level 1.optional plastic Type 5 box C6367 $3.90Battery Tester Kit........................................................................C6414 $9.25SMD TECHNOLOGYTEST EQUIPMENT KITS3 Slot AC Outlet Tester KitThis very useful tester checks outlets for 6 different faults or safety hazard conditions anddisplays the results. Uses bright “orange glow” neon lamps to indicate if ground is connectedor if hot and neutral are reversed, etc. Compact and very useful accessory for any tool box.Operates from 120VAC. Size of PC board 2” x 2”. Comes complete with a Type 1 clearplastic box that the student can drill or file a hole in (to allow the cord to go into box) andthen mount the completed board into. A supplied label completes the project and allowsyou to have a handy, ready to go tester that will check out any 120VAC outlet in the house.Complete with all parts. PC board, undrilled plastic box and instructions. Skill level 2 (sinceit operates on 120VAC).3 Slot AC Outlet Tester Kit........................................................C6842 $6.25Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 49

THEME KITSElectronic Cricket KitHere’s just what you need to complete your home, an electronic cricket that starts “chirping”every time the lights go out. Of course if you turn on the lights to look for the “cricket”, itbecomes silent again. Uses a CMOS IC and CDS cell circuit with an adjustable “cricket” soundcontrol, that enables you to adjust your cricket to the chirp that you find most irritating. Simpleto build and loads of fun to use. Your electronic cricket is sure to get the attention it deserves.Operates from one 9V battery (not included). Size of the PC board: 1 7/8” x 2 1/2”. Completewith all parts, PC board and instructions. Skill Level 1. optional plastic Type 2 box C6364 $2.40Electronic Cricket Kit.................................................................C6707 $5.25Heart Throb KitHow fast will your heart throb? Are you the calm, silent, cold type or the hot-blooded casanovatype? Only The Heart Throb Kit knows for sure! This fun kit features a bright red heart whichhas the ability to flash at various rates for different people. Place your fingers on the contactsand see how fast the heart will throb! Kit features IC circuitry and 36 jumbo red LEDs. Operatesfrom one 9V battery (not included). Size of board: 3.6” x 4”. Complete with all parts, PC boardand instructions. Skill Level 2.optional Type A MOUNTING BASE C6620 $1.75Heart Throb Kit............................................................................C6410 $10.25The Haunted Pumpkin KitHere is the perfect kit to spice up your Halloween. In addition to alternately flashing its greenLED eyes with its red LED nose, it also produces an eerie, spooky electronic sound from its piezomouth. The kit operates from one 9V battery (not included) and uses a 2 IC circuit and full color“pumpkin label” for you to glue on to the PC board. Size of PC board: 5” x 3”. Complete with allparts, label, PC board and instructions. Skill Level 2. optional plastic Type 4 box C6366 $3.60The Haunted Pumpkin Kit........................................................C6783 $9.25Screaming Turkey KitColorful kit makes a great addition to any Thanksgiving celebration. Perfect for an unusual centerpieceor home decoration. Not only does the Screaming Turkey Kit produce a screaming turkey sound, but alsothe colorful red, green, and yellow LEDs light up and flash. The 2 IC circuit features 2 controls to adjustthe sound and flashing speed. Operates from one 9V battery (not included) and uses a full color “Turkey”label that is glued to the PC board before you install the components. Size of PC board: 5” x 3”. Completewith all parts, PC board, label & instructions. Skill Level 2.optional plastic Type 4 box C6366 $3.60Screaming Turkey Kit..........................................................................C6784 $9.75The Magical Snowman KitBring the spirit of the holidays alive with this animated classic character of the snowman. Uses colorfulgreen, red and yellow 3mm LEDs plus a magical rainbow color fader LED for the snowman’s top hatwhich changes into many different colors. Size of PC board 3.5” x 5”. Operates from one 9V battery(not included) that creates the stand. Complete with all parts, colorful label and instructions. Requiressoldering. Skill level 1.The Magical Snowman Kit..................................................................C6975 $6.95Magic Christmas Tree KitThis unique kit is sure to surprise all who see it! The kit shows a colorful Christmas tree which has 3white looking bulbs (actually LEDs). When a 9V battery (not included) is connected, the bulbs on thetree blink all red then all green and then back to red again. The effect is magic! Size of PC board: 21/2” x 2 5/8”. Circuitry uses 4 transistors to produce this unique display and a color label which youglue to the PC board before you start assembling the kit. Complete with all parts, label, PC board &instructions. Skill Level 1.Magic Christmas Tree Kit...................................................................C6773 $5.25Flashing Christmas Trees Kitoptional plastic Type 2 box C6364 $2.40Bright red and green Christmas trees alternately flash in this colorful kit. This kit uses one IC and 2 transistorelectronic circuit with 18 colorful miniature bright LEDs. Features adjustable flash speed control that can beadjusted from slow alternate flashing to a shimmering effect. Great attention getter, Christmas ornament, Christmasdisplay, etc. Size of circuit board: 3 5/8” x 1 7/8”. Operates from a 9V battery (not included). Complete with allparts, PC board and instructions. Skill Level 2.optional plastic Type 4 box C6366 $3.60Flashing Christmas