Owner’s Manual

More documents

Recommendations

Info

TEMP ▲ button Increases the temperature SET button Used to initiate advanced panel features. OPERATING INSTRUCTIONS CONTROL PANELS Cantabria Main Control Panel LIGHT button Activates the interior and exterior lighting JETS 1 button Activates jet pump 1 and waterfall JETS 2 button Activates jet pump 2 and waterfall TEMP ▼ button Decreases the temperature JETS 1 button Activates jet pump 1 and waterfall AIR button Activates the air jets LIGHT button Activates the interior and exterior lighting JETS 2 & 3 button Activates jet pumps 2 and 3 and waterfall Auxiliary Panel TEMP ▲ button Increases the temperature SET button Used to initiate advanced panel features. TEMP ▼ button Decreases the temperature 2 & 3 Geneva • Tahitian ® • Niagara ® Main Control Panel 3 Speed button Determines the amount of time between steps in a jet sequence Pause button Interrupts sequence and prolongs jets JETS 3 button Activates jet pump 3 AIR & CLEAN button Activates air jets and the ten-minute clean-up cycle UltraMasseuse Control Panel Massage Sequence Indicator Lights Sequences button Selects preprogrammed jet sequence JETS 1 button Activates jet pump 1 AIR button Activates the air jets CLEAN button Activates a ten-minute clean-up cycle LIGHT button Activates the interior and exterior lighting JETS 1 button Activates jet pump 1 AIR button Activates the air jets LIGHT button Activates the interior & exterior lighting JETS 2 button Activates jet pump 2 & Waterfall Auxiliary Panel 24 JETS 2 button Activates jet pump 2 and waterfall
OPERATING INSTRUCTIONS TEMP ▲ button Increases the temperature CONTROL PANELS Elation ® Main Control Panel JETS 1 button Activates jet pump 1 SET button Used to initiate advanced panel features. TEMP ▼ button Decreases the temperature JETS 1 button Activates jet pump 1 MODE button Switches between spa mode and stereo mode L/T/S button Activates lighting, CD track and radio scan JETS 2 button Activates jet pump 2 & Waterfall Auxiliary Panel CLEAN button Activates a ten-minute clean-up cycle LIGHT button Activates the interior & exterior lighting JETS 2 button Activates jet pump 2 and waterfall MAIN CONTROL PANEL BUTTONS AND DISPLAY Your spa control system consists of an illuminated Light Emitting Diode (LED) and convenient push buttons that allow you to set the water temperature, as well as the hydrotherapy jets, mood lighting, and optional jets from the spa control panel. DISPLAY INVERSION You may invert the main, four-digit display for easier viewing from inside the spa. Press and hold the “SET” button for three seconds until the display is inverted. Press and hold the “SET” button for three seconds a second time to invert the four-digit display back to its original position. TEMPERATURE Control The set temperature range is from 80°F (27°C ) to 104°F (40°C). The set temperature of the spa water will automatically be 100°F (38°C) the first time power is applied. This is the setting programmed at the factory. After the spa has been set up and used, the last temperature value set by the user will be stored in memory. If power is disconnected from the spa, it will automatically revert to the last set temperature when power is reapplied. (Temperatures of any setting may rise slightly depending on the current use and condition of your spa and on outside temperature.) To display the set temperature of the spa, press the “TEMP ▲ “ or “TEMP ▼ “ button. The set temperature will be displayed, unless the spa is locked (in which case the word SPA is displayed with the lock symbol). The set temperature display will automatically return to actual temperature after five seconds. To increase the set temperature of the spa water, press the “TEMP ▲ “ button. Each time the button is pressed, the set temperature display will increment by one degree. If the button is held down, the set temperature display will increase by one degree every half-second. To decrease the set temperature of the spa water, press the “TEMP ▼ “ Each time the button is pressed, the set temperature display will decrement by one degree. If the button is held down, the set temperature display will decrease by one degree every half-second. If the set temperature value will not change, check the TEMP LOCK and SPA LOCK features. When either of these features is applied, the temperature control is disabled. 25
Page 2 and 3: WELCOME Watkins Manufacturing Corpo
Page 4 and 5: IMPORTANT SAFETY INSTRUCTIONS Read
Page 6 and 7: SAFETY INSTRUCTIONS To reduce the r
Page 8 and 9: Controls and Equipment UTOPIA Canta
Page 10 and 11: Controls and Equipment Utopia niaga
Page 12 and 13: Controls and Equipment 1 20 14 23 2
Page 14 and 15: ELECTRICAL INSTALLATION CANTABRIA
Page 16 and 17: ELECTRICAL REQUIREMENTS AND PRECAUT
Page 18 and 19: START-UP AND REFILL PROCEDURES Your
Page 20 and 21: CUSTOMIZING YOUR MASSAGE Euro Direc
Page 22 and 23: JET MENU UTOPIA GENEVA Jet Pump 1
Page 24 and 25: JET MENU Utopia Tahitian ® Jet Pum
Page 28 and 29: OPERATING INSTRUCTIONS JETS button
Page 30 and 31: OPERATING INSTRUCTIONS If the exter
Page 32 and 33: EQUIPMENT COMPARTMENT CONTROLS SIDE
Page 34 and 35: EQUIPMENT COMPARTMENT CONTROLS SIDE
Page 36 and 37: MAINTENANCE FILTER MAINTENANCE At l
Page 38 and 39: MAINTENANCE 1. 2. 3. 4. 5. 6. 7. 8.
Page 40 and 41: WATER QUALITY AND MAINTENANCE It’
Page 42 and 43: WATER QUALITY AND MAINTENANCE If th
Page 44 and 45: WATER QUALITY AND MAINTENANCE warni
Page 46 and 47: WATER QUALITY AND MAINTENANCE monar
Page 48 and 49: SERVICE MISCELLANEOUS SERVICE INFOR
Page 50 and 51: COMFORTGUARD ® Watkins Manufacturi
Page 52: Utopia Series specifications This m

Owner’s Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?