TORK MODEL W100 TORK® - Water Heater Timers Save Money

http://waterheatertimer.org/Tork-timers-and-manuals.html
SWITCH: SPST
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
120VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
TORK MODEL W100
SEVEN DAY CALENDAR DIAL TIME SWITCH
Disconnect power at main panel prior to installing or servicing this time switch or
the equipment connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C
(167 degrees F)
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON and OFF trippers close and
open all circuits simultaneously. Dial is graduated in one hour intervals.
There must be an ON and an OFF tripper for each day of the
week operations are desired. Place tripper on dial edge as shown in
diagram. Set point of each tripper at the desired operating time.
Hold tripper securely against dial and tighten knurled screw firmly
by hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes. DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close circuit.
Press down lever on left of nameplate to open it.
LI-598(A)
H
N
MOTOR
MOTEUR
TORK ®
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
▲
L 1 X 2
Typical connections for 120VAC
OFF
TRIPPER
ON
TRIPPER
MANUAL
OFF
LEVER
A M
WED
MIDNIGHT
S E T
TUE
NOON
P M A M
OFF
MIDNIGHT
ON
T I
M E
N
9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 11
10 8 6 4 2 12 10 8
➤
P M
LOAD
CHARGE
CARGA
ON
MIDNIGHT
A M
TIME
POINTER
P M
9 7 5 3 1 11 9 7 5
6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4
O
F
F
O
TORK N➤
TIME
MANUAL
ON
LEVER

SWITCH: SPDT
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
120VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
TORK MODEL W120
SEVEN DAY CALENDAR DIAL TIME SWITCH
Disconnect power at main panel prior to installing or servicing this time switch or
the equipment connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C
(167 degrees F)
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON trippers close circuit A. OFF
trippers close circuit B. Dial is graduated in one hour intervals.
There must be an ON and an OFF tripper for each day of the week
operations are desired. Place tripper on dial edge as shown in diagram.
Set point of each tripper at the desired operating time. Hold
tripper securely against dial and tighten knurled screw firmly by
hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
H
N
L 1 X 2
LOAD A
CHARGE A
CARGA A
MOTOR
MOTEUR
OFF
TRIPPER
ON
TRIPPER
TIME
POINTER
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes. DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close circuit.
Press down lever on left of nameplate to open it.
TORK ®
LI-602(A)
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
▲
▼
MANUAL
OFF
LEVER
A M
WED
MIDNIGHT
S E T
TUE
NOON
P M A M
OFF
MIDNIGHT
ON
T I
M E
N
9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 11
10 8 6 4 2 12 10 8
LOAD B
CHARGE B
CARGA B
➤
P M
ON
MIDNIGHT
A M
P M
9 7 5 3 1 11 9 7 5
6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4
O
F
F
H
N
TIME
O
N
TORK ➤
MANUAL
ON
LEVER

SWITCH: DPST
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
208-277VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
H
H
TORK MODEL W202
SEVEN DAY CALENDAR DIAL TIME SWITCH
L
MOTOR
MOTEUR
1 X 2
LOAD
CHARGE
CARGA
Disconnect power at main panel prior to installing or servicing this time switch or
the equipment connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C
(167 degrees F)
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON and OFF trippers close and
open all circuits simultaneously. Dial is graduated in one hour intervals.
There must be an ON and an OFF tripper for each day of the
week operations are desired. Place tripper on dial edge as shown in
diagram. Set point of each tripper at the desired operating time.
Hold tripper securely against dial and tighten knurled screw firmly
by hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
OFF
TRIPPER
ON
TRIPPER
TIME
POINTER
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes. DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close circuit.
Press down lever on left of nameplate to open it.
TORK ®
LI-599(A)
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
H
N
MOTOR
MOTEUR
L 1 X 2
MANUAL
OFF
LEVER
A M
WED
MIDNIGHT
S E T
TUE
NOON
P M A M
OFF
MIDNIGHT
ON
T I
M E
N
9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 11
10 8 6 4 2 12 10 8
➤
P M
ON
MIDNIGHT
A M
P M
9 7 5 3 1 11 9 7 5
6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4
O
F
F
CHARGE
CARGA
LOAD LOAD
Typical for 208-240VAC supply. Typical for 277VAC supply.
TIME
O
N
TORK ➤
CHARGE
CARGA
MANUAL
ON
LEVER