Trees Kit..................................................C6711 $7.7550Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Jungle Bird KitThis kit produces the sound of canaries or exotic jungle birds. Features 2 controlsto adjust sound to produce various bird chirps. Great for your next “jungle” party! Asan added bonus the kit also has a pulsating red LED to add to the effect. Operatesfrom one 9V battery (not included). Size of board: 2 1/2” x 3 1/2”. Complete withall parts, PC board and instructions. Skill Level 1.optional plastic Type 3 box C6365 $3.00Jungle Bird Kit.............................................................................C6374 $6.75Mysterious Sound KitThe Mysterious Sound Kit remains silent for about 30 seconds after being “armed”(ample time to hide it in a room). After the 30 to 40 second time delay the tiny kit emitsa strange high pitched sound for several seconds then a loud “ticking” sound. The loudticking sound goes on all day unless someone finds where you have hidden it. Uses3 transistors, a piezo speaker, and has a control to adjust the speed of the “ticking”sound. Operates on one 9V battery (not included). Size of PC board is 1.7” square.Complete with all parts, PC board and instructions. Skill level 1.optional plastic Type 2 box C6364 $2.40Mysterious Sound Kit................................................................C7015 $5.95THEME KITSTOWS KitThe TOWS (Terribly Obnoxious Woodpecker Sound) Kit produces a very loudwoodpecker sound. This small kit just can’t be ignored as it generates the peckingsound of a crazed bird. Uses a small piezo and a two transistor electronic circuitthat generates a high voltage to provide a terribly loud “rapping/tapping” sound fromthe piezo. Features include a small control to adjust the speed of the “tapping”,and operation from a 9V battery (not included). Size of PC board: 2 3/4” x 1 3/8”.Complete with all parts, PC board and instructions. Skill Level 1.optional plastic Type 2 box C6364 $2.40TOWS Kit.......................................................................................C6712 $4.75Crazy Chirper KitHere’s the perfect kit to keep your unsuspecting guests entertained or should we say irritated.The chirper kit remains silent until the lights go out (just like a real cricket). The moment it getsdark the “chirper” starts to make its racket driving your guest crazy. Of course, when your guestturns the light on to look for the “chirper”, it becomes quiet again. This fun kit features a CDScell circuit with 2 transistors, piezo speaker and a flashing LED (which can be disabled). Thebuilt-in sound control allows you to adjust the sound from that of a crazy cricket to that of achirping canary. Operates from one 9V battery (not included). Size of board: 3” x 2”. Completewith all parts, PC board and instructions. Skill Level 1.optional plastic Type 2 box C6364 $2.40Crazy Chirper Kit........................................................................C6470 $4.95Create a Display Flasher KitThis kit allows you to flash your name, artwork, design etc at various speeds. The kit is very uniqueand uses a 2 5/8” x 1 1/8” electroluminescent panel (EL panel) that flashes brightly at your choiceof speed selected by a dip switch. On top of the display you place a clear piece of transparencyfilm which you can use any permanent marker to write your name, draw a picture, design etc. Ifyou want to change the design just remove the old film and place a new piece of film on the ELpanel. Very attractive and can be used to make flashing electronic nametags or desk nameplates.Operates on one 9V battery (not included). Flash speed can be adjusted from about 3 times aminute to a fast shimmering effect. Size of PC board 3 1/4” x 2 7/8”. Complete with all parts, PCboard, piece of film and instructions. Skill Level 2.optional plastic Type 5 box C6367 $3.90Create a Display Flasher Kit....................................................................C6906 $10.95Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 51

THEME KITSUNIQUE KITSPhasor Sound And Light KitThis kit produces the sound and light you’ve seen in the futuristic weapons used in most space movies!Phasor Kit features a control to vary the frequency of the sound. Great for attention getters, scienceprojects or use your imagination and place our kit in models, robots, phasor guns, etc. Operates from one9V battery (not included). Size of board: 2 3/4” x 2”. Complete with all parts, PC board and instructions.Skill Level 1.optional plastic Type 5 box C6367 $3.90Phasor Sound And Light Kit....................................................C6406 $7.25Kinetic Pirates Desk Sculpture KitAmazing and fascinating kinetic Pirates Sculpture features two chrome plated pirate figures on aseesaw. The seesaw rocks back and forth continuously making a clicking sound (like a clock), whilea beautiful emerald green LED flashes. This attractive desktop moving sculpture operates on 2 AAbatteries (not included) or optional AC adapter (not included). Requires soldering. Size of seesawis about 5”L. PC board is 2 5/8” x 3 1/8”. Complete with all parts, PC board, pirate seesaw andinstructions. Skill level 1. optional AC Adapter C17857 $4.95Kinetic Pirates Desk Sculpture Kit.........................................C7037 $9.95Kinetic Pirate Boat Sculpture KitSmall hypnotic kinetic sculpture features a chrome pirate rowing a boat. As the boat rocks back and forth continuouslymaking a clicking sound (like a clock), an emerald green LED flashes giving the illusion of the waves from the piraterowing. Very attractive sculpture is simple to solder and assemble. Chrome plated pirate in boat is pre-assembled. Thebase requires soldering. Operates from 2 AA batteries (not included) or optional AC adapter (not included). Size of pirateboat about 2 ¼ “ L. PC board is about 2” x 1” and is mounted on a 1 7/8” x 2 ¾” smoked grey acrylic base. Completewith all parts, PC board and instructions. Requires Soldering. Skill Level 1. optional AC Adapter C17857 $4.95Kinetic Pirate Boat Sculpture Kit............................................C7038 $8.95Cosmic Poppers KitThis very unusual kit emits random pops and random explosions of bright white light when it is in the dark (kit has a CDScell to sense the absence of light). This kit produces one of the most unusual “out-of-this-world” effects! Features SCRand CDS circuitry with 3 bright lamps and a piezoelectric speaker. Easy to build and it creates a spectacular display.It may even cause speculation as to whether or not it was left here by aliens! We put 4 of these into a darkened roomand the resulting sound and display was amazing. Size of PC board: 2.9” x 2.4”. Operates on 2 “AA” batteries (notincluded). Complete with all parts, PC board and instructions. Skill Level 1. optional plastic Type 4 box C6366 $3.60Cosmic Poppers Kit...................................................................C6893 $7.25Fish Caller KitThis kit produces a clicking sound which is said to attract fish. We have had customers who havereported excellent results, but who knows?! Anyway, it’s worth a try. Features a very tiny circuit boardand small piezo. Operates from one 9V battery (not included). Size of board only 1” x 3/4” so it canbe placed in almost any watertight jar and lowered into the water. Complete with all parts, PC board &instructions. Skill Level 1.optional plastic Type 1 box C6363 $1.80Fish Caller Kit..............................................................................C4566 $3.75The Aggravator KitThis exciting kit combines the most aggravating features from 2 of our most popular kits: the InsanityAlarm and the Secret Squealer. Hide this kit in a room and it will wait in total silence until the roomdarkens. In the dark it begins its aggravating function: for about 2 or 3 seconds every 3 to 5 minutesit emits a screaming tone. Any unsuspecting person will want to find the culprit so he will turn on thelights, but, the Aggravator Kit will remain silent again making it impossible to find. On returning tothe quiet of the darkened room the person will be startled again after 3 to 5 minutes. This is a fun,harmless kit that will bring hours of enjoyment. Complete with all parts, PC board and instructions.Operates from one 9V battery not included. Size of PC board: 1 1/4” x 2 3/4”. Skill Level 1.The Aggravator Kit.....................................................................C6840 $5.75Gravity Detector? Kitoptional plastic Type 2 box C6364 $2.40This kit detects gravity? Well, not really- What it does do is remain in an off state until a curious person lifts up thekit to study it. The “Gravity Detector” has a CDS cell underneath the board which activates when the board is liftedand gives the “curiosity seeker” a mild electric shock from the “handle” attached to the board. A great practicaljoke item! Uses IC, SCR and FET circuitry. Operates from one 9V battery (not included). Size of PC board: 4” x2”. Comes with all parts, PC board & instructions. Skill Level 2.Gravity Detector? Kit.................................................................C6894 $9.9552Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Classroom BulkPackage KitsSaveup toA great economical way to introduce your students to the fascinating field of electronics. Bulk packages containall the parts and PC boards to build 25 kits. In addition, a set of 25 individual instructions and recloseable zipbags are included for you to distribute the parts to your students. (Batteries not included).“Blinder” LED Flasher KitsPackage for up to 25 StudentsThis kit features 3 crystal clear special LEDswhich create brilliant flashes of orange-redlight. The light output of this flasher kit caneven be seen in direct sunlight.See page 41 for additionalkit details.C8100 $85.00Crazy Chirper KitsPackage for up to 25 StudentsHere’s the perfect kit to keep your unsuspecting guests entertainedor should we say irritated. The chirper kitremains silent until the lights go out (justlike a real cricket). The moment it gets darkthe “chirper” starts to make its racket drivingyour guest crazy.See page 51 for additionalkit details.C8102 $99.00Little JitterBug Robot KitsPackage for up to 25 StudentsBetter not leave any popcorn or chips around! This little jitterbugrobot is waiting for night, or when it’s completely dark, to roam thecountertops in search of goodies.The light sensor allows the jitterbug to come aliveand scoot around with the help of a tiny vibratingmotor.See page 30 for additionalkit details.Phasor Light and Sound KitsPackage for up to 25 StudentsThis kit produces the sound and light you’ve seen in the futuristicweapons used in most space movies! Great for attention getters,science projects or use your imagination and place our kit inmodels, robots, phasor guns, etc.See page 52 for additionalkit details.C8101 $145.00TOWS KitsPackage for up to 25 StudentsThe TOWS (Terribly Obnoxious Woodpecker Sound) Kit producesa very loud woodpecker sound. This small kit just can’t be ignoredas it generates the pecking sound of acrazed bird.See page 51 for additionalkit details.C8103 $95.00Expression Flasher KitsPackage for up to 25 StudentsDesigned with the student in mind, this series ofChaney Kits offers eight different and excitinglabel-based project kits for you to proudly display.Each project kit features a custom designed fullcolor label and a bright flashing red LED.See page 41 for additionalkit details.Classroom Bulk Package KitsC8104 $119.00Super LED Chaser KitsPackage for up to 25 StudentsHere is an exciting visual display! Three groups of 2 LEDs lightup sequentially to provide a stunning display. Kit uses 6 jumboLEDs and 3 transistors. Includesfive different LED colors.See page 39 for additionalkit details.C8106 $90.00C8105 $105.00Classroom Solder Practice Activity(With PowerPoint CD)for up to 24 StudentsHere’s the perfect way to introduce solderingto your students and give them the necessarysoldering experience needed to buildelectronic kits.See page 2 for additionalkit details.C6774 $120.00Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 53

MISC ITEMS4.5VDC 150mA AdapterThis small adapter plugs into standard 120VAC and putsout 4.5VDC at 150mA. The DC output cord is about 6 feetin length. Size of adapter is 2.2” x 1.7” x 1.5”. This adapteris optional for powering several of our kits.C17857 $4.95 ea.Compact VOM with BacklightThis is a great VOM! It features a data hold button, abacklight button that lights up the display for a few secondsso you can take readings in the dark, a continuity soundposition and a hFE (gain) test position for transistors. It canmeasure 0-600VDC in 5 ranges, 0-600VAC in 2 ranges, 0-2MegΩ resistance in 5 ranges, diode test and 0-10 amps in5 ranges. This deluxe digital VOM is only 5 1/2” x 2 3/4” x 15/8”. Includes a removable insulated holder. Brand new insealed retail blister package with built in battery and flexiblecolor coded insulated test leads.C7327 $19.95 ea.Special Soldering Helping HandsThis is the most useful of the “helping hands” series for anyone buildingor repairing electronic kits. It comes with fully adjustable clips for holdingyour circuit board, a quality magnifying glass, a small soldering ironholder and a sponge in the base. Just provide a soldering iron, wetthe sponge and you’re ready to go.C6694 $6.98 ea.SMD Tweezer MagnifierThis is one of the most useful items for working with SMDparts. Tweezer folds out from magnifying glass so that youcan get a clear view of the tiny part you’re picking up. Sizeabout 3 1/2” long.C6513 $3.50 ea.9V Battery SnapsPack of 100 9V battery snaps. We use these in our kits.C6539 $15.00Strobe TubeSingle Horseshoe strobe tube.C6566 $5.00Super LED AssortmentAssortment of all types, colors, sizes and shapes of primehigh quality LEDs. Assortment contains 100 pieces in areclosable bag.C6515 $7.00 ea.16 Pin IC SocketLow profile DIP ICsocket for 16 pinstandard DIP ICs.G16899 10/$2.5014 Pin IC SocketLow profile DIP ICsocket for 14 pinstandard DIP ICs.G16844 10/$2.258 Pin IC SocketLow profile DIPIC socket for 8 pinstandard DIP ICs.G16767 10/$2.00Large Universal BreadboardHandy breadboard for making prototype circuits. White 6 1/2”x 2 1/8” quick connect breadboard accepts almost all types ofelectronic components and wires. Consists of 126 groups of5 connected terminal points and 8 bus lines of 25 connectedterminals. High quality.C7113 $7.49 ea.555 Timer IC555 timer integrated circuit. We use these in many of our kits. Package of 10.C6544 $5.00Electronic Surprise BoxHere’s a way to help students learn to identify and study variouselectronic components while also providing a good source of resistors,capacitors, LEDs, diodes, IC’s, electronic assemblies, etc. This 8” x6” x 3” box is loaded with all kinds of electronic “goodies”. You willbe amazed at the variety and quality of these electronic parts. It’sa tremendous value!C6654 $10.00Bag of Electronic PartsZip close plastic bag containing about 40 popular electronic parts.You’ll get 5-red LEDs, a Green LED, a Yellow LED, 5-2N3904 NPNtransistors, 5-2N3906 Transistors, a 106 SCR, a 386 IC, 2-555 ICs,a 4001 IC, a 4011 IC, a 4017 IC, a 4093 IC, 2-Diodes, 2-9V snaps,plus several popular resistor and capacitor values!C6831 $8.00Bright Xenon Strobe TubeMicro xenon strobe tube features a brilliant flash. Requires 200Vcathode to anode voltage and any 4KV trigger coil. Size is .78” L x .14” Dia.G13722 $1.00Rainbow Flashing LEDOperates from a 3.5VDC and has a water clear lens. When power is appliedit flashes mixes and fades each color.G13897 $1.99SPDT Miniature Toggle SwitchMiniature toggle switch with panel mounting nut. 6 Amp contact rating.G1485 $0.95Small Powerful 12VDC MotorFeatures a .37”Long2.2mm Dia. shaft. Motorbody is about 1. 6”L x1.07”Dia. Operates from6VDC up to 18VDC.G15934 $0.99Package of Eight Workaholic9V BatteriesBrand new sealedpackage of eight9VDC WorkaholicAlkaline Batteries.G17178 $14.00Standard Size CDS CellFeatures a top surface of .16” x .14”dipped in a moisture-proof coating.Dark resistance over 4Mohm. Lightresistance less than 1KΩ.Package of 2.G15177 2/$1.00TransistorsOur mostcommonly usedtransistorsPkg of 100 2N3904 NPN Transistors.C6504 $20.00Pkg of 100 2N3906 PNP Transistors.C6505 $20.001/4 Watt Carbon ResistorsPrime color coded 1/4W carbon resistors. Select values from table at right. Order bystock number. 100/$3.50 Quantities of any one value (no mixing)1.0Ω C7150 36Ω C7165 220Ω C7178 750Ω C7191 5.1K C7204 18K2.7Ω C7151 39Ω C7166 240Ω C7179 820Ω C7192 5.6K C7205 20K3.9Ω C7152 47Ω C7167 270Ω C7180 1.0K C7193 6.2K C7206 22K4.7Ω C7153 51Ω C7168 300Ω C7181 1.5K C7194 6.8K C7277 24K5.1Ω C7154 68Ω C7169 330Ω C7182 1.6K C7195 7.5K C7208 30K5.6Ω C7155 82Ω C7170 360Ω C7183 1.8K C7196 8.2K C7210 33K10Ω C7156 100Ω C7171 390Ω C7184 2.0K C7197 8.5K C7278 36K12Ω C7158 120Ω C7172 430Ω C7185 2.2K C7198 9.1K C7212 39K15Ω C7159 130Ω C7173 470Ω C7186 2.4K C7199 10K C7213 43K22Ω C7161 150Ω C7174 510Ω C7187 2.7K C7200 11K C7214 47K24Ω C7162 160Ω C7175 560Ω C7188 3.3K C7201 12K C7215 51K27Ω C7163 180Ω C7176 620Ω C7189 3.9K C7202 15K C7216 56K33Ω C7164 200Ω C7177 680Ω C7190 4.7K C7276 16K C7217 62KC7218C7219C7220C7221C7222C7223C7224C7225C7226C7227C7228C7229C723068K75K82K91K100K120K160K180K200K220K240K270K300KC7231C7232C7233C7234C7235C7237C7238C7239C7240C7241C7242C7243C7244330K C7245390K C7246470K C7247510K C7248560K C7249620K C7250680K C7251750K C7252820K C72531.0Meg C72541.5Meg C72552.0Meg C72572.2Meg C72583.3Meg C72594.7Meg C72605.1Meg C727910Meg C726115Meg C726222Meg C728054Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