SWITCH: DPDT
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
120VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
TORK MODEL W220
SEVEN DAY CALENDAR DIAL TIME SWITCH
FRONT
FRENTE
ARRIÉRE
ESPLADA
FRONT
Disconnect power at main panel prior to installing or servicing this time switch or
the equipment connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C
(167 degrees F)
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON trippers close circuits 1 and 3.
OFF trippers close circuits X and 5. Dial is graduated in one hour
intervals. There must be an ON and an OFF tripper for each day of
the week operations are desired. Place tripper on dial edge as
shown in diagram. Set point of each tripper at the desired operating
time. Hold tripper securely against dial and tighten knurled screw
firmly by hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
OFF
TRIPPER
ON
TRIPPER
TIME
POINTER
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes. DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close circuit.
Press down lever on left of nameplate to open it.
TORK ®
LI-603(A)
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
H
REAR
N
L
MOTOR
MOTEUR
1 X 2
L 3 5 4
MANUAL
OFF
LEVER
A M
WED
MIDNIGHT
S E T
TUE
NOON
P M A M
OFF
MIDNIGHT
ON
T I
M E
N
9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 11
10 8 6 4 2 12 10 8
➤
LOADS
CHARGE
CARGA
LOADS
CHARGE
CARGA
Typical connections for 120VAC.
P M
ON
MIDNIGHT
A M
P M
9 7 5 3 1 11 9 7 5
6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4
O
F
F
H
N
H
N
TIME
O
N
TORK ➤
MANUAL
ON
LEVER

SWITCH: DPDT
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
120VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
SYNCHRONOUS POWER WITH RESERVE:
Should your power supply be interrupted, this switch
will continue to operate on time for several hours.
TORK MODEL W220L
SEVEN DAY CALENDAR DIAL TIME SWITCH
FRONT
FRENTE
ARRIÉRE
ESPLADA
FRONT
Disconnect power at main panel prior to installing or servicing this time switch or the equipment
connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C (167 degrees F)
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON trippers close circuits 1 and 3.
OFF trippers close circuits X and 5. Dial is graduated in one hour
intervals. There must be an ON and an OFF tripper for each day of
the week operations are desired. Place tripper on dial edge as
shown in diagram. Set point of each tripper at the desired operating
time. Hold tripper securely against dial and tighten knurled screw
firmly by hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
OFF
TRIPPER
ON
TRIPPER
TIME
POINTER
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes. DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close circuit.
Press down lever on left of nameplate to open it.
TORK ®
LI-604(A)
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
H
REAR
N
L
MOTOR
MOTEUR
1 X 2
L 3 5 4
LOADS
CHARGE
CARGA
Typical connections for 120VAC.
MANUAL
OFF
LEVER
A M
WED
MIDNIGHT
S E T
TUE
NOON
P M A M
OFF
MIDNIGHT
ON
T I
M E
N
9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 11
10 8 6 4 2 12 10 8
➤
LOADS
CHARGE
CARGA
P M
ON
MIDNIGHT
A M
P M
9 7 5 3 1 11 9 7 5
6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4
O
F
F
H
N
H
N
TIME
O
N
TORK ➤
MANUAL
ON
LEVER

SWITCH: DPDT
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
208-277VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
TORK MODEL W222
SEVEN DAY CALENDAR DIAL TIME SWITCH
FRONT
FRENTE
Timing
motor
supply
TIMING MOTOR SUPPLY CAN BE TAKEN BY JUMPER
WIRE FROM TERM. L TO 2 (FRONT TERM.) & L TO 4
FROM BACK IF VOLTAGE IS THE SAME.
ARRIÉRE
ESPLADA
FRONT
Disconnect power at main panel prior to installing or servicing this time switch or
the equipment connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C
(167 degrees F)
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON trippers close circuits 1 and 3.
OFF trippers close circuits X and 5. Dial is graduated in one hour
intervals. There must be an ON and an OFF tripper for each day of
the week operations are desired. Place tripper on dial edge as
shown in diagram. Set point of each tripper at the desired operating
time. Hold tripper securely against dial and tighten knurled screw
firmly by hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
L
L
REAR
MOTOR
M
MOTEUR
L
WATER
HEATER
1 X 2
L 3 5 4
OFF
TRIPPER
ON
TRIPPER
TIME
POINTER
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes. DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close circuit.
Press down lever on left of nameplate to open it.
TORK ®
LI-605(A)
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
L
SERVICE PANEL
L L
FRONT
FRENTE
ARRIÉRE
ESPLADA
MANUAL
OFF
LEVER
FRONT
A M
H
REAR
N
WED
MIDNIGHT
S E T
TUE
NOON
P M A M
OFF
MIDNIGHT
ON
T I
M E
N
9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 11
10 8 6 4 2 12 10 8
➤
P M
ON
MIDNIGHT
A M
P M
9 7 5 3 1 11 9 7 5
6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4
O
F
F
L
L 3
MOTOR
MOTEUR
1 X 2
3
5
4
LOADS
CHARGE
CARGA
Typical for 207/240VAC supply. Typical for 277VAC supply.
TIME
O
N
TORK ➤
4
2
LOADS
CHARGE
CARGA
1
MANUAL
ON
LEVER

SWITCH: 3PST
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
120VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
TORK MODEL W300
SEVEN DAY CALENDAR DIAL TIME SWITCH
Disconnect power at main panel prior to installing or servicing this time switch or
the equipment connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C
(167 degrees F)
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON and OFF trippers close and
open all circuits simultaneously. Dial is graduated in one hour intervals.
There must be an ON and an OFF tripper for each day of the
week operations are desired. Place tripper on dial edge as shown in
diagram. Set point of each tripper at the desired operating time.
Hold tripper securely against dial and tighten knurled screw firmly
by hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes. DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close circuit.
Press down lever on left of nameplate to open it.
LI-600(A)
FRONT
FRENTE
MILIEU
MEDIO
ARRIÉRE
ESPLADA
FRONT
L
L
L
N
L
MIDDLE
REAR
MOTOR
MOTEUR
▲
1 X
▲
3
▲
5
LOADS
CHARGE
CARGA
For use with 3 phase 4-wire 120/208VAC systems.
OFF
TRIPPER
ON
TRIPPER
TIME
POINTER
TORK ®
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
2
4
6
MANUAL
OFF
LEVER
A M
WED
MIDNIGHT
S E T
TUE
NOON
P M A M
OFF
MIDNIGHT
ON
T I
M E
N
9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 11
10 8 6 4 2 12 10 8
➤
P M
ON
MIDNIGHT
A M
P M
9 7 5 3 1 11 9 7 5
6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4
O
F
F
TIME
O
N
TORK ➤
MANUAL
ON
LEVER

SWITCH: 3PST
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
208-277VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
TORK MODEL W302
SEVEN DAY CALENDAR DIAL TIME SWITCH
Disconnect power at main panel prior to installing or servicing this time switch or
the equipment connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C
(167 degrees F)
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON and OFF trippers close and
open all circuits simultaneously. Dial is graduated in one hour intervals.
There must be an ON and an OFF tripper for each day of the
week operations are desired. Place tripper on dial edge as shown in
diagram. Set point of each tripper at the desired operating time.
Hold tripper securely against dial and tighten knurled screw firmly
by hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes. DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close circuit.
Press down lever on left of nameplate to open it.
LI-601(A)
FRONT
FRENTE
FRONT L 1 X
MILIEU
MEDIO
ARRIÉRE
ESPLADA
L
M
▲
▲
MIDDLE 3
L
L
N
MOTOR
MOTEUR
▲
REAR 5
2
4
6
LOADS
CHARGE
CARGA
For use with 3 phase 4-wire 120/208V systems.
FRONT
FRENTE
OFF
TRIPPER
ON
TRIPPER
MANUAL
OFF
LEVER
TIME
POINTER
TORK ®
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
MILIEU
MEDIO
FRONT L 1 X
H
N
A M
WED
MIDNIGHT
S E T
TUE
NOON
P M A M
OFF
MIDNIGHT
ON
T I
M E
N
9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 1 11 9 7 5 3 11
10 8 6 4 2 12 10 8
➤
M
▲
▲
MIDDLE 3
▲
REAR 5
ARRIÉRE
ESPLADA
MOTOR
MOTEUR
P M
ON
MIDNIGHT
A M
P M
9 7 5 3 1 11 9 7 5
6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4 2 12 10 8 6 4
O
F
F
2
4
6
LOADS
CHARGE
CARGA
Typical connections for 277VAC supply.
TIME
O
N
TORK ➤
MANUAL
ON
LEVER