Chaney Electronics now offers a complete line of enclosures for your electronic projects. For economy and simplicity, we offerseveral sizes of crystal clear hinged plastic boxes. To give you more variety, we also offer four Display Base Mounting Kits.PLASTIC BOXESThese boxes can be drilled, painted and custom finished by you, or you can takethe plain box and simply place your project in it with a minimum effort. We include ageneral information sheet outlining methods you can use to customize your box. Wehave listed the recommended box size below each electronic project kit. The completebox list is shown below if you wish to compare sizes.TYPE 1 BOX 2”L x 2”W x 1 1/8”D C6363 $1.80TYPE 2 BOX 3 9/16”L x 2 9/16”W x 1”D C6364 $2.40TYPE 3 BOX 3 9/16”L x 2 9/16”W x 2”D C6365 $3.00TYPE 4 BOX 5 1/8”L x 3 1/8”W x 2 3/4”D C6366 $3.60TYPE 5 BOX 6”L x 4”W x 2”D C6367 $3.90Press-Apply RUBBER FEET for above Boxes C6397 Package of 4 for $1.00DISPLAY BASE MOUNTING KITSThese attractive grey acrylic mounting bases are perfect for finishing off your kit. EachDisplay Base comes with 4 press apply rubber feet and a piece of double-stick foammounting tape to mount your kit to the base.TYPE A BASE 4” x 6” C6620 $1.75TYPE B BASE 4” x 7” C6621 $2.25TYPE C BASE 6” x 8” C6622 $2.50TYPE D BASE 5” x 10” C6623 $3.0030 Watt Pencil Soldering IronComfortable grip pencil soldering iron is perfect for building several electronic projects or lightrepair work. The tip on this iron does not last as long as the tip on the soldering station below. Youcan re-file it several times to extend the use, but basically the iron is meant to be replaced after awhile. If this meets your needs, it is a cost effective way to build several kits. Comes with stand.C6652$4.50 ea.Deluxe Digital Soldering StationHigh quality soldering station has adjustable temperature range of 302˚ to 842˚F (150º to 450˚C). Featureslarge LCD display that shows the temperature of the iron and the set temperature. Has stand to holdiron and sponge for cleaning tip. Operates from standard 120VAC and is the perfect soldering iron forthe classroom. Our technicians and engineers use this at our company when building and designingthe Chaney Kits. It has a comfortable grip, a nice digital temperature control system, and replaceabletip if it should wear out. This soldering station is of course much higher quality than the pencil iron thatwe sell and is suited for long term use.C7272 $89.95 Replacement Tip for above: C7272 $4.95TYPE 1 TYPE 2TYPE 3 TYPE 4TYPE 5KIT BOXES & BASES Soldering ToolsHandy Tube of Rosin Core SolderPerfect for all types of electronic kitconstruction or repair. Slip it into yourpocket or tool chest. No hassle - easyway to have the right solder available when you need it. Tube isabout 3 1/2” long. Solder is about .031 diameter and is perfect foralmost every electronic application! Length about 8 ft.C6650Handy Solder WickGreat for de-soldering components from a PC board.Simply lay end of solder wick braid on top of PC solderpad and heat with solder iron. The solder “wicksup” into the braid so that you can easily remove thecomponent. 5 ft long–in a handy dispenser.C6651$1.75 ea.$1.49 ea.Side Cutting PliersHigh quality, chrome-plated, side cutting smalltype pliers. Sharp cutting jaws with spring typeinsulated grips. Very handy for kit building andvery good quality. Made in China. Size: 4 1/4” Long.C6511$4.95 ea.Needle Nose PliersHigh quality, chrome-plated, needle noseminiature pliers for precision electronicwork. Precision made with spring typeinsulated grips. Handy and precision made in China.Size: 5 7/8” long.C6512$4.75 ea.See Page 54 for AdditionalElectronic ComponentsChaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 55

NEY ELECTRONICS QUICK CHECK ORDER FORMDescription Pg# Qty. Cost Total Stock# Description Pg# Qty. Cost Total120VAC Strobe Light Kit 47 11.25LED Flasher Kit 40 3.75Wheel of Fortune Kit 43 11.25High Power Strobe Kit 47 18.50Light Sens. Sound Generator Kit 31 5.25Super LED Flasher Kit 40 5.25Sequential LED Flasher Kit 40 8.00Fascination Star Kit 39 13.25Time Reaction Kit 44 4.153 Channel Color Organ Kit 32 12.25Fish Caller Kit 52 3.75Jumbo LED Flasher Kit 40 3.75Dual Strobe Light Kit 47 12.35Lie Detector Kit 45 5.2510 Note Sound Kit 32 12.258 Note Organ Kit 31 10.25Single Chan Color Organ Kit 32 6.75Intercom Kit 46 10.25Plant Soil Monitor Kit 34 5.75Brilliant Strobe Kit 47 14.259VDC Warning Flasher Kit 47 13.25Amplifier Kit 46 9.25Insanity Alarm Kit 35 5.25Burglar Alarm Kit 35 7.253 Channel Sound Activated Kit 32 20.50Coin Tosser Kit 43 3.95Binary Counter Kit 33 12.25Decimal Display Kit 33 13.25Macho Meter Kit 44 9.00Type 1 Plastic Box 55 1.80Type 2 Plastic Box 55 2.40Type 3 Plastic Box 55 3.00Type 4 Plastic Box 55 3.60Type 5 Plastic Box 55 3.90Atom Expander Kit 39 27.75Jungle Bird Kit 51 6.75Secret Squealer Kit 36 5.25Manual Siren Kit 37 6.75Continuity Tester Kit 49 3.95Infrared Target Kit 42 10.25Infrared Transmitter Kit 42 7.25Red Arrow Kit 38 18.50Green Arrow Kit 38 20.50Yellow Arrow Kit 38 20.50Phasor Sound and Light Kit 52 7.25Heart Throb Kit 50 10.25Rolling Dice Kit 43 13.25Battery Tester Kit 49 9.253D Shimmering Pyramid Kit 37 25.75Magic Light Sweep Kit (Red) 41 9.95Magic Light Sweep Kit (Green) 41 11.95Magic Light Sweep Kit (Yellow) 41 11.95Flashing Triangle Kit 40 5.7520W X 20W Stereo Amp Kit 46 23.7520W RMS Mono Kit 46 17.50Learn to Solder Kit 25 7.25Shimmering Color Organ Kit 33 8.25Transistor Tester Kit 37 6.25Electronic Fireworks Kit 38 7.25Secret Alarm Kit 35 7.25Got-Ya Kit 35 9.25Crazy Chirper Kit 51 4.95Super Siren Kit 37 8.75Wake Up Alarm Kit 34 5.95Deluxe Burglar Alarm Kit 34 10.25SMD Infrared Detector Kit 48 5.95Deluxe Learn to Solder Kit 27 10.00IC Decision Maker Kit 44 3.95Window/Door Burglar Alarm Kit 35 8.25Electronic Cricket Kit 50 5.25SMD IC Star Flasher Kit 48 6.2533 in 1 Deluxe Electronic Exploration Lab 17 26.95Flashing Christmas Trees Kit 50 7.75TOWS Kit 51 4.75Super Time Reaction Kit 43 8.75Column A TotalFax US: (480) 451-9495Call Us: 1-800-227-7312C6719 Deluxe SMD Learn To Solder Kit 27 8.25C6721 35 in 1 Digital Lab Kit 16 35.95C6722 CMOS/TTL Logic Probe Kit 49 6.25C6723 Cliff-Hanger Game Kit 42 11.25C6724 0-12VDC Variable Power Supply 45 9.50C6725 Intro to SMD Technology 21 23.95C6726 Digital Racquetball Game Kit 44 14.25C6727 Alien Attack Game Kit 42 14.25C6730 44 Second Kit WEB 5.25C6734 SMD Insanity Alarm Kit 48 5.25C6735 SMD Light Sentry Alarm Kit 48 5.25C6736 SMD/Hybrid Stereo Amplifier Kit 48 13.35C6738 Magic People Detector Kit 34 10.25C6739 Laser Target Kit 42 5.75C6740 The Tingler Kit 43 9.25C6742 Metal Locator Kit 36 4.50C6744 7 Speed Perpetual Blinker Kit 38 4.75C6746 Megaphone Kit 46 7.25C6749 1 IC Speaker Radio Kit 37 12.25C6758 Universal Learn To Solder Kit 25 7.25C6761 IR Vision Robot Kit 30 35.95C6762 34 in 1 Deluxe Robotic Lab 20 71.00C6763 44 in 1 Communications Lab 15 45.95C6766 No Bozo Kit 41 5.25C6767 No Entry Kit 41 5.25C6768 No Smoking Kit 41 5.25C6769 Radiation Alert Kit 41 5.25C6770 Biohazard Kit 41 5.25C6771 Sleep Deprived Kit 41 5.25C6772 Hypnotic Bars Kit 36 5.25C6773 Magic Christmas Tree Kit 50 5.25C6774 Classroom Solder Practice w/ PP 2,53 120.00C6775 Mood Meter Kit 43 9.75C6776 Attitude Selector Kit 45 5.25C6777 Remote Control Nightlight Kit 42 5.25C6778 IR Control Spinner Kit 36 5.25C6780 Deluxe Decision Maker Kit 44 7.25C6783 Haunted Pumpkin Kit 50 9.25C6784 Screaming Turkey Kit 50 9.75C6785 Professional Burglar Alarm Kit 34 11.25C6786 Deluxe Blacklight in a Case Kit 31 23.45C6788 Flashing Stop Sign Kit 38 10.25C6790 Portable Filtered Blacklight Kit 31 17.45C6791 XXL Green LED Flasher Kit 38 4.25C6792 Red Mysterious Pyramid Kit 39 13.25C6793 Yellow Mysterious Pyramid Kit 39 13.25C6794 Green Mysterious Pyramid Kit 39 13.25C6795 Blue Mysterious Pyramid Kit 39 19.95C6810 Giant LED Traffic Light Kit 38 7.25C6815 Bright Star Color Organ Kit 33 6.75C6818 Exploding Star Color Organ Kit 33 16.25C6819 25 in 1 Magnetism Exploration Lab 22 21.95C6825 Super LED Chaser Kit - Red 39 4.25C6826 Super LED Chaser Kit - Green 39 4.25C6827 Super LED Chaser Kit - Yellow 39 4.25C6828 Super LED Chaser Kit - Super Bright Red 39 4.75C6829 Super LED Chaser Kit - Super Bright Grn 39 4.75C6831 Bag of Parts 54 8.00C6836 Additional Solder Practice Parts 2 21.50C6840 Aggravator Kit 52 5.75C6841 Sci-Fi Sound Theremin Kit 32 9.25C6842 3 Slot AC Tester Kit 49 6.25C6843 SolarBug Kit 10 10.25C6845 Learn to Solder Robot Kit 25 9.25C6853 10 in 1 Solar Energy Lab 18 30.95C6861 SMD Flashing Initials Kit 48 13.25C6864 Learn to Solder Rocket Kit 25 9.25C6865 Classroom Alien Warbot Pkg 28 107.00C6867 SMD Flashing Nameplate 49 30.25C6870 Alien Warbot Robot Kit 28 15.25C6871 IR Activator Robot Kit 28 16.25C6876 Grab the Gold Game Kit 44 9.25C6878 Chirp Chirp Kit 32 4.25C6880 4 in 1 Package A Solder Kits 7 15.25C6881 4 in 1 Package B Solder Kits 7 14.75Column B Total56Chaney Electronics, Inc. • 1-800-227-7312 • Fax: (480) 451-9495 • www.chaneyelectronics.com

CHANEY ELECTRONICS QUICK CHECK ORDER FORMStock# Description Pg# Qty. Cost TotalC6883 Aqualocator Kit 30 24.95C6886 Light Spider Robot Kit 28 12.25C6888 Deluxe Professional Xenon Strobe Kit 47 27.95C6889 Battery Operated Blacklight Kit 31 11.25C6890 26 in 1 Robotics Lab 14 52.95C6891 Blinder LED Flasher Kit 41 4.50C6893 Cosmic Poppers Kit 52 7.25C6894 Gravity Detector? Kit 52 9.95C6895 Triple Output DC Power Supply Kit 45 26.95C6898 Introduction to Kit Building 26 19.95C6900 Chrome Dome Robot Kit 29 24.95C6901 Chrome Dome Classroom Pkg 29 240.00C6902 Unstoppable Bug Robot Kit 29 18.95C6904 Solar Powered Speed Car 10 19.95C6906 Create a Display Flasher Kit 51 10.95C6907 26 in 1 Robots Lab (Pre-Soldered) 14 64.95C6908 Temperature Warning Kit 34 5.25C6912 Red White & Blue Star Strobe Kit 39 11.95C6913 Brilliant Quadflasher Kit 41 5.95C6914 Peanut Mover Robot Kit 29 14.95C6915 Gotta Glow Kit 36 9.95C6919 Brilliant 3D White Cube Kit 39 29.95C6920 Mini Light Spider Robot Kit 28 12.95C6923 Flashing Arrow Kit 38 5.75C6924 Compact Lightning Detector Kit WEB 14.95C6927 Racing Robot Learn to Solder Kit 27 12.95C6928 Learn to Solder Temperamental Robot Kit 24 9.95C6929 0-12V 1Amp Variable Power Supply Kit 45 19.95C6930 Solar Powered Brilliant Walklight Kit 11 10.95C6932 Complete Intro to SMD Kit Building 26 27.95C6933 Deluxe Introduction to Kit Building 26 29.95C6934 4 in 1 Package “C” Solder Kits 7 14.95C6935 4 in 1 Package “D” Solder Kits 7 15.50C6936 Electro Spinner Kit 33 14.95C6944 Bulk Brilliant Blinker Kit 41 85.00C6945 Brilliant Red & Blue SMD Flasher Kit 48 4.95C6946 Sun Spinner Robot Kit 10 19.95C6951 Piranha LED Flasher Kit 40 5.95C6953 Ultra-Bright RGB LED Flasher Kit 40 7.95C6955 Rock Star Kit 39 14.95C6958 Customizeable Brilliant Blinker Kit 41 4.50C6959 Magical LED Learn to Solder Robot Kit 23 8.95C6962 Out of Sight Kit 23 5.50C6964 Keep Out Kit 23 5.50C6966 Too Hot Kit 23 5.50C6967 Awesome Kit 23 5.50C6970 Customizeable R.O.H.S. Bllnker Kit 23 4.25C6972 Learn to Solder 9V Battery Tester Kit 27 9.00C6973 Unfiltered Blacklight Strobe Kit 31 10.95C6974 Skateboard Kit 42 8.75C6975 Magical Snowman Kit 50 6.95C6979 Sensitive Geiger Counter Kit 9 101.95C6981 Digital Display Geiger Counter Kit 9 139.95C6982 “T3” Tip Top Triangle Kit 40 3.95C6983 Solar Powered Boat Activity 19 24.95C6984 Little Jitterbug Robot Kit 30 5.95C6985 Solar Camping Light Kit 10 14.95C6986 Micro Geiger Counter Kit 9 99.00C6987 Jam Man Kit 24 25.95C6994 4 in 1 Package “E” Solder Kits 7 16.75C6995 Tiny Strobe Light Kit 47 9.95C6996 TOL Kit 49 19.95C6998 Alpha, Beta, Gamma Geiger Kit 8 149.95C7003 PIR Wireless Alarm System Kit 35 28.95C7012 Electric Slider LTS Robot Kit 27 9.95C7015 Mysterious Sound Kit 51 5.95C7019 Adj Flashing Bright Light LED Kit 37 4.25C7021 Brightest Landscape Light Kit 11 14.95C7021B Brightest Landscape Light (Pkg of 4) 11 49.95C7022 Solar Nite Screamer Kit 11 9.95C7023 Beta Gamma Geiger Counter Kit 8 129.00C7025 Sensitive 2Ch Color Organ 32 17.95C7026 Giant Geiger Counter Kit 8 149.00C7029 POV Kit 24 16.95C7030 Rotating POV Kit 24 22.95Column C TotalStock# Description Pg# Qty. CostColumn D TotalFax US: (480) 451Call Us: 1-800-227C7034 Large Glowing Light Panel Kit 36 10.95C7035 Giant Super Power Strobe Kit 47 29.95C7037 Kinetic Pirates Desk Sculpture Kit 52 9.95C7038 Kinetic Pirate Boat Sculpture Kit 52 8.95C7041 Solar House “Green Energy” Lab 13 49.95C7043 Chaney MCU Lab w/ Programmer 12 134.95C7045 Ultimate Learn to Solder Kit 4 4.95C7048 “Speedster 500” Robot Kit 4,60 13.95C7048ASB “Speedster 500” Robot Kit (ASB) 4,60 19.95C7055 0-12V 1Amp Regulated Power Supply 5 21.95C7056 SCI-TEC Rover Kit 5,60 34.95C7058 Guitar Practice Amp Kit with Case 5,60 19.95C7060 GM22 Geiger Counter Kit 4 79.95C7060ASB GM22 Geiger Counter Kit (ASB) 4 99.95C7061ASB World’s Smallest Geiger Counter 4 129.00C7062A Single Blinding White LED Driver 5 5.95C7062B Double Blinding White LED Driver 5 7.75C7062C Triple Blinding White LED Driver 5 9.00C7066 Super Solar Light Kit 5,10 11.95C7067 Large Area Solar Landscape Light Kit 5,11 15.95C7067B Lg Area Slr Lndscp Light Kit (4 Pk) 5,11 52.95C7069 GM12 Geiger Counter Kit 4 69.95C7800 The Atom PP Course 6 29.95C7801 Current, Voltage & Resistance PP 6 29.95C7802 Ohm’s Law PP Course 6 29.95C7803 Resistor Color Code PP Course 6 29.95C7804 Component ID and Schematics PP 6 29.95C7805 Learn to Solder PP Course 6 29.95C7806 All Six PP Training Courses 6 159.95C8043 Chaney MCU Lab (No Programmer) 12 99.95C8100 Blinder Kit Bulk Package of 25 53 85.00C8101 Phasor Kit Bulk Package of 25 53 145.00C8102 Chirper Kit Bilk Package of 25 53 99.00C8103 TOWS Kit Bulk Package of 25 53 95.00C8104 Jitterbug Kit Bulk Package of 25 53 119.00C8105 Expression Kit Bulk Pkg of 25 53 105.00C8106 Chaser Kit Bulk Package of 25 53 90.00C8600 Ultimate Geiger Counter w/o Tube 4 25.95C8600ASB Assem Ult Geiger Cntr w/o Tube 4 39.95C9001 Current, Voltage & Resistance CBT 6 34.95C9002 Ohm’s Law CBT 6 34.95C9003 Resistor Color Code CBT 6 34.95C9004 Component Identification CBT 6 34.95C9005 Learn to Solder CBT 6 34.95C9006 All 5 CBTs 6 164.95C18976 Glass Solar Powered Propeller Prj 11 6.00TO ORDER: 1-800-227-7312 • FAX: (480) 451-9495Chaney Electronics, Inc. • PO Box 4116 • Scottsdale, AZ 85261 • www.chaneyelectronics.com 57

School NameTeacher NameAddress24 Hour FAX Line1-480-451-9495Business Office1-480-451-9407CHANEY ELECTRONICSP.O. BOX 4116SCOTTSDALE, AZ 85261CALL TOLL FREE8:00 AM - 4:00 PM M-F(Arizona Time)1-800-227-7312City State ZIP PhonePurchase Order #:Check/Money OrderVISA/MastercardAMEXOpen Account(Schools Only)PO#_____________PLEASEINDICATEMETHOD OFPAYMENTCredit Card InformationCard Number:Exp Date:Card Holder Name (Please Print):Billing Address for Card:City: State: Zip:To facilitate the selection of our products, we have designed a QUICK CHECK ORDER FORM for you to use when placing an order.Each product that we sell is listed on the QUICK CHECK ORDER FORM located on pages 56 and 57. Since we have over 220kits and many more parts and supplies, we recommend using this form to keep track of what you want. Please see the orderinginstructions on the next page for additional ordering information. Please fill in the boxes below to complete your order.Take the Total from each Column on the QUICK CHECKORDER FORM on pages 56 and 57 and enter the amounts inthe appropriate boxes.Add the totals from each column box above to get the subtotalShipping Charge–Add $7.00 if the order amount is less than $100.For orders shipped to Alaska, Hawaii, Canada, Guam, andPuerto Rico add 10% of the merchandise totalFor special express service charges, see the center box on page 59.MINIMUM ORDER $25.00 + SHIPPINGTotal column atotal column bTotal column ctotal column dSUBTOTAL (minimum $25)Tax (AZ Schools only)Shipping chargesRush Charges1 day 2 dayGrand totalAdd total plus tax (if applicable) and shippingcharges to come up with the Grand Total.Please Remember:1. There is a minimum order of $25.00 (plus shipping if order is under $100).2. We ship most orders within 24 hours.3. Phone orders must be placed by the teacher, Purchasing Agent, or Administrative Personnel.4. To order by phone, use our Toll Free Number: 1-800-227-7312.5. For Technical, Billing, Shipping, or any other Questions, call (480) 451-9407.6. Any technical questions must be made by the Teacher. Please do not have students call.Chaney Electronics disclaims any implied warranties of merchantability and fitness, arising in connection with the sale of anyproduct described in this catalog. In no event shall Chaney Electronics, Inc. be liable for any claim for incidental or consequentialdamages arising out of or in conjunction thereof with the manufacture, sale, delivery or use of any product in this catalog.NOTE: Specifications, prices and availability of items are subject to change without notice.

How do you make the best quality and best value educational electronic project kitsavailable today even better?We’ll ship them to you for free!!! We will pay for your Standard Ground shipping just foryour participation in our volume discount program. Here’s how it works:FREE SHIPPINGSimply place an order of $100.00 or more and you pay nothing for shipping**Free shipping is Standard Ground only. Canada, Hawaii, Alaska, Puerto Rico and Guam orders not eligible for free shipping(Please include 10% of your order for shipping to these locations).HOW TO ORDERTo make ordering as easy as possible, please use the following suggestions:1. Use the CONTENTS on Page 6, and the QUICK CHECK ORDER FORM on pages 56 and 57. The Contents is categorizedalphabetically and gives the name, stock number and page location of each of our products.2. To keep your New Catalog intact, please make copies of the QUICK CHECK ORDER FORM and use them for your actualorder. The QUICK CHECK ORDER FORM is designed to facilitate the process of purchasing products from us. Use it to help youwhen completing a Purchase Order, or when placing your order with one of our Toll Free Telephone Operators. Of course, if youwish, you can fax or mail your order to us as well (see STEP 3).3. If placing an order by fax or mail, please fill out the information area on Page 58. Be sure to include your method of payment.4. For classroom ordering, circulate both the Catalog and the quICK CHECK ORDER FORM to the students. Have the studentsplace tic marks next to the items that they wish to order. Alternatively, you can have each student come to you and you can use theQUICK CHECK ORDER FORM to conveniently select the products that you wish to purchase. When the QUICK CHECK ORDERFORM has been marked with the “tic marks” or quantity for each item, you should multiply each kit or product price to come up witha line by line subtotal and then add these together to enter into the subtotal box on page 58. Make sure that you fill out page 58completely or that you issue us your standard school purchase order.If sending your order in remember to include both pages of the QUICK CHECK ORDER FORM.PAYMENT: We accept Open Account Purchase Orders from Schools that are in good standing with our Credit Department.All Purchase Orders must be authorized by the School District. Terms are NET 30. We also accept Mastercard, Visa, MoneyOrders, Personal or School Checks. Sorry, we do not accept International Personal Checks.Shipping Charges:If your order is under $100, there will be a $7.00 Shipping/Handling Fee for Standard Ground Shipping. Orders that qualify for freeshipping will be sent anywhere in the Continental US via Standard Ground service only. Express delivery is available to customers atthe calculated Express shipping rate. Please Note: Express shipping can be quite expensive so please call for pricing.The options listed below are for 3 lbs or less and are only minimum fees and will increase according to weight and distance.Express Shipping Options:2 DAY $28.00 Minimum Fee Delivery in 2 Business Days1 DAY $58.00 Minimum Fee Delivery in 1 Business DayALASKA, HAWAII, CANADA, GUAM, and PUERTO RICO Orders will be charged a shipping charge of 10% of the TotalProduct Price. All Orders must be paid in U.S. funds. Please call for express shipping options.RETURNS AND REPAIRS:1. Any returns or repairs must be authorized prior to shipping and made within 30 days of the original invoice date.2. Any returned kit must be unopened and unused. All returns are subject to a 15% Restocking Fee.3. Chaney Electronics will provide Repairs on our Kits up to 30 days from their original invoice date for schools/teachers only,providing that the kit has been assembled correctly on our circuit board per our instructions and have been completely checkedby the instructor. If there are assembly and/or soldering errors there will be a charge for the repair work. We cannot accept kitsthat have been soldered with Acid Core Solder. In addition, our repair policy does not apply to any SMD/Hybrid Kit that usesSMD components.4. If the student has made assembly errors you will be advised of the cost of repairs before any work is done.5. Include copy of Original Invoice.TO ORDER: 1-800-227-7312 • FAX: (480) 451-9495

CHANEY P.O. Box 4116ELECTRONICS, INC. Scottsdale, AZ 852611-800-227-7312 • Fax: (480) 451-9495CHANEY ELECTRONICS Call to Order Today! 1-800-227-7312 • Fax: (480) 451-9495www.chaneyelectronics.comSCI-TEC Rover Kit(No Soldering Necessary)This fun and educational SCI-TEC Rover comes with 10 activities/experiments. There is no soldering necessary for this excitingproject. Parts simply snap together and wires are twisted ontoconnectors. Features a powerful motor with gear to propel yourrover on almost any surface (including most carpets). Operateson 2 AA batteries (not included). Completed SCI-TEC Rover isabout 9.5” long x 5” wide x 5” high. Learn about lamps, motors,circuits, and different types of propulsion! Complete with all partsand detailed instruction booklet. Skill level 1.C7056 $34.95Guitar Practice Amp Kit with CaseThe Guitar Practice Amplifier Kit with Case is perfect for anyaspiring guitar musician! Operates on one 9V battery (notincluded) and delivers up to 1Watt of guitar music from a builtin 3-1/2” speaker, Features standard 1/4” female jack for guitarcord, volume control, tone control, on/off switch, “on” indicatorand compact case of 4.25” square x 2.25” high. Comes with allparts, PC board, case and knobs. Skill level 2.C7058 $19.95“Speedster 500” Robot KitThis quick and zippylittle robot zooms andturns along smooth hardsurfaces while flashingits colorful “headlights”.The “Speedster 500”robot operates from twotiny electronic brainsthat consist of flashingrainbow LEDs. Each timeone of the LEDs flash,it causes the robot toturn in a different direction. Operates from one 9V battery (notincluded). Size of board is 2.7” x 2”. Complete with all parts.Requires soldering. Skill Level 1. This robot is also availablefully assembled (9V battery not included).C7048 $13.95Also Available Fully AssembledC7048ASB $19.95 (No Soldering